YUHANUS 125KHZ RFID ID Cards Keypad Panel User Manual

1. Ifihan

The YUHANUS 125KHZ RFID ID Cards Keypad Panel is a robust access control system designed for secure entry management. It supports up to 1000 user cards and a unique PIN, offering multiple access methods including ID card, PIN, or a combination of both. Constructed from fire-resistant ABS material, this keypad ensures durability and safety. It features full programming directly from the keypad, an anti-tamper alarm, and supports an external doorbell chime. This manual provides detailed instructions for installation, operation, and maintenance.

2. Alaye Aabo

• Ka gbogbo awọn ilana ni pẹkipẹki ṣaaju fifi sori ẹrọ ati ṣiṣẹ.
• Ensure power is disconnected before wiring to prevent electrical shock.
• This device is designed for indoor use or protected outdoor environments. Avoid direct exposure to water or extreme weather conditions.
• Only use the specified power supply (DC 12V).
• Má ṣe gbìyànjú láti tú tàbí tún ẹ̀rọ náà ṣe fúnra rẹ. Pe àwọn òṣìṣẹ́ tó mọ̀ nípa iṣẹ́ náà fún iṣẹ́ náà.

3. Package Awọn akoonu

• 1x YUHANUS 125KHZ RFID ID Keypad Panel
• 10x 125KHZ ID Keyfobs
• Iṣagbesori skru ati Wall Plugs
• Afowoyi Olumulo (iwe-ipamọ yii)

Image: Included 125KHZ ID Keyfobs

4. Ọja Ipariview

The keypad panel features a numeric keypad, status indicator LEDs, and a doorbell button. The rear panel includes wiring terminals and an anti-tamper yipada.

Aworan: Iwaju view of the Keypad Panel

Image: Keypad Panel with External Doorbell Connection

Image: Anti-Tamper Switch (Internal)

5. Awọn pato

Àwòrán: Ìwọ̀n Ọjà

6. Eto

6.1 Iṣagbesori

1. Choose a suitable mounting location, typically near the door to be controlled. Ensure it is protected from direct weather exposure if installed outdoors.
2. Mark the drilling points for the mounting screws using the backplate as a template.
3. Lu ihò ki o si fi ogiri plugs ti o ba wulo.
4. Ṣe aabo awọn apoeyin si odi.

6.2 Onirin

Pataki: Disconnect all power before performing any wiring connections.

Image: Wiring Terminal Block

Image: Wiring Diagram of the Access Control System

Refer to the wiring diagram above and the terminal block image for connections. Common connections include:

• +12V ati GND: Connect to a DC 12V power supply.
• NO/PUSH, COM, NC: Connect to your electric lock (e.g., magnetic lock, electric strike).
• ṢII: Connect to an exit button.
• BELL, BELL: Connect to an external doorbell chime.

6.3 Ibẹrẹ Agbara-soke

1. After completing all wiring, apply DC 12V power to the unit.
2. The keypad will emit a beep, and the indicator lights will flash, indicating successful power-up.
3. The default Master Code is typically 123456. It is highly recommended to change this immediately after initial setup.

7. Awọn ilana Iṣiṣẹ

7.1 Eto Ipo

To enter programming mode: Press * then enter the Master Code (default: 123456) then press #. The red LED will illuminate.

To exit programming mode: Press *. The red LED will turn off.

7.2 Yi koodu titunto si

1. Tẹ Ipo siseto.
2. Tẹ 0.
3. Enter your new 6-digit Master Code.
4. Tẹ # lati jẹrisi.
5. Jade Ipo siseto.

7.3 Adding User Cards/PINs

The system supports up to 1000 users.

1. Tẹ Ipo siseto.
2. Tẹ 1 to add a user.
3. For Card Only Access: Present the ID card to the keypad. The keypad will beep, and the card is added.
4. For PIN Only Access: Enter a 4-6 digit PIN, then press #. Repeat the PIN and press # lẹẹkansi lati jẹrisi.
5. For Card + PIN Access: Present the ID card, then enter a 4-6 digit PIN, then press #. Repeat the PIN and press # lẹẹkansi lati jẹrisi.
6. To add more users, repeat step 3 or 4.
7. Jade Ipo siseto.

7.4 Deleting User Cards/PINs

1. Tẹ Ipo siseto.
2. Tẹ 2 to delete a user.
3. To Delete by Card: Present the ID card to the keypad. The keypad will beep, and the card is deleted.
4. To Delete by PIN: Enter the 4-6 digit PIN, then press #.
5. To delete more users, repeat step 3 or 4.
6. Jade Ipo siseto.

7.5 Wíwọlé sí ẹnu ọ̀nà

Image: User Interacting with Keypad

• Card Only: Present your registered ID card to the keypad. The green LED will flash, and the door will unlock.
• PIN Only: Enter your registered 4-6 digit PIN, then press #. The green LED will flash, and the door will unlock.
• Card + PIN: Present your registered ID card, then enter your 4-6 digit PIN, then press #. The green LED will flash, and the door will unlock.

7.6 Doorbell Function

Press the doorbell button (bell icon) on the keypad to activate the external doorbell chime (if connected).

Image: Doorbell Button

7.7 Anti-Tamper Itaniji

If the keypad is forcibly removed from its mounting location, the built-in anti-tamper switch will trigger a loud alarm. To silence the alarm, re-secure the keypad or enter the Master Code.

8. Itọju

• Clean the keypad surface with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Nigbagbogbo ṣayẹwo awọn asopọ onirin fun eyikeyi ami ti wọ tabi ibaje.
• Ensure the keypad is securely mounted to prevent accidental tampsisun.

9. Laasigbotitusita

• Bọtini bọtini ko dahun: Check power supply connections. Ensure DC 12V is correctly applied.
• Door does not unlock:
  • Verify the ID card or PIN is correctly registered.
  • Check wiring to the electric lock. Ensure COM, NO/PUSH, NC connections are correct for your lock type.
  • Confirm the power supply is adequate for both the keypad and the lock.
• Anti-tamper alarm triggers unexpectedly: Ensure the keypad is firmly attached to its mounting surface and the anti-tamper switch is properly engaged.
• Cannot enter programming mode: Double-check the Master Code. If forgotten, a factory reset may be required (refer to advanced programming instructions, not covered in this basic manual).

10. Atilẹyin ọja ati Support

Fun alaye atilẹyin ọja tabi atilẹyin imọ ẹrọ, jọwọ kan si alagbata rẹ tabi olupese taara. Tọju iwe-ẹri rira rẹ bi ẹri rira.