Ọrọ Iṣaaju
Thank you for choosing the Wellis Easy-Lifter Thermal Cover Lifter. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new cover lifter. Please read this manual thoroughly before installation and keep it for future reference.
Alaye Aabo
Always follow basic safety precautions when installing and operating the cover lifter to reduce the risk of injury or damage.
- Rii daju pe gbogbo awọn paati ti wa ni ṣinṣin ni aabo ṣaaju lilo.
- Do not allow children to operate the cover lifter unsupervised.
- Verify the hot tub cover is properly seated on the lifter arms before moving.
- Do not attempt to lift covers heavier than the recommended weight capacity.
- Use caution to avoid pinching hazards during operation.
Eto ati fifi sori
The Wellis Easy-Lifter is designed for quick installation and easy operation. It is suitable for almost any hot tub size due to its adjustable design.
Awọn akoonu idii:
- 1 x Wellis Easy-Lifter Thermal Cover Lifter (main assembly)
- Mounting hardware (screws, caps)
- Ilana itọnisọna (iwe yii)
Note: Hot tub and hot tub cover are not included.
Awọn igbesẹ fifi sori ẹrọ:
- Yọ awọn ohun elo kuro: Farabalẹ̀ yọ gbogbo àwọn ẹ̀yà ara kúrò nínú àpótí náà kí o sì ṣàyẹ̀wò rẹ̀ pẹ̀lú àkójọ àwọn ohun tí ó wà nínú àpótí náà.
- Ipo: Determine the optimal mounting location on your hot tub. The lifter is adjustable to fit hot tubs with lengths from 1750mm to 2350mm and widths from 1900mm to 2500mm. Ensure sufficient clearance behind the hot tub for the cover to rest when open.
- Gbigbe awọn Biraketi:
Attach the main mounting brackets to the side of your hot tub. Use the provided screws. It is recommended to pre-drill pilot holes to prevent cracking the hot tub skirting. A cardboard template can be useful for accurate drilling.
Image: Close-up of the Wellis Easy-Lifter's black mounting bracket securely attached to the wooden-look side panel of a hot tub. The bracket features a pivot point for the lifter arm.
- Assemble Lifter Arms: Connect the aluminum tubing sections to form the lifter arms. Ensure all connections are secure. The aluminum tubing is black powder-coated for durability.
- Attach Lifter Arms to Brackets: Secure the assembled lifter arms to the mounted brackets using the designated pins or bolts. Ensure free movement of the arms.
- Awọn atunṣe ipari: Adjust the length and width of the lifter arms to perfectly accommodate your hot tub cover. The lifter is designed to be ergonomically comfortable for use.
Awọn ilana Iṣiṣẹ
The Wellis Easy-Lifter allows for easy, single-person removal of your hot tub cover.
- Fold the Cover: Fold your hot tub cover in half, ensuring the fold is centered on the hot tub.
- Position the Lifter: Ensure the lifter arms are in their closed position, ready to receive the folded cover.
- Slide Cover onto Lifter: Carefully slide the folded hot tub cover onto the lifter arms. Ensure it is balanced and fully supported.
- Ṣii Ideri naa: Grasp the handle or a sturdy part of the lifter and gently push downwards and backwards. The lifter mechanism will pivot, allowing the cover to smoothly slide off the hot tub and rest in an upright, stored position behind the hot tub.
- Pa Ideri naa: To close, gently pull the lifter arms forward. The cover will pivot back over the hot tub. Carefully slide the cover back into its closed position.
Image: A hot tub with a black thermal cover being lifted by the Wellis Easy-Lifter. The cover is folded in half and supported by the lifter arms, resting vertically behind the hot tub.
Tip: When opening, lift from the center of the cover to prevent twisting of the frame, especially with heavier covers.
Itoju
Regular maintenance will ensure the longevity and smooth operation of your Wellis Easy-Lifter.
- Ninu: Pa fireemu aluminiomu ati awọn paati ṣiṣu kuro pẹlu ipolowoamp cloth periodically to remove dirt and debris. Avoid abrasive cleaners.
- Lubrication: Apply a silicone-based lubricant to the pivot points and moving parts annually or as needed to ensure smooth operation.
- Ṣiṣayẹwo ohun elo: Periodically inspect all screws and bolts to ensure they are tight. Re-tighten if necessary.
- Ayẹwo ibajẹ: Check for any signs of wear, corrosion, or damage to the frame or mounting brackets. Replace damaged parts immediately.
Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Lifter is stiff or difficult to move. | Lack of lubrication; dirt/debris in pivot points. | Clean pivot points and apply silicone lubricant. |
| Cover does not sit evenly on lifter. | Cover not centered; lifter arms not adjusted correctly. | Ensure cover is folded and centered. Check and adjust lifter arm length/width. |
| Screws or mounting hardware are loose. | Vibration or normal use over time. | Tun-mu gbogbo iṣagbesori skru. |
| Screw caps do not hold. | Screws sinking into plastic; manufacturing tolerance. | This is a known minor issue. Consider using a small amount of adhesive or painting the screw heads if desired. |
Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Orukọ awoṣe | Easy-Lifter |
| Brand | Wellis |
| Ohun elo | Aluminum (black powder-coated) |
| Iwọn Ọja | 5.8 kg (isunmọ.) |
| Ipad to ṣatunṣe | 1750mm - 2350mm |
| Iwọn Adijositabulu | 1900mm - 2500mm |
| Adijositabulu Giga | 800mm - 1050mm |
| Ibamu | Suitable for most hot tub sizes |
Alaye atilẹyin ọja
Wellis products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your purchase or visit the official Wellis webojula. Jeki ẹri rira rẹ fun awọn iṣeduro atilẹyin ọja.
Onibara Support
If you have any questions, require technical assistance, or need to order replacement parts, please contact Wellis customer support. Contact details can typically be found on the Wellis official webaaye tabi lori apoti ọja rẹ.
Fun alaye diẹ sii, ṣabẹwo: www.wellis.com