Ọrọ Iṣaaju
This manual provides essential information for the installation, operation, and maintenance of your replacement water drain pump, designed for compatibility with Kenmore Washer Model 110.26832692. Please read these instructions carefully before proceeding with installation or use to ensure proper function and safety.
Alaye Aabo
Always observe the following safety precautions when handling or installing the drain pump:
- Ge Agbara: Before beginning any installation or maintenance, ensure the washer is unplugged from the electrical outlet to prevent electric shock.
- Ipade Omi: Turn off the water supply to the washer to prevent leaks.
- Wọ Ohun elo Idaabobo: Use appropriate personal protective equipment, such as gloves and eye protection, to avoid injury.
- Sisan omi ti o kù: Be prepared for residual water in the washer and hoses. Have towels and a bucket ready.
- Iranlọwọ Ọjọgbọn: Ti o ko ba ni idaniloju nipa igbesẹ eyikeyi, kan si onimọ-ẹrọ ohun elo ti o peye.
Package Awọn akoonu
package rẹ yẹ ki o ni nkan wọnyi ninu:
- 1 x Washer Water Drain Pump (Replacement Part)
Awọn ilana fifi sori ẹrọ
Follow these steps carefully to replace the water drain pump in your Kenmore 110.26832692 washer. Refer to your washer's specific service manual for detailed diagrams if necessary.
- Prepare the Washer: Disconnect the washer from its power source and turn off the water supply. Pull the washer away from the wall to access the rear.
- Wọle si Pump naa: Depending on your specific Kenmore 110.26832692 model, you may need to remove the front panel, rear panel, or tilt the washer back to access the drain pump located at the bottom. Consult your washer's service manual for exact access procedures.
- Sisan omi ti o kù: Place a shallow pan or towels under the pump area to catch any remaining water in the hoses. Carefully disconnect the hoses attached to the old drain pump.
- Yọ Pump atijọ kuro: Locate the mounting screws or clips securing the old drain pump. Remove them and carefully detach the pump from its mounting bracket. Disconnect any electrical wiring connected to the pump.
- Fi Pump Tuntun sori ẹrọ: Connect the electrical wiring to the new drain pump. Ensure connections are secure. Mount the new pump onto the bracket using the original screws or clips.
- Awọn ọna asopọ: Reattach the drain hoses to the new pump. Ensure all clamps ti wa ni tightened lati se jo.
- Atun-ifọṣọ: Reinstall any panels or covers that were removed to access the pump.
- Iṣiṣẹ Idanwo: Reconnect the washer to the power supply and turn on the water. Run a short drain/spin cycle to check for proper operation and any leaks.
Awọn Ilana Iṣiṣẹ
The water drain pump is an integral component of your washing machine's drainage system. During the wash and rinse cycles, once the water needs to be expelled from the tub, the washer's control system activates the drain pump. The pump then draws water from the washer tub and forces it through the drain hose, effectively emptying the machine. Proper functioning of this pump ensures that water is removed efficiently, allowing the spin cycle to effectively remove moisture from your laundry.
Itoju
To ensure the longevity and efficient operation of your drain pump, consider the following maintenance tips:
- Ninu igbagbogbo: Periodically check the washer's drain filter (if accessible and present in your model) for lint, coins, or other debris that could obstruct the pump.
- Yago fun ikojọpọ pupọ: Ikojọpọ apẹja le fi wahala ti ko yẹ sori fifa soke ati awọn paati miiran.
- Ṣayẹwo Awọn okun: Occasionally inspect the drain hoses for kinks, blockages, or damage that could impede water flow.
Laasigbotitusita
If your washer is experiencing drainage issues after pump replacement, refer to the table below for common problems and potential solutions:
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Ẹ̀rọ fifọ aṣọ kò ń gbẹ omi |
|
|
| Ariwo ti npariwo lakoko iyipo sisan |
|
|
| Omi jijo lati agbegbe fifa |
|
|
Tí àwọn ìgbésẹ̀ láti yanjú ìṣòro náà kò bá yanjú ìṣòro náà, a gbani nímọ̀ràn láti kan sí onímọ̀ ẹ̀rọ tó mọṣẹ́ nípa àtúnṣe ẹ̀rọ náà.
Awọn pato
- Iru ọja: Washer Water Drain Pump (Replacement Part)
- Ibamu: Kenmore Washer Model 110.26832692
- Olupese: 20 SECOND SOAP (Supplier of this replacement part)
- UPC: 689035815232
- ASIN: B0DBGGY267
Atilẹyin ọja ati Support
For information regarding the warranty of this replacement part or for technical support, please refer to the documentation provided by the seller or manufacturer at the time of purchase. You may also contact the seller directly through the platform where the purchase was made.
