1. Ifihan
The WUBEN PL01 is a compact, high-performance pen light designed for various applications including home use, outdoor activities, emergencies, and inspections. It features a bright 650-lumen output, dual power options (rechargeable battery or AAA batteries), IP68 waterproof rating, and a durable aluminum alloy construction. This manual provides detailed instructions for its safe and effective use.
Image 1.1: The WUBEN PL01 Pen Light, showcasing awọn oniwe-aso oniru ati iwapọ iwọn.
2. Ohun ti o wa ninu Apoti
Jọwọ rii daju pe gbogbo awọn ohun kan wa nigbati o ba ṣii package naa:
- WUBEN PL01 Pen Light x 1
- Rechargeable Battery (pre-installed or separate) x 1
- Okun gbigba agbara Iru-C x 1
- Lanyard x 1
- Spare O-rings x 2
- Ilana olumulo (iwe yii) x 1
Image 2.1: Contents of the WUBEN PL01 package, including the pen light, charging cable, lanyard, and spare O-rings.
3. Eto
3.1 Fifi sori batiri
The WUBEN PL01 supports two power sources: the included rechargeable battery or two standard AAA batteries (not included). Ensure correct polarity during installation.
- Yọ fila iru ti filaṣi.
- Insert the rechargeable battery or two AAA batteries with the positive (+) end facing towards the head of the flashlight.
- Securely re-screw the tail cap until it is fully tightened.
Image 3.1: Illustration of the dual power options for the WUBEN PL01, showing both the rechargeable battery and AAA battery configuration.
3.2 Ngba agbara si Batiri gbigba agbara
The included rechargeable battery features a built-in USB-C charging port. The flashlight itself does not have an integrated charging port.
- Unscrew the tail cap and remove the rechargeable battery from the flashlight.
- Connect the provided USB-C charging cable directly to the charging port on the battery.
- So opin keji okun USB-C pọ mọ orisun agbara USB ti o baamu (fun apẹẹrẹ, adapter odi, ibudo USB kọmputa).
- A red indicator light on the battery signifies that it is charging.
- Ina Atọka yoo tan alawọ ewe nigbati batiri ba ti gba agbara ni kikun.
- Charging typically takes approximately 1.5 hours.
- Once charged, reinsert the battery into the flashlight and secure the tail cap.
4. Awọn ilana Iṣiṣẹ
4.1 Agbara Tan / Pa
To turn the WUBEN PL01 on or off, perform a full press of the tail switch button.
4.2 Ipo Yipada
With the light turned on, half-press the tail switch button to cycle through the available brightness modes in the following sequence:
- Oṣupa: 1 Lumen
- Kekere: 50 Lumens
- Alabọde: 150 Lumens
- Ga: 650 Lumens
The flashlight features a mode memory function, meaning it will activate in the last used brightness mode when turned on again.
Image 4.1: Diagram illustrating the tail switch operation for power on/off and mode cycling.
Aworan 4.2: Examples of the WUBEN PL01's four brightness modes in various practical scenarios, from facial examination to night walking.
4.3 Dual-Direction Clip Usage
The WUBEN PL01 is equipped with a versatile two-way clip, allowing for secure attachment to various items for hands-free lighting.
- Pocket Carry: Attach the clip to a shirt pocket or pants pocket for easy access.
- Backpack Strap: Secure the flashlight to a backpack strap for illumination during hikes or walks.
- Cap Mount: Clip the flashlight to the brim of a cap to convert it into a temporary headlamp.
Image 4.3: Demonstrates the versatility of the dual-direction clip, showing the flashlight attached to a pocket, backpack strap, and cap.
5. Itọju
5.1 Ninu
Lati ṣetọju iṣẹ ti o dara julọ ati irisi:
- Nu ara filaṣi mọ pẹlu asọ, damp asọ. Yago fun awọn kẹmika lile tabi awọn ohun elo abrasive.
- For the lens, use a clean, soft cloth specifically designed for optical surfaces.
5.2 O-ring Replacement
The PL01's IP68 waterproof rating relies on properly sealed O-rings. Periodically inspect them for any signs of wear, cracks, or damage.
- If O-rings appear damaged, replace them with the provided spare O-rings.
- Apply a thin layer of silicone grease to the O-rings to ensure a better seal and prevent drying.
5.3 batiri Itọju
- If the flashlight will not be used for an extended period, remove the batteries to prevent potential leakage and damage.
- For the rechargeable battery, recharge it every 3-6 months to maintain its overall lifespan and capacity.
Image 5.1: The WUBEN PL01's Type III hard-anodized aluminum body, highlighting its scratch, rust, and impact resistance.
Image 5.2: The WUBEN PL01 demonstrating its IP68 waterproof and 2-meter impact resistance, suitable for demanding environments.
6. Laasigbotitusita
If you encounter issues with your WUBEN PL01, please refer to the following common problems and solutions:
- Imọlẹ ko tan:
- Ensure the batteries are installed with correct polarity.
- Check if the rechargeable battery is charged, or if AAA batteries are new.
- Verify that the tail cap is fully tightened. A loose tail cap can prevent electrical contact.
- Clean the battery contacts and the contact points inside the flashlight with a clean cloth.
- Ina tan tabi di didin lairotẹlẹ:
- The battery level may be low. Recharge the included battery or replace AAA batteries.
- Ensure the tail cap is securely tightened.
- Clean battery contacts and internal contact points.
- Water ingress (if exposed to water):
- Immediately turn off the flashlight and remove the batteries.
- Inspect the O-rings for any damage, tears, or improper seating. Replace if necessary.
- Ensure the tail cap was fully tightened before exposure to water.
- Allow the flashlight to dry completely before reassembling and attempting to use it.
If the problem persists after attempting these solutions, please contact WUBEN customer support.
7. Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Awoṣe | PL01 |
| Awọn ọna Ijade | High (650 Lumens), Medium (150 Lumens), Low (50 Lumens), Moon (1 Lumen) |
| Akoko ṣiṣe | High: 1 hour, Medium: 2.5 hours, Low: 7 hours, Moon: 125 hours |
| Batiri Iru | Rechargeable (Included) / 2 x AAA Battery (Not Included) |
| Ijinna tan ina | 110 Mita |
| Tente Beam kikankikan | 3000 CD |
| LED | 1 x 315D |
| Mabomire Rating | IP68 (Submersible in 2m water for 1 hour) |
| Atako Ipa | 2 Mita |
| Iwọn | 1.59 iwon (pẹlu batiri) |
| Awọn iwọn (L x D) | 5.31 inches x 0.59 inches |
| Ohun elo | Aluminiomu anodized |
| Iwọn otutu awọ | 5000 Kelvin |
Image 7.1: Diagram illustrating the internal components of the WUBEN PL01, focusing on the 315D LED emitter and optical system.
8. atilẹyin ọja Information
WUBEN products typically come with a manufacturer's warranty. For specific warranty terms, conditions, and registration details, please refer to the official WUBEN webojú òpó wẹ́ẹ̀bù tàbí kí o kàn sí àwọn oníbàárà wọn. Pa ìwé ẹ̀rí ìrajà rẹ mọ́ gẹ́gẹ́ bí ẹ̀rí ìrajà fún èyíkéyìí ẹ̀tọ́ àtìlẹ́yìn.
9. Onibara Support
For further assistance, product inquiries, or technical support, please visit the official WUBEN website or contact their customer service department. You can often find FAQs, troubleshooting guides, and contact information on their webojula.
Official WUBEN Store: WUBEN Store on Amazon
