Ọrọ Iṣaaju
Thank you for choosing the ErGear Dual Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your new monitor mount. Please read this manual thoroughly before installation and keep it for future reference.
Alaye Aabo pataki
Please ensure all instructions are read and understood before assembly and use. If you have any questions, please contact customer service. Failure to follow these instructions may result in property damage, serious injury, or death.
- Verify that your monitor's weight and VESA pattern are within the specified limits.
- Do not exceed the maximum load capacity of 26.5 lbs per arm.
- Ensure the mounting surface (desk) is strong enough to support the combined weight of the mount and monitors.
- Lo ohun elo ti a pese nikan.
- Pa awọn ẹya kekere kuro lati ọdọ awọn ọmọde.
Awọn pato
- Awoṣe: EGCM13B
- Ibamu Iwọn iboju: 13 to 34 inches
- Weight Capacity (per arm): Titi di 26.5 lbs
- Ibamu VESA: 75x75 mm, 100x100 mm
- Arm Span: 33 inches
- Giga Ọpá: 16.3 inches
- Iru gbigbe: Tilt, Swivel, Rotation, Articulating
- Igun Tita ti o pọju: Awọn iwọn 90
- Ohun elo: Alloy Irin
- Àwọ̀: Dudu
- Iru fifi sori: Ìdúró Tábìlì (C-Cl)amp tabi Grommet)
- C-Clamp Sisanra Iduro: 0.39"-3.15"
- Grommet Mount Desk Thickness: 0.39"-2.17"
- Grommet Hole Diameter: 0.47"-0.79"
Package Awọn akoonu
Please check that all parts are included and undamaged. If any parts are missing or damaged, please contact customer service.
- Main Pole with Desk Clamp/Grommet Base
- Meji Monitor Arms
- Àwọn àwo VESA (2x)
- Mounting Hardware (screws, washers, tools)
- Clips Management Clips
- Ilana itọnisọna
Eto ati fifi sori
1. Desk Compatibility Check
Before installation, ensure your desk meets the following criteria:
- Ohun elo: Recommended for wooden tables.
- Labẹ: Preferably free of beams or panels that may interfere with installation.
- C-Clamp Sisanra: 0.39"-3.15"
- Grommet Mount Thickness: 0.39" - 2.17" (Hole Diameter: 0.47" - 0.79")
2. Monitor Compatibility Check
Each monitor must meet these conditions:
- Iwọn iboju: 13 to 34 inches
- Ìwúwo: Titi di 26.5 lbs
- Awọn iho Iṣagbesori VESA: 75x75 mm or 100x100 mm apart on the back of the monitor.
3. Assemble the Pole with Clamp Atilẹyin
Choose either C-Clamp or Grommet installation based on your desk type.
Follow the detailed steps in the provided video and diagrams to securely attach the main pole to your desk using either the C-Clamp or Grommet method. Ensure all screws are tightened appropriately for stability.
4. Assemble the Arm and Pole Wire Clips
Attach the monitor arms to the main pole. Loosen the screw on the pipe clamp before installing the arm, then tighten it securely. Ensure the VESA plate side of the arm faces upwards. Install the cable management clips along the arms and pole.
5. Assemble VESA Plate and Monitor
Attach the VESA plate to the back of your monitor using the appropriate screws and washers. Ensure it is securely fastened.
6. Install the Monitor to the Swivel Arm
Carefully slide the monitor (with the attached VESA plate) onto the swivel arm. Secure it by tightening the locking screw. Adjust the screw with the Allen key to adjust the height of the VESA panel as needed (clockwise to lower, counter-clockwise to raise).
Ṣiṣẹ ati Awọn atunṣe
The ErGear Dual Monitor Desk Mount offers versatile adjustments for optimal viewitunu:
- Atunse Giga: tú awọn clamp on the main pole to slide the arms up or down to your desired height. Re-tighten the clamp ni aabo.
- Tẹ: Adjust the monitor's vertical angle by tilting it +/-45 degrees to reduce glare and eye strain.
- Swivel: Rotate the monitor horizontally +/-90 degrees for easy screen sharing or viewing lati orisirisi awọn agbekale.
- Yiyi: Yi atẹle naa ni iwọn 360 lati yipada laarin ala-ilẹ ati awọn iṣalaye aworan.
- Arm Extension/Retraction: The articulating arms allow you to extend or retract your monitors closer or further from you. Adjust the tension screws on the arm joints as needed to hold the desired position.
Itoju
- Lokọọkan ṣayẹwo gbogbo awọn skru ati awọn asopọ lati rii daju pe wọn wa ni wiwọ ati aabo.
- Nu òke pẹlu asọ, damp asọ. Yago fun abrasive ose.
- Do not disassemble the mount unless instructed to do so.
Laasigbotitusita
- Awọn diigi kii ṣe ipele: Ensure the VESA plates are correctly aligned and tightened. Adjust the small bolts on the tilt head to fine-tune alignment.
- Monitors sag or do not hold position: Tighten the tension screws on the arm joints. Refer to the assembly instructions for specific locations.
- Òkè kan rí àìdúróṣinṣin: Double-check that the C-Clamp or Grommet mount is securely fastened to the desk and all screws are fully tightened. Ensure your desk meets the thickness requirements.
Atilẹyin ọja ati Support
For warranty information or technical support, please refer to the product packaging or contact ErGear customer service directly. Keep your purchase receipt as proof of purchase.
