1. Introduction and Compatibility
This manual provides detailed instructions for the installation, operation, and maintenance of the wellye RX23 12V Bluetooth Remote Control and Receiver Kit, designed for children's electric ride-on cars. Please read this manual thoroughly before use to ensure proper functionality and safety.
1.1 Ayẹwo ibamu
To ensure this control box fits your specific ride-on car, open the existing control box in your electric ride-on car and compare its appearance and model number. This kit is compatible if the appearance and the model number (RX23 12V) match your original unit.
Aworan 1.1: Pariview of the wellye RX23 12V Bluetooth Remote Control and Receiver Kit, showing both the remote control and the receiver unit.
Aworan 1.2: Isunmọ view of the wellye RX23 12V receiver unit, highlighting its connectors and casing.
Image 1.3: The wellye RX23 12V receiver unit, showing the "RX23 12V" label on its side, crucial for compatibility verification.
2. Alaye Aabo
For external use only. Keep away from naked flame or direct heat sources. This product is intended for use with children's ride-on toys. Adult supervision is recommended during installation and operation.
3. Eto ati fifi sori
3.1 Latọna jijin Iṣakoso batiri sori
The remote control requires two AAA 1.5V batteries. Use a Phillips screwdriver to unscrew the screw on the back of the remote control. Open the battery cover, install the batteries, ensuring correct positive (+) and negative (-) polarity, then close the battery cover and secure the screw.
- Maṣe dapọ atijọ ati awọn batiri titun.
- Maṣe dapọ awọn oriṣi awọn batiri.
- Remove exhausted batteries from the remote control promptly.
Aworan 3.1: Ẹyin view of the remote control, showing the battery compartment and basic operation instructions.
3.2 Frequency Matching (Pairing)
Frequency matching is required for the first use or after replacing the remote control batteries. If the matching is unsuccessful, turn off the car's power and repeat steps 2 and 3.
- Install two AAA 1.5V batteries into the remote control, observing correct polarity. The indicator light will flash three times, confirming correct battery installation.
- Press and hold the frequency key (often labeled "car select" or "S") on the remote control for approximately 2 seconds. The indicator light on the remote will begin to flash.
- Turn on the power supply of the ride-on car. The indicator light on the remote control will turn off, indicating successful frequency matching.
- If the indicator light does not turn off, the matching was unsuccessful. Turn off the car's power and repeat steps 2 and 3.
4. Awọn ilana Iṣiṣẹ
Once the remote control and receiver are successfully paired, you can operate the ride-on car using the remote control. The remote control will enter power-saving mode if not operated for 10 seconds, and the indicator light will turn off.
4.1 Isakoṣo latọna jijin Apejuwe
Aworan 4.1: Isunmọ view of the wellye remote control, showing the various control buttons.
- ▲ (Ofa ti oke): Moves the car forward.
- ▼ (Ọfà isalẹ): Moves the car backward.
- ◀ (Left Arrow): Turns the car left.
- ▶ (Right Arrow): Turns the car right.
- S (Speed/Select): Controls speed settings or acts as the frequency matching button.
- P (Emergency Brake): Press this button to engage the emergency brake. The car's running function will stop. Press again to release.
5. Itọju
Regular maintenance ensures the longevity and proper functioning of your remote control and receiver kit.
- Itọju Batiri: Always use fresh batteries of the same type. Remove batteries if the remote control will not be used for an extended period to prevent leakage.
- Ninu: Fi aṣọ gbígbẹ àti aṣọ rírọ̀ nu iṣakoso latọna jijin ati olugba naa. Maṣe lo awọn kemikali lile tabi awọn afọmọ fifọ.
- Ibi ipamọ: Tọju ohun elo naa ni itura, aye gbigbẹ kuro lati orun taara ati awọn iwọn otutu to gaju.
6. Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Remote control not responding / Car not moving |
|
|
| Remote control indicator light flashes continuously after battery installation | Frequency matching is required. | Perform frequency matching (refer to Section 3.2). |
| Remote control indicator light does not turn off after attempting frequency matching | Frequency matching failed. | Turn off the car's power, then repeat steps 2 and 3 of the frequency matching process (Section 3.2). |
| Car moves erratically or in wrong direction | Wiring issue or faulty receiver. | Verify all wiring connections to the receiver are secure and correctly installed. If issues persist, the receiver may be faulty and require replacement. |
7. Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Nọmba awoṣe | WEELYE RX23 12V 7-pin single-side |
| Voltage | 12V |
| Asopọmọra | 2.4G Bluetooth |
| Awọn batiri Iṣakoso latọna jijin | 2 x AAA 1.5V (ko si) |
| Ọja Mefa | 3.5 x 3.5 x 2 inches (Receiver) |
| Iwọn Nkan | 4.7 iwon |
| Olupese | daradara |
8. Atilẹyin ọja ati Support
For technical support or inquiries regarding this product, please contact wellye customer service. Refer to your purchase documentation for specific warranty details, as warranty terms may vary by retailer and region.
For more information about wellye products, visit the wellye brand store on Amazon.
