Pedrollo PKM60 Peripheral Booster Water Pump Instruction Manual

1. Ifihan

This manual provides essential information for the safe and efficient installation, operation, and maintenance of the Pedrollo PKM60 Peripheral Booster Water Pump. Please read these instructions carefully before using the pump and retain them for future reference.

The Pedrollo PKM60 pump is designed for use with clean water that does not contain abrasive particles. It is also suitable for liquids that are not chemically aggressive towards the pump's construction materials. Its reliability and ease of use make it ideal for domestic applications, including water distribution in conjunction with small pressure sets and for garden or allotment irrigation.

The pump must be installed in an enclosed environment or at least sheltered from adverse weather conditions to ensure optimal performance and longevity.

2. Alaye Aabo

Nigbagbogbo ṣe akiyesi awọn iṣọra aabo ipilẹ lati dinku eewu ina, mọnamọna, ati ipalara ti ara ẹni.

• Ensure the power supply matches the pump's specifications (127V, 60Hz).
• Disconnect power before performing any installation, maintenance, or repair work.
• Do not operate the pump with flammable or corrosive liquids.
• Dáàbò bo fifa omi kuro ninu otutu otutu ti o tutu.
• Rii daju didasilẹ to dara lati ṣe idiwọ mọnamọna.
• Jeki awọn ọmọde ati awọn oṣiṣẹ laigba aṣẹ kuro ni fifa soke lakoko iṣẹ.

3. Awọn ẹya Ọja

• Omi Iru: Omi mimọ
• Nlo: Domestic water supply systems, pressure boosting, irrigation
• Iwe afọwọkọ: Surface pump
• Idile: Peripheral pump
• Iwọn Iṣe: Flow rate up to 11 GPM, Head up to 130 ft.
• Ibi iwọn otutu olomi: -10 °C si +60 °C

4. Awọn pato

5. Eto ati fifi sori

Proper installation is crucial for the pump's performance and longevity. If you are unsure about any steps, consult a qualified professional.

5.1 Ipo

• Install the pump in a dry, well-ventilated area, protected from direct sunlight, rain, and freezing temperatures.
• Ensure adequate space around the pump for ventilation and maintenance access.
• Mount the pump on a stable, level surface to minimize vibration.

5.2 Plumbing Awọn isopọ

• Use appropriate NPT fittings for inlet and outlet connections.
• Ensure all connections are watertight to prevent air leaks, which can affect pump performance.
• Install a foot valve with a strainer on the suction line if drawing water from a well or tank to prevent debris entry and maintain prime.
• Consider installing isolation valves on both suction and discharge lines for easier maintenance.

5.3 Itanna Asopọ

• Connect the pump to a dedicated electrical circuit with appropriate overcurrent protection.
• Rii daju pe ipese agbara voltage and frequency match the pump's requirements (127V, 60Hz).
• Awọn fifa gbọdọ wa ni ilẹ daradara lati dena awọn eewu itanna.

5.4 Priming fifa soke

Ṣaaju iṣiṣẹ akọkọ, fifa naa gbọdọ wa ni titoju:

1. Yọ plug priming kuro (nigbagbogbo o wa ni oke fifa soke casing).
2. Kun fifa casing patapata pẹlu omi mimọ titi yoo fi ṣàn.
3. Rọpo plug alakoko ni aabo.
4. Open any discharge valves before starting the pump.

Nọmba 1: Pedrollo PKM60 Peripheral Booster Water Pump. This image shows the blue pump casing, the motor housing with cooling fins, and the inlet/outlet ports. A small red cap is visible on the pump body, likely indicating a priming or drain point.

6. Awọn ilana Iṣiṣẹ

Once installed and primed, operating the Pedrollo PKM60 pump is straightforward.

• Bibẹrẹ fifa soke: Ensure all connections are secure and the pump is primed. Turn on the electrical power supply to the pump. The pump should start immediately.
• Abojuto: Observe the pump during its initial operation for any unusual noises, vibrations, or leaks. Check the pressure gauge (if installed) to ensure proper system pressure.
• Idaduro fifa soke: Turn off the electrical power supply to the pump.
• Ṣiṣe gbigbe: Avoid running the pump dry, as this can cause severe damage to the mechanical seal and other components. If the pump runs dry, immediately turn off the power and re-prime it.

7. Itọju

Regular maintenance helps ensure the longevity and efficient operation of your Pedrollo PKM60 pump.

• Ayẹwo igbagbogbo: Periodically check the pump for any signs of leaks, corrosion, or damage to the casing or electrical connections.
• Ninu: Keep the pump exterior clean and free from dust and debris to ensure proper motor cooling.
• Igba otutu: If the pump is exposed to freezing temperatures, drain all water from the pump casing and pipes to prevent damage from ice expansion. Remove the drain plug (if present) and priming plug to facilitate drainage.
• Igbẹhin ẹrọ: The mechanical seal is a wear item. If persistent leaks occur from the pump shaft area, the seal may need replacement by a qualified technician.

8. Laasigbotitusita

Apá yìí ń sọ̀rọ̀ nípa àwọn ìṣòro tó wọ́pọ̀ tí o lè bá pàdé pẹ̀lú fifa omi rẹ.

9. Atilẹyin ọja ati Support

For warranty information, technical support, or spare parts, please contact your authorized Pedrollo dealer or the manufacturer directly. Keep your purchase receipt as proof of purchase.