1. Ọja Ipariview
This manual provides instructions for the installation and maintenance of the Hooke Road Flux Tube Fender Flares Kit, designed specifically for Jeep Gladiator JT models from 2020 to 2025. These fender flares are engineered to enhance vehicle protection and appearance, offering increased tire clearance and defense against trail debris.
Aworan 1.1: Pariview of the Hooke Road Flux Tube Fender Flares Kit, showing both installed and individual components.
2. Package Awọn akoonu
Rii daju pe gbogbo awọn paati wa ṣaaju ki o to bẹrẹ fifi sori ẹrọ.
- 4 × Fender Flares (2 Front, 2 Rear - Passenger and Driver Sides)
- Iṣagbesori Hardware Kit
- Ilana fifi sori ẹrọ
Image 2.1: Front Fender Flares.
Image 2.2: Rear Fender Flares.
3. Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Ohun elo | 2020-2025 Jeep Gladiator JT |
| Ohun elo | 1.5" diameter × 0.06" thick steel tube, 16-gauge (1/16 inch) and 11-gauge (1/8 inch) steel plate |
| Pari | Textured black powder coat with E-coating process |
| Front Fender Width | 6.6 inches |
| Rear Fender Width | 5.7 inches |
| Imọlẹ Ijọpọ | Amber turn signal lights (front flares) |
| Isunmọ iwuwo | 75 lbs |
| Nọmba awoṣe | BXG.7021AB-1 |
Image 3.1: Construction details of the fender flares, showing steel tube and plate components.
Image 3.2: Two-stage finish for corrosion resistance, including E-coat and textured black powder coat.
Image 3.3: Fender flare width measurements.
4. Awọn ilana fifi sori ẹrọ
Professional installation is recommended. Ensure the vehicle is parked on a level surface with the engine off and parking brake engaged. Disconnect the vehicle's battery before starting any electrical work.
- Igbaradi: Remove the factory fender flares and the existing inner fender liners from your Jeep Gladiator JT.
- Ipo: Carefully position the new Hooke Road Flux Tube Fender Flares onto the vehicle. Ensure proper alignment with the mounting points.
- Iṣagbesori to ni aabo: Use the provided mounting hardware to bolt the fender flares into place. A hand rivet nut tool is included for inserting rivet nuts into designated mounting holes. Tighten all bolts securely, but do not overtighten.
- Wiring for Turn Signals (Front Flares Only): The front fender flares are equipped with amber turn signal lights. Connect the wiring for these lights to your vehicle's existing turn signal circuit. Consult your vehicle's service manual for specific wiring diagrams if needed. Ensure all connections are secure and properly insulated.
- Inner Fender Liners: These fender flares are designed to fit perfectly with Hooke Road inner fender liners (sold separately). If using aftermarket or factory inner fender liners, ensure they do not interfere with the new flares.
- Ṣayẹwo Ipari: After installation, verify that all flares are securely attached and that the turn signal lights function correctly.
Image 4.1: Front fender flare with integrated amber turn signal light.
Image 4.2: Front fender flare installed.
Image 4.3: Rear fender flare installed.
5. Isẹ
The primary function of these fender flares is to provide increased tire clearance and protection. The front fender flares include integrated amber turn signal lights. These lights operate in conjunction with your vehicle's existing turn signal system once properly wired during installation.
- Turn Signal Activation: The amber lights will activate when the vehicle's turn signals are engaged, providing additional visibility.
- Off-Road Clearance: The upward-angled design increases tire clearance, which is beneficial for off-road articulation and accommodating larger tires.
Image 5.1: Increased tire clearance provided by the fender flares.
6. Itọju
To ensure the longevity and appearance of your Hooke Road Flux Tube Fender Flares, follow these maintenance guidelines:
- Ninu igbagbogbo: Clean the fender flares regularly with mild soap and water to remove dirt, mud, and road grime. Avoid abrasive cleaners or harsh chemicals that could damage the powder coat finish.
- Ṣayẹwo fun ibajẹ: Periodically inspect the flares for any signs of damage, such as chips, scratches, or dents, especially after off-road use. Touch up any damaged areas of the powder coat to prevent rust.
- Ṣayẹwo Awọn ohun elo: Regularly check all mounting bolts and fasteners to ensure they remain tight. Vibrations from driving, especially off-road, can cause fasteners to loosen over time.
- Awọn Isopọ Itanna: For the front turn signal lights, periodically inspect the wiring connections for corrosion or damage. Ensure they remain secure and waterproof.
7. Laasigbotitusita
Ti o ba pade awọn iṣoro lakoko tabi lẹhin fifi sori ẹrọ, ronu awọn atẹle:
- Flares Not Fitting Correctly: Double-check that the factory fender flares and inner liners have been completely removed. Ensure the new flares are correctly oriented (front/rear, driver/passenger side) and aligned with the vehicle's mounting points.
- Turn Signal Lights Not Working:
- Verify that all electrical connections are secure and properly wired to the vehicle's turn signal circuit.
- Check for blown fuses in the vehicle's fuse box related to the turn signals.
- Ensure the vehicle's battery is reconnected and fully charged.
- Àwọn Ìfọ́nká Tí Kò Lẹ́sẹ̀: Re-tighten all mounting hardware. If issues persist, inspect the mounting points on the vehicle and the flares for any damage or deformation.
8. Atilẹyin ọja ati Support
The Hooke Road Flux Tube Fender Flares Kit is backed by a 2-odun olupese atilẹyin ọja lati ọjọ ti o ra. Atilẹyin ọja yi ni wiwa awọn abawọn ninu awọn ohun elo ati iṣẹ ṣiṣe labẹ lilo deede.
For warranty claims, technical assistance, or any product-related inquiries, please contact Hooke Road customer support. Lifetime customer support is provided to ensure your satisfaction.
Fun iranlọwọ siwaju sii, jọwọ ṣabẹwo si Ile itaja Hooke Road.
