ELCO Lighting ELK4741 Koto System 4" Square Reflector Trim User Manual

Ọrọ Iṣaaju

Thank you for choosing the ELCO Lighting ELK4741 Koto System 4" Square Reflector Trim. This trim is designed to integrate seamlessly with compatible 4-inch recessed lighting housings, providing a clean, modern aesthetic and efficient light distribution. This manual provides essential information for safe installation, operation, and maintenance of your product.

Alaye Aabo

• IKILO: Ewu ìkọlù iná mànàmáná. Yọ agbára kúrò ní àpótí fiusi tàbí ẹ̀rọ ìfọ́mọ́ra kí o tó fi sori ẹrọ tàbí ṣe àtúnṣe.
• Installation should be performed by a qualified electrician in accordance with all local electrical codes and ordinances.
• Rii daju voltage supply is compatible with the recessed housing and light source being used.
• Do not install this trim in locations where it may be exposed to direct water spray unless the associated recessed housing is also rated for such conditions. This trim is rated for wet locations when used with an appropriately rated housing.
• Handle the trim with care to avoid damage to the finish or reflector.

Package Awọn akoonu

Daju pe gbogbo awọn paati wa ṣaaju ki o to bẹrẹ fifi sori:

• ELCO Lighting ELK4741 Koto System 4" Square Reflector Trim (1 unit)

Image showing the ELCO Lighting ELK4741 Koto System 4 inch Square Reflector Trim, a white square trim designed for recessed lighting fixtures.

Eto ati fifi sori

This trim is designed for flush mount, ceiling mount installation with a compatible 4-inch recessed housing (sold separately). No assembly is required for the trim itself.

1. Pa Agbara: Before starting, ensure the power to the circuit where the recessed light will be installed is turned off at the circuit breaker or fuse box.
2. Prepare Housing: Install the compatible 4-inch recessed lighting housing according to its specific instructions. Ensure all electrical connections are secure and properly insulated.
3. Fi Orisun Imọlẹ sori ẹrọ: Insert the appropriate GX53 base LED light source into the recessed housing socket.
4. Fi sori ẹrọ Trim: Align the ELK4741 trim with the recessed housing opening. Gently push the trim upwards until its retention clips engage with the housing, securing it flush against the ceiling. Ensure the trim is seated evenly.
5. Pada Agbara pada: Once the trim is securely installed, restore power to the circuit.

Awọn ilana Iṣiṣẹ

The ELK4741 trim itself does not have operational controls. Its function is to provide a finished appearance and direct light from the installed light source. The operation of the light fixture (on/off, dimming) is controlled by the wall switch or dimmer connected to the recessed housing circuit.

Itoju

To maintain the appearance and performance of your ELK4741 trim:

• Ninu: Ensure power is off before cleaning. Wipe the trim with a soft, dry, or slightly damp Aṣọ. Má ṣe lo àwọn ohun ìfọṣọ, àwọn ohun èlò ìfọṣọ, tàbí àwọn ohun ìfọṣọ, nítorí pé wọ́n lè ba ìparí rẹ̀ jẹ́.
• Rirọpo Boolubu: If the light source needs replacement, turn off power at the circuit breaker. Carefully remove the trim by gently pulling it down from the ceiling. Replace the GX53 LED bulb, then re-install the trim as per the installation instructions.

Laasigbotitusita

If the light fixture is not functioning after trim installation, consider the following:

• Ko si Imọlẹ:
  • Ṣayẹwo ti o ba ti Circuit fifọ ti wa ni tripped tabi ti o ba ti fiusi ti wa ni ti fẹ.
  • Rí i dájú pé ìyípadà ògiri wà ní ipò 'ON'.
  • Verify that the light source (bulb) is correctly seated in the socket and is not faulty.
  • Confirm that the recessed housing is properly wired and receiving power.
• Trim Not Flush:
  • Ensure the retention clips are fully engaged with the recessed housing.
  • Check for any obstructions preventing the trim from seating correctly.

Ti awọn iṣoro ba tẹsiwaju, kan si onisẹ ina mọnamọna to peye.

Awọn pato

Atilẹyin ọja ati Support

This ELCO Lighting product is covered by a 5-odun lopin atilẹyin ọja. Atilẹyin ọja yi ni wiwa awọn abawọn ninu awọn ohun elo ati iṣẹ-ṣiṣe labẹ lilo deede ati iṣẹ.

For warranty claims, technical support, or further assistance, please contact ELCO Lighting customer service or visit their official website. Please have your model number (ELK4741) and proof of purchase available.

Imọlẹ ELCO Webojula: www.elcolighting.com