1. Ifihan
This manual provides comprehensive instructions for the safe and efficient operation of your Helios HS4201 Electronic Digital Timer. Please read this manual thoroughly before use and retain it for future reference.
Nọmba 1: Helios HS4201 Electronic Digital Timer. This image displays the white digital timer with a standard European Type F (Schuko) socket on the front and a two-pin plug on the back. The top panel features a digital display and several control buttons.
2. Alaye Aabo
- Ensure the timer is connected to a properly grounded 220V AC power outlet.
- Do not exceed the maximum load capacity of 3500W.
- This device is rated IP20, meaning it is protected against solid objects over 12.5mm but has no protection against water. Use only in dry indoor environments.
- Má ṣe tú ẹ̀rọ náà ká tàbí gbìyànjú láti tún un ṣe. Tọ́ka gbogbo iṣẹ́ ìtọ́jú náà sí àwọn òṣìṣẹ́ tó mọ̀ nípa rẹ̀.
- Jeki kuro ni arọwọto awọn ọmọde.
3. Eto
3.1 Ibẹrẹ Agbara-soke
- Plug the Helios HS4201 timer into a standard 220V wall outlet.
- The digital display will illuminate. If the display is blank, ensure the timer is securely plugged in.
- Allow the internal battery (for memory retention) to charge for approximately 15-30 minutes before programming.
3.2 Ṣíṣeto Àkókò Lọ́wọ́lọ́wọ́
Refer to the buttons on the top panel (e.g., "CLOCK", "HOUR", "MINUTE", "DAY").
- Tẹ mọlẹ Aago bọtini.
- Nigba dani Aago, tẹ awọn OJO bọtini lati ṣeto awọn ti isiyi ọjọ ti awọn ọsẹ.
- Nigba dani Aago, tẹ awọn WAKATI bọtini lati ṣeto awọn ti isiyi wakati.
- Nigba dani Aago, tẹ awọn ISEJU bọtini lati ṣeto awọn ti isiyi iseju.
- Tu silẹ Aago Bọ́tìnì náà. Àkókò ìsinsìnyí ti ṣètò báyìí.
4. Awọn ilana Iṣiṣẹ
4.1 Programming On/Off Cycles (Up to 10 Settings)
The Helios HS4201 allows for up to 10 distinct ON/OFF programming cycles.
- Tẹ awọn PROG bọ́tìnì kan lẹ́ẹ̀kan. Ìfihàn náà yóò fi "1 ON" hàn.
- Tẹ OJO to select the day(s) for the first ON event (e.g., individual days, weekdays, weekends, all days).
- Tẹ WAKATI láti ṣètò wákàtí fún ìṣẹ̀lẹ̀ ON àkọ́kọ́.
- Tẹ ISEJU láti ṣètò ìṣẹ́jú fún ìṣẹ̀lẹ̀ ON àkọ́kọ́.
- Tẹ PROG lẹ́ẹ̀kan sí i. Ìfihàn náà yóò fi "PA 1" hàn.
- Repeat steps 2-4 to set the day(s), hour, and minute for the first OFF event.
- Tesiwaju titẹ PROG to cycle through "2 ON", "2 OFF", up to "10 ON", "10 OFF", setting each as required.
- Lẹhin ti ṣeto gbogbo awọn eto ti o fẹ, tẹ bọtini naa Aago bọtini lati jade kuro ni ipo siseto ki o pada si ifihan akoko lọwọlọwọ.
4.2 Afowoyi danu
Awọn Afọwọṣe button (or similar, check device labeling) allows you to override the programmed settings temporarily.
- Tẹ Afọwọṣe once: Switches to ON (if currently OFF) or OFF (if currently ON) until the next programmed event.
- Tẹ Afọwọṣe multiple times: Cycles through modes like AUTO ON, AUTO OFF, ON, OFF. Select AUTO ON or AUTO OFF to re-engage programmed settings.
4.3 Ṣíṣe àtúnṣe Aago náà
To clear all settings and return the timer to its factory default state, locate the small Tunto button (often recessed) and press it using a pointed object (e.g., a pen tip). The display will clear, and you will need to set the current time and reprogram all cycles.
5. Itọju
- Ninu: Yọ aago kuro ninu ibudo ina ṣaaju ki o to nu. Fi aṣọ rirọ ati gbigbẹ nu ita rẹ. Maṣe lo awọn ohun elo afọmọ omi tabi awọn ohun elo fifọ.
- Ibi ipamọ: Tọju aago naa ni itura, aye gbigbẹ nigbati ko si ni lilo.
- Batiri: The internal battery is for memory retention and is not user-replaceable. If the display frequently resets or loses settings, the internal battery may be depleted.
6. Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Ifihan jẹ òfo. | Ko si agbara. | Ensure the timer is securely plugged into a live 220V outlet. Check the circuit breaker. |
| Timer does not switch ON/OFF at programmed times. | Incorrect programming; Manual override active; Timer in OFF mode. | Review programmed settings. Press Afọwọṣe to ensure it is in AUTO ON or AUTO OFF mode. |
| Awọn eto ti sọnu lẹhin agbara outage. | Internal battery depleted or not fully charged. | Plug the timer in for 15-30 minutes to charge the internal battery. If the issue persists, the internal battery may need replacement by a service professional. |
| Connected appliance does not turn on. | Appliance fault; Timer not supplying power; Overload. | Test the appliance directly in the wall outlet. Ensure the timer is in an ON state. Verify the appliance's power consumption does not exceed 3500W. |
7. Awọn pato
- Awoṣe: HS4201
- Brand: Helios
- Voltage: 220V AC
- Ikojọpọ ti o pọju: 3500W
- Iwọn IP: IP20 (Lilo inu ile nikan)
- Eto Eto: Up to 10 ON/OFF cycles
- Awọn iwọn: 8.5 x 3.81 x 11 cm (isunmọ.)
- Ìwúwo: 2.98 Kilograms (approx.)
- Batiri ti a beere: No (Internal battery for memory retention, not user-replaceable)
8. atilẹyin ọja Information
Helios products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your purchase or contact Helios customer support. This warranty typically covers defects in materials and workmanship under normal use.
9. Onibara Support
If you encounter any issues or have questions regarding your Helios HS4201 Electronic Digital Timer that are not addressed in this manual, please contact Helios customer support. Contact details can usually be found on the product packaging or the official Helios webojula.
Please have your model number (HS4201) and purchase date available when contacting support.
