JIARUIXIN JR1922RXS-2 12V Kids Ride-On Car Remote Control and Receiver Kit Instruction Manual

Ọrọ Iṣaaju

This instruction manual provides essential information for the proper installation, operation, and maintenance of your JIARUIXIN JR1922RXS-2 12V 2.4G Bluetooth Remote Control and Receiver Kit. This kit is designed as a replacement part for specific children's powered ride-on cars. Please read this manual thoroughly before use to ensure safe and correct functionality.

Package Awọn akoonu

Package naa pẹlu awọn paati wọnyi:

• 1 x JR1922RXS-2 Control Box (12V)
• 1 x 2.4G Bluetooth Remote Control

Ṣayẹwo ibamu

To ensure this control box and remote control kit is compatible with your child's electric ride-on car, please follow these steps:

1. Open the compartment of your existing electric ride-on car where the control box is located.
2. Carefully examine the appearance and model number of your original control box.
3. If the appearance and model number (JR1922RXS-2) match your original part, this replacement kit should be compatible. The control box features a 7-pin yellow four-sided socket.

Eto ati fifi sori

1. Latọna jijin Iṣakoso batiri sori

The remote controller requires two AAA (1.5V) batteries (not included). To install the batteries:

1. Wa yara batiri ni ẹhin isakoṣo latọna jijin.
2. Lo screwdriver lati tú dabaru ati ṣi ideri batiri naa.
3. Fi awọn batiri AAA meji sii, ni idaniloju polarity ti o pe (+/-).
4. Pa ideri batiri ki o mu okun pọ.

2. Frequency Matching (Pairing)

The remote control and the vehicle's control box must be paired before first use or if the remote control batteries are replaced. This product has a memory function, so re-matching is generally not needed after battery replacement unless issues arise.

1. Ensure the remote controller has fresh batteries installed.
2. Yipada PAA the power switch on the ride-on vehicle.
3. On the remote control, simultaneously press and hold the "▲" (Forward) and "▼" (Back) keys for approximately 3 seconds. The first LED indicator on the remote will begin to flicker.
4. While the remote's LED is flickering, turn ON the power switch on the ride-on vehicle.
5. The red indicator lights on the remote control should stop flashing, indicating that the pairing process is successful.

Awọn ilana Iṣiṣẹ

Once the remote control is paired with the vehicle, you can operate the ride-on car using the following controls:

• Awọn iṣakoso gbigbe:
  • "▲" (Up Arrow): Moves the vehicle Siwaju.
  • "▼" (Down Arrow): Moves the vehicle Pada. Note: The vehicle typically operates at low speed when moving backward.
  • "◄" (Left Arrow): Turns the vehicle Osi.
  • "►" (Right Arrow): Turns the vehicle Ọtun.
• Iṣakoso iyara:
  • "S" (Speed Button): Press this button to cycle through speed settings.
    • 1 LED lit: Low speed.
    • 2 LEDs lit: Medium speed.
    • 3 LEDs lit: High speed.
• Brake/Parking:
  • "P" (Parking/Brake Button): Press and hold this key to engage the brake. All LED indicators on the remote will flicker when the brake is active.

Ipo Imurasilẹ: If the remote control is not operated for 10 seconds, it will enter standby mode. Press any key to wake it up.

Pataki: The remote controller is intended for use under adult guidance only.

Awọn pato

Laasigbotitusita

Remote Control Not Responding / Pairing Issues

• Ṣayẹwo awọn batiri: Ensure the remote control has fresh AAA batteries installed with correct polarity.
• Re-match Frequency: Follow the "Frequency Matching (Pairing)" steps in the Setup section.
• Wake from Standby: If the remote has been idle for 10 seconds, press any button to wake it up.

Interference and FCC Compliance

Ẹrọ yii ni ibamu pẹlu Apá 15 ti Awọn ofin FCC. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:

1. Ẹrọ yii le ma fa kikọlu ipalara.
2. Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa isẹ ti ko fẹ.

Akiyesi:

Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni nọmba Kilasi B, ni ibamu si Apá 15 ti Awọn ofin FCC. Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to tọ si kikọlu ipalara ni fifi sori ibugbe kan. Ẹrọ yii n ṣe ipilẹṣẹ, nlo, ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato. Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:

• Reorient tabi tun eriali gbigba pada.
• Mu iyatọ pọ si laarin ẹrọ ati olugba.
• So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ.
• Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.

Ikilọ:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Itoju

• Keep the control box and remote control dry and clean.
• Avoid exposing the components to extreme temperatures or direct sunlight.
• Tí a kò bá lo iṣakoso latọna jijin fun igba pipẹ, yọ awọn batiri kuro lati ṣe idiwọ jijo.