Ọrọ Iṣaaju
This manual provides detailed instructions for the installation, operation, and maintenance of the DIGITEN DFC15 Water Flow Control System. This system is designed for precise measurement and control of water flow, suitable for various applications requiring quantitative liquid dispensing.
Package Awọn akoonu
The DIGITEN DFC15 Water Flow Control System package includes the following components:
- 1 x DFC15 Controller
- 1 x G3/4" Flow Sensor
- 1 x G3/4" Electric Solenoid Valve (Normally Closed)
- 1 x DC 12V Power Adapter
- 1 x Sensọ iwọn otutu
- 1 x Itọsọna olumulo
Ipariview of all components included in the DIGITEN Water Flow Control System kit, featuring the DFC15 controller, G3/4" flow sensor, G3/4" solenoid valve, power adapter, and temperature sensor.
Imọ ni pato
DFC15 Controller
- Ibeere agbara: 12VDC
- Adapter agbara: Input: 100-240VAC; Output: 12VDC, max 2A
- Adapter Lead Length: 1m
- Wiwọn Yiye: ± 1%
- Output for Solenoid Valve: 12VDC, o pọju 5A
- Sensọ iwọn otutu: 0-125℃/32-257℉, NTC3950, Accuracy: ±1℃/±1℉, Thread: M8
- Max Total Volume: 999999 G/L
- Quantitative Range: 0-9999.99 G/L
- Ibiti Oṣuwọn Sisan: 0-9999.99 LPM (GPM)
- Gigun USB: 1m
- Awọn iwọn: 88mm x 126mm x 30mm
- Ìwúwo: 200g
- Ayika Isẹ: Temperature: 0-50℃/32-122℉; Relative Humidity: <85%
G3/4" Flow Sensor
- Igbohunsafẹfẹ: F=5.5 * Q (L / Min)
- Range sisan 1-60L / iseju
- Allowable Compression: Water pressure 1.75 Mpa below
- Orisi sensọ: Hall ipa
- Gigun USB: 15cm
- Asise: ± 2%
G3/4" Solenoid Valve
- Ipa Ṣiṣẹ: 0.02-0.8Mpa
Eto ati fifi sori
Proper installation is crucial for accurate operation. Follow these steps:
- Ifisilẹ Awọn Apakan: Properly install the flow sensor and solenoid valve in the water line. Ensure the flow sensor and solenoid valve direction aligns with the water flow direction. An arrow on the flow sensor indicates the correct flow path.
- Asopọmọra: Connect the flow sensor, solenoid valve, and temperature sensor to the DFC15 controller according to the wiring diagram. Connect the 12VDC power adapter to the controller.
- Awọn Eto Ibẹrẹ: Before operation, set the K value, quantitative value, and maximum alarm value on the DFC15 controller. Refer to the operating instructions for details on setting these parameters.
- Awọn ero Ayika: Avoid exposing the controller to water or excessive humidity to prevent damage.
A schematic diagram illustrating the wiring connections for the DIGITEN DFC15 controller, power adapter, solenoid valve, temperature sensor, and flow sensor, along with their placement in the water line.
An illustrative diagram showing a typical installation of the DIGITEN water flow control system, with the controller, solenoid valve, and flow sensor integrated into a water pipe.
The G3/4 inch water flow sensor, highlighting the arrow indicating the correct direction of water flow for proper installation.
Awọn ilana Iṣiṣẹ
Once the system is installed and initial settings are configured, follow these steps for operation:
- Bẹrẹ Iṣiṣẹ: Tẹ awọn RUN / Duro button to initiate the control process. The controller will begin displaying the current flow volume, current flow rate, and the faucet animation will start.
- Quantitative Control: The controller will automatically turn off the solenoid valve when the total flow reaches the pre-set quantitative value. At this point, the total value display will stop, the faucet animation will cease, and the flow rate will return to zero.
- Repeat Operation: To repeat the same job, press the RUN / Duro bọtini lẹẹkansi.
The DIGITEN DFC15 LCD display controller, illustrating its dimensions and button layout for operation.
Itoju
To ensure the longevity and proper functioning of your DIGITEN DFC15 Water Flow Control System, observe the following maintenance guidelines:
- Protect the Controller: Always avoid direct contact of the controller with water or other liquids. Ensure it is installed in a dry environment.
- Ayẹwo igbagbogbo: Periodically check all connections for tightness and signs of wear.
- Ninu: Clean the exterior of the controller with a soft, dry cloth. Do not use abrasive cleaners or solvents.
Laasigbotitusita
If you encounter issues with your DIGITEN DFC15 Water Flow Control System, consider the following:
- Solenoid Valve Not Actuating: If you are using a solenoid valve that requires more than 2A, ensure you are using a suitable power adapter capable of supplying up to 5A. The included power adapter is rated for a maximum of 2A.
- Inaccurate Flow Readings: Verify that the flow sensor is installed correctly with the water flow direction matching the arrow on the sensor. Check for any blockages in the flow path.
- Adarí Ko Ṣiṣẹ Tan-an: Ensure the 12VDC power adapter is securely connected to both the controller and a functional power outlet.
Atilẹyin ọja
The DIGITEN DFC15 Water Flow Control System comes with a 12-osu atilẹyin ọja lati ọjọ rira, ibora awọn abawọn iṣelọpọ. Jọwọ ṣe idaduro ẹri rira rẹ fun awọn iṣeduro atilẹyin ọja.
Atilẹyin
For further assistance, technical support, or warranty inquiries regarding your DIGITEN DFC15 Water Flow Control System, please contact DIGITEN customer service through their official channels.
