TFA Dostmann Wireless Weather Station Clear 35.1168.02 User Manual
Model: 35.1168.02 | Brand: TFA Dostmann
1. Ifihan
This manual provides detailed instructions for the setup, operation, and maintenance of your TFA Dostmann Clear 35.1168.02 Wireless Weather Station. Please read this manual thoroughly before using the device to ensure correct operation and to prevent damage.
The weather station monitors indoor and outdoor temperature and humidity, and provides a weather forecast based on atmospheric pressure changes.
2. Alaye Aabo
- Jeki ẹrọ ati awọn batiri kuro ni arọwọto awọn ọmọde.
- Ma ṣe fi ẹrọ naa han si awọn iwọn otutu to gaju, gbigbọn, tabi awọn ipaya.
- Yago fun orun taara ati ọrinrin.
- Maṣe fi ẹrọ naa bọ inu omi.
- Use only specified batteries. Ensure correct polarity.
- Replace all batteries simultaneously.
- Dispose of depleted batteries and the device according to local regulations.
- The outdoor sensor should be placed in a sheltered location, protected from direct precipitation.
3. Package Awọn akoonu
- Base Station (Weather Station)
- Thermo-Hygrometer Outdoor Sensor (Model: 30.3256.02)
- Itọsọna olumulo
Note: 4 x 1.5V AAA batteries (2 for base station, 2 for outdoor sensor) are required and not included.
4. Ọja Ipariview
Figure 1: TFA Dostmann Clear 35.1168.02 Wireless Weather Station (Base Unit and Outdoor Sensor).
This image displays the main weather station unit on the right, showing its digital display with atmospheric pressure, weather icons, outdoor temperature and humidity, and indoor temperature and humidity. To the left is the compact outdoor sensor, also displaying temperature and humidity.
4.1 Base Station Display Elements
Figure 2: Close-up of the Weather Station Display.
The display shows: atmospheric pressure (hPa), weather forecast icons (sunny, partly cloudy, cloudy, rainy), outdoor channel indicator (CH 1 OUT), outdoor temperature (°C/°F) and humidity (%), and indoor temperature (°C/°F) and humidity (%).
- Atẹgun Ayika: Displayed in hPa, with trend arrows.
- Awọn aami asọtẹlẹ oju-ọjọ: 4 symbols (sunny, partly cloudy, cloudy, rainy) based on pressure changes.
- Iwọn otutu ita gbangba & Ọriniinitutu: From the wireless sensor.
- Iwọn inu ile & Ọriniinitutu: Measured by the base station.
- Ifihan ikanni: Shows which outdoor sensor channel is currently displayed (up to 3 sensors supported).
4.2 Base Station Control Buttons (Rear)
Figure 3: Rear of the Base Station showing control buttons and battery compartment.
The rear panel features four control buttons: DOWN, UP, CHANNEL, and SET. These buttons are used for navigating settings, adjusting values, and switching between outdoor sensor channels.
- NIPA: Decreases values, navigates menus.
- Soke: Increases values, navigates menus.
- Ikanni: Switches between outdoor sensor channels (if multiple sensors are paired).
- Ṣeto: Enters settings mode, confirms selections.
5. Eto
5.1 Fifi sori batiri
- Sensọ ita gbangba: Open the battery compartment on the back of the outdoor sensor. Insert 2 x 1.5V AAA batteries, observing correct polarity (+/-). Close the compartment.
- Ibudo Ipilẹ: Open the battery compartment on the back of the base station. Insert 2 x 1.5V AAA batteries, observing correct polarity (+/-). Close the compartment.
- The base station will emit a short beep and all LCD segments will light up briefly. It will then display indoor temperature and humidity. The outdoor sensor data will appear shortly after.
5.2 Ìsopọ̀ Sensọ
The base station will automatically attempt to connect to the outdoor sensor upon battery insertion. Ensure the sensor is within range (max. 100m in open air). If connection is not established, press the "CHANNEL" button on the base station to initiate a manual search.
