Ìtọ́sọ́nà Ìtọ́sọ́nà NICREW ClassicLED Plus LED Aquarium Light (15W, 18-24 Inch)

1. Ifihan

The NICREW ClassicLED Plus LED Aquarium Light is designed to provide optimal lighting for freshwater or saltwater fish and low-to-medium light level aquatic plants. This full-spectrum light combines 6500K white, 450nm blue, TRUE 660nm deep red, and green LEDs to produce a fine-tuned color spectrum. It features a programmable timer with adjustable auto On/Off times, brightness, and ramp-up/dim-down periods to simulate natural sunrise and sunset cycles.

2. Awọn ilana aabo

• Always unplug the fixture from the power outlet before performing any maintenance or cleaning.
• This product is designed for indoor use only. Do not immerse the light fixture in water.
• Ensure the power cord is not damaged. If damaged, do not operate the fixture.
• Jeki kuro ni arọwọto awọn ọmọde.
• Do not operate if any part of the fixture is wet. Dry thoroughly before plugging in.
• Ensure the light is securely mounted on the aquarium to prevent accidental falls into the water.

3. Package Awọn akoonu

Jẹrisi pe gbogbo awọn nkan wa ati ni ipo to dara:

• NICREW ClassicLED Plus LED Aquarium Light Fixture
• Wired Controller with Timer
• Àwọn Báàkẹ́ẹ̀tì Ìfìsọpọ̀ Tí A Lè Ṣètò (2x)
• Adapter agbara

4. Eto ati fifi sori

1. Yọ Imọlẹ naa kuro: Carefully remove the light fixture and all components from the packaging.

   

   This image shows the main light fixture with its array of white, blue, red, and green LEDs, and the extendable mounting brackets attached.

2. So Awọn Biraketi Iṣagbesori: Slide the adjustable docking mounts onto both ends of the light fixture. These brackets allow for easy adaptation to fit most rimless and framed aquariums.

   

   The image highlights the extendable mounting bracket for flexible installation and the enhanced heat sink design for better heat dissipation.
3. Gbe Imọlẹ naa si: Place the light fixture securely on top of your aquarium. Adjust the extendable brackets to ensure a stable fit across the tank's width.

   

   This diagram illustrates the various sizes available for the ClassicLED Plus and their corresponding dimensions, ensuring proper fitment for tanks ranging from 12 to 54 inches.

4. So agbara: Plug the wired controller into the light fixture, then connect the power adapter to the controller and finally to a power outlet.

5. Awọn ilana Iṣiṣẹ

The NICREW ClassicLED Plus features a wired controller for programming the light cycle and adjusting settings. The light offers two independent channels: Channel 1 (CH1) for White, Red, and Green LEDs, and Channel 2 (CH2) for Blue LEDs.

5.1. Adarí Loriview

This image demonstrates the independent control of Channel 1 (White, Red, Green LEDs) and Channel 2 (Blue LEDs), with brightness adjustable from 0% to 100%. Note that manual mode brightness is fixed at 100%.

5.2. Ṣiṣeto Aago

The controller allows you to set a 24-hour light cycle with customizable on/off times, brightness levels, and ramp-up/dim-down periods for both channels. If you are changing pre-programmed settings, ensure the fixture is not left idle too long, or you may need to restart the process.

1. Tẹ awọn SET button to enter programming mode. The display will show "00:00" and flash.
2. Lo awọn WAKATI ati ISEJU awọn bọtini lati ṣeto awọn ti isiyi akoko.
3. Tẹ SET again. The display will show "ON" briefly, then flash the current time. Use WAKATI ati ISEJU to set the desired ON time for Channel 1 (White, Red, Green LEDs).
4. Tẹ SET. The display will show "OFF" briefly, then flash the current time. Use WAKATI ati ISEJU to set the desired OFF time for Channel 1.
5. Tẹ SET. The display will show "100" briefly. Use WAKATI (+) ati ISEJU (-) to set the brightness percentage (0-100%) for Channel 1.
6. Repeat steps c-e for Channel 2 (Blue LEDs).
7. Tẹ SET. The display will flash the current ramp time mode (00, 15, or 30). Use WAKATI (+) tabi ISEJU (-) to choose between 00 (straight on/off), 15 (15-minute ramp-up/dim-down), or 30 (30-minute ramp-up/dim-down).
8. Tẹ SET to save and exit the settings.

This graph visually represents a typical 24-hour light cycle, showing how Channel 1 (White, Red, Green LEDs) and Channel 2 (Blue LEDs) can be programmed with different on/off times, brightness levels, and ramp-up/dim-down periods to simulate natural lighting conditions.

5.3. Isẹ Afowoyi

To manually turn the light on or off, or switch between modes without using the timer, press the power button on the controller. In manual mode, the brightness is fixed at 100%.

5.4. Video Tutorial: Programming the Timer

This video provides a step-by-step guide on how to program the integrated timer on your NICREW ClassicLED Plus light, including setting the current time, on/off times for each channel, brightness, and ramp-awọn akoko soke/din-down.

6. Itọju

• Ninu: Regularly wipe the light fixture with a soft, dry cloth to remove dust and water spots. Ensure the light is unplugged before cleaning. Do not use abrasive cleaners or solvents.
• LED Surface: Gently clean the LED surface with a damp cloth if necessary. Avoid scratching the surface.
• Power Cord and Connections: Periodically inspect the power cord and all connections for any signs of damage or wear. Replace if necessary.

7. Laasigbotitusita

8. Awọn pato

• Awoṣe: N10372
• Wattage: 15 Wattis
• Imọlẹ: 850 Lumens
• Dimensions (Light Fixture): 17.52"L x 4.57"W x 2.52"H (for 18-24 inch tank)
• Ohun elo: Acrylic, Aluminum, Glass
• Orisun Imọlẹ Imọlẹ: LED (funfun 6500K, buluu 450nm, pupa jinlẹ TRUE 660nm, alawọ ewe)
• Ọna Iṣakoso: Wired Controller with Timer
• Orisun Agbara: Okun Itanna (20V DC)
• Ipele Resistance Omi: Not Water Resistant (Do not immerse)

9. Atilẹyin ọja ati Support

NICREW products are designed for ease of use and enjoyment. This product comes with a hassle-free 12-month warranty. For any questions, concerns, or technical support, please contact NICREW customer service. We are dedicated to providing quality products and support to ensure a better fish keeping experience.

For further assistance, please visit the official NICREW Store: NICREW Store on Amazon