TELECO TVMIO868A02 Remote Control User Manual

Ọja Pariview

The TELECO TVMIO868A02 is a 2-channel remote control designed for operating up to two automated systems such as gates, garage doors, rolling shutters, or lighting. It operates on the 868.3 MHz frequency and utilizes rolling code technology for secure transmission, preventing unauthorized copying or interference. This compact and robust remote control is suitable for both residential and collective use.

Aworan: Iwaju view of the TELECO TVMIO868A02 remote control, showing its two buttons and sleek design.

Package Awọn akoonu

• 1 x TELECO TVMIO868A02 Remote Control
• 1 x CR2032 Lithium Battery (pre-installed)
• 1 x Programming Instruction Manual (French)
• 1 x DOMOBIP Keychain (with integrated shopping cart token)

Image: The DOMOBIP keychain, included with the remote control, featuring a shopping cart token.

Eto ati siseto

The TELECO TVMIO868A02 remote control comes with a pre-installed CR2032 battery. Programming can be done via the receiver or by duplication from an existing remote control.

Programming via Receiver

1. Locate the "PROG" or "P1" button on your receiver unit.
2. Press and hold the "PROG" or "P1" button on the receiver.
3. While the receiver is in programming mode, press the desired button on your new TELECO TVMIO868A02 remote control.
4. Release the button on the remote control, then release the button on the receiver. The remote should now be programmed.

Programming by Duplication

This method requires an existing, already programmed TELECO remote control.

1. On the back of the already programmed remote control, locate the "P3" button.
2. Press and hold the "P3" button on the existing remote control.
3. While holding "P3", press the button on the existing remote that you wish to duplicate.
4. Immediately after, press the corresponding button on the new TELECO TVMIO868A02 remote control.
5. Release both buttons. The code should now be transferred to the new remote.

Aworan: Ẹyin view of the remote control, displaying the model number TVMIO868A02 and indicating the location of the P3 button for duplication programming.

Collective Residence Mode

In some collective residences (e.g., apartment buildings), the addition of new remote controls may be restricted. In such cases, only the building manager or syndicate administrator can authorize and register new transmitters with the receiver system.

Awọn ilana Iṣiṣẹ

Once programmed, each of the two buttons on the TELECO TVMIO868A02 remote control can operate a distinct automated system. Simply press the corresponding button to activate the desired function (e.g., open/close gate, activate lighting).

• Ibiti: The remote control offers a range of up to 150 meters in open field conditions. In urban environments, the effective range is typically between 50 and 80 meters, depending on obstacles and interference.
• Aabo: The rolling code technology ensures that each transmission is unique, providing enhanced security against signal cloning or unauthorized access.

Aworan: Iwaju view of the remote control, highlighting the two distinct buttons for operating different systems.

Itoju

Batiri Rirọpo

The remote control is powered by a single CR2032 (3V) lithium battery. When the remote's range decreases or it stops responding, it may be time to replace the battery.

1. Ṣí iṣakoso latọna jijin pẹlu iṣọra casing. Refer to the physical instruction manual for specific opening procedures if needed.
2. Yọ batiri CR2032 atijọ kuro.
3. Insert a new CR2032 (3V) lithium battery, ensuring correct polarity.
4. Ti iṣakoso latọna jijin de casing ni aabo.

Itoju ati Ibi ipamọ

The remote control has an IP20 protection rating, meaning it is protected against solid objects larger than 12.5mm but has no special protection against water. It is recommended for indoor use or sheltered outdoor environments. Avoid exposing the remote to direct moisture, extreme temperatures, or strong impacts.

Laasigbotitusita

• Latọna jijin ko dahun:
  • Ṣayẹwo boya batiri naa nilo aropo.
  • Ensure the remote is properly programmed to the receiver. Re-attempt programming if necessary.
  • Rí i dájú pé a ti tan olugba naa ati pe o n ṣiṣẹ daradara.
• Iwọn to lopin:
  • Rọpo batiri naa.
  • Ensure there are no significant obstructions (e.g., thick walls, metal structures) between the remote and the receiver.
  • Yẹra fún àwọn orísun ìdènà rédíò tó lágbára.
• Awọn oran aibaramu:
  • This remote control is specifically designed for TELECO MIO/TVMIO systems operating at 868.3 MHz. It is ko ni ibamu with TELECO 433 MHz versions or systems from other brands (e.g., Nice, Somfy, BFT, FAAC).
  • Always verify the frequency (868 MHz) and the exact model reference of your original remote control or receiver before purchase.
• Programming issues in collective residences:
  • If you are in a collective residence, programming new remotes might be centrally controlled. Contact your building manager or syndicate administrator for assistance.

Awọn pato

Aworan: Ẹgbẹ profile of the remote control, illustrating its slim design.

Ibamu

The TELECO TVMIO868A02 remote control is compatible with the TELECO MIO / TVMIO range operating at 868 MHz.

Awọn awoṣe ibaramu:

• RCD-868-A04N
• TVRCM868A02
• RCD-868-M04
• TV-LINK and associated models operating at 868.3 MHz

Replaced Models:

• TXP-868-A02
• TVTXP-868-A01 / A02
• I-LIKE and other equivalent references at 868 MHz

Important Incompatibility Notes:

• Yi latọna jijin ni ko ni ibamu with TELECO 433 MHz versions or models with a different appearance.
• O ṣe ko ṣiṣẹ with systems from other manufacturers such as Nice, Somfy, BFT, FAAC, etc.

Aworan: Angled view ti iṣakoso latọna jijin, ifihanasing apẹrẹ ergonomic rẹ.

Awọn ero pataki

• Always verify the frequency (868 MHz) and the physical appearance of your original remote control to ensure compatibility.
• The exact model reference is often indicated on the back or inside the remote (under the battery).
• If you have any doubts about compatibility, contact customer service with a photo of your current model.
• For collective residences, ensure you have authorization or that the receiver accepts new transmitters before attempting to program.