The station supports up to three outdoor sensors. To add additional sensors, repeat the battery installation process for each new sensor. Use the "CHANNEL" button to cycle through and display data from different sensors.
5.3 Initial Settings (Atmospheric Pressure)
The atmospheric pressure needs to be set during initial setup for accurate weather forecasting. Consult a local weather service or online source for the current atmospheric pressure in your area.
- Press and hold the "SET" button until the atmospheric pressure value flashes.
- Use the "UP" or "DOWN" buttons to adjust the value to your local atmospheric pressure.
- Press "SET" again to confirm and exit the setting mode.
5.4 Ibi
- Ibudo Ipilẹ: Place the base station indoors on a flat surface or mount it on a wall. Avoid placing it near heat sources, direct sunlight, or areas with high electromagnetic interference.
- Sensọ ita gbangba: Position the outdoor sensor in a sheltered location, protected from direct rain and snow. Ensure good air circulation around the sensor. Avoid direct sunlight to prevent inaccurate temperature readings. The maximum range is 100m (open field).
6. Ṣiṣẹ Ibusọ Oju-ọjọ
6.1 Displaying Temperature and Humidity
The base station continuously displays indoor temperature and humidity, along with the selected outdoor sensor's temperature and humidity.
6.2 Yipada Awọn iwọn otutu (°C/°F)
To switch between Celsius and Fahrenheit, briefly press the "UP" button outside of setting mode.
6.3 Asọtẹlẹ Oju -ọjọ
The weather station provides a forecast for the next 12-24 hours using four weather icons: sunny, partly cloudy, cloudy, and rainy. These forecasts are based on changes in atmospheric pressure. The accuracy of the forecast improves after the initial atmospheric pressure setting has been stable for several hours.
6.4 Atmospheric Pressure Trend
Arrows next to the atmospheric pressure display indicate whether the pressure has risen, fallen, or remained stable over the last hour. This helps in understanding short-term weather trends.
7. Itọju
7.1 Ninu
Nu ẹrọ naa pẹlu asọ, damp asọ. Ma ṣe lo abrasive ose tabi epo. Rii daju pe ko si ọrinrin wọ inu ẹrọ naa.
7.2 Batiri Rirọpo
Replace batteries when the low battery indicator appears on the display. Always replace all batteries in a unit (base station or sensor) simultaneously to ensure optimal performance. Dispose of old batteries responsibly.
8. Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Ko si ifihan iwọn otutu/ọriniinitutu ita gbangba. |
|
|
| Inaccurate weather forecast. |
|
|
| Ifihan ti wa ni baibai tabi òfo. |
|
|
9. Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Nọmba awoṣe | 35.1168.02 |
| Ibiti Igba otutu Ita gbangba | -20 ° C si +60 ° C (-4 ° F si +140 ° F) |
| Ibiti Igba otutu Ile | -10°C si +50°C (+14°F si +122°F) |
| Abe ile ọriniinitutu Range | 20% si 95% ọriniinitutu ojulumo |
| Ohun elo | Ṣiṣu |
| Maximum Range (Outdoor Sensor) | 100 m (aaye ṣiṣi) |
| Included Transmitter Model | 30.3256.02 (Max. 3 transmitters supported) |
| Igbohunsafẹfẹ gbigbe | 433 MHz |
| Iṣagbesori Aw | Table lawujọ tabi odi ikele |
| Power Supply (Batteries) | Base Station: 2 x 1.5V AAA (not included) Outdoor Sensor: 2 x 1.5V AAA (not included) |
| Awọn iwọn (L x W x H) | 94 x 20 (58) x 105 (101) mm |
| Iwọn | 109 g |
10. Atilẹyin ọja ati Support
TFA Dostmann products are manufactured with quality and precision. For warranty information and technical support, please refer to the official TFA Dostmann webaaye tabi kan si olupin agbegbe rẹ. Tọju iwe-ẹri rira rẹ bi ẹri rira.
Spare parts availability: 1 Year.
Olupese: TFA Dostmann
Orilẹ-ede ti Oti: China
