SYNCO XTalk XPro2 2.4GHz Wireless Intercom Headset System

1. Ifihan

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your SYNCO XTalk XPro2 2.4GHz Wireless Intercom Headset System. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.

Figure 1: SYNCO XTalk XPro2 Headset System and Accessories

2. Ọja Ipariview

The SYNCO XTalk XPro2 is a full-duplex wireless intercom headset system designed for professional team communication. Key features include:

• Gbigba ifihan agbara ti o ni ilọsiwaju: External antennas provide a reliable 500m (1640ft) connection range.
• Ilọsiwaju Ariwo Idinku: Features 2.0 AEC algorithm (150Hz to 7KHz) for clear voice recognition in noisy environments.
• Flexible Team Communication: Supports up to 13-unit connections with group expansion technology.
• Ipo Igbegasoke: Enhances signal strength for stable communication through obstacles.
• Ipo Olokiki: One-button remote muting function for the Master headset.
• Igbesi aye batiri gigun: Over 24 hours of use with rechargeable and replaceable batteries.
• Abojuto Igba-gidi: 3.5mm monitoring jack for simultaneous communication and device audio monitoring.

Figure 2: Enhanced Signal Reception

Figure 3: Advanced AEC Noise Reduction

3. Eto

3.1 Manual Pairing

Follow these steps to manually pair your headsets:

1. Agbara lori gbogbo awọn agbekọri.
2. Set one headset as the Master and the others as Level 1.
3. Within 1 minute, long press all 'A' buttons. Release after the first beep. You will hear "Pairing Succeed".
4. Restart all headsets.

3.2 Using SYNCO EasyGo Software

For quick firmware upgrades, voice pack installations, and headset pairing, use the SYNCO EasyGo software. Refer to the user guide for software download and usage instructions from the SYNCO official site.

Figure 4: SYNCO EasyGo Software Interface

4. Awọn ilana Iṣiṣẹ

4.1 Iwọn didun Eto

Short press the volume '+' or '-' buttons on the headset to adjust the listening volume.

4.2 Mute/Unmute Microphone

To mute or unmute the microphone, rotate the boom arm up or down. Rotating it up mutes the microphone, and rotating it down unmutes it.

4.3 Ariwo Ifagile

Short press button 'B' to toggle noise cancellation on or off. You will hear a beep to confirm the change.

4.4 Dominant Mode

Press and hold button 'B' to enter Dominant Mode. This mode allows the Master headset to mute all remote headsets instantly. Release the button to exit Dominant Mode.

4.5 Igbelaruge Ipo

Long press the volume '-' button to hear a "beep", then release to switch between Mode 1, Mode 2, and Mode 3. Mode 2 is the default. Boost Mode enhances signal strength for stable communication, especially through obstacles.

4.6 Real-Time Abojuto

Connect the headset to a device (e.g., camera, recorder) via the 3.5mm TRS port for real-time audio monitoring. This port is for monitoring only and does not output audio.

Figure 5: Real-Time Monitoring Setup

5. Awọn itọkasi

The LED indicator on the microphone boom arm provides status information:

• Iduroṣinṣin Imọlẹ Alawọ ewe: Sisopọ Aṣeyọri
• Green Light Flashing Slow: Ko Sopọ
• Green/Yellow Lights Alternating: Ifagile Ariwo Pa
• Red Light Flashing Slow: Batiri kekere
• Imọlẹ Pupa Duro: Gbigba agbara

6. Itọju

To ensure the longevity and optimal performance of your SYNCO XTalk XPro2 headset system, follow these maintenance guidelines:

• Ninu: Lo asọ ti o rọ, ti o gbẹ lati nu agbekari naa. Yago fun lilo awọn kẹmika lile tabi awọn ohun elo abrasive.
• Ibi ipamọ: Tọju agbekari naa ni itura, aye gbigbẹ kuro lati orun taara ati awọn iwọn otutu to gaju.
• Itọju Batiri: The system uses rechargeable and replaceable Lithium-Ion batteries. Ensure batteries are fully charged before extended use and stored properly if not used for long periods.
• Idaabobo Gbohungbohun: Keep the microphone foam cover clean and replace if damaged to maintain audio quality.

Figure 6: 24-Hour Battery Life

7. Laasigbotitusita

If you encounter issues with your SYNCO XTalk XPro2 system, refer to the following common problems and solutions:

• No Audio/Intermittent Connection:
  • Ensure all headsets are powered on and fully charged.
  • Verify proper pairing between Master and Level 1 headsets (refer to Section 3.1).
  • Check the operating range; move closer to the Master headset.
  • Restart all headsets.
• Didara Ohun Ti Ko Dara/Ariwo Ju Lo:
  • Ensure Noise Cancellation is activated (refer to Section 4.3).
  • Check microphone position and ensure it is not obstructed.
  • Verify that the microphone boom arm is fully down for unmuted operation.
• Agbekọri Ko Ngba agbara:
  • Rii daju pe okun gbigba agbara ti sopọ ni aabo si agbekari mejeeji ati orisun agbara.
  • Ṣayẹwo orisun agbara fun iṣẹ ṣiṣe.
  • Verify the charging indicator (Red Light Steady) as per Section 5.

8. Awọn pato

9. Atilẹyin ọja ati Support

For warranty information, technical support, or service inquiries, please refer to the official SYNCO webojula tabi kan si wọn onibara iṣẹ taara. Tọju iwe-ẹri rira rẹ bi ẹri rira fun awọn iṣeduro atilẹyin ọja.