Ọrọ Iṣaaju
This manual provides detailed instructions for the safe and effective use of your WUBEN E7 and WUBEN L3 Rechargeable Flashlight Bundle. Please read this manual thoroughly before operating the flashlights and retain it for future reference.
Image: The WUBEN E7 mini flashlight and the WUBEN L3 tactical flashlight shown together.
Ṣeto
WUBEN L3 Battery Installation & Initial Charge
- Yọ Idabobo Batiri kuro: Unscrew the tail cap of the WUBEN L3 flashlight. Locate and remove the blue insulation sheet covering the battery. This sheet prevents battery discharge during shipping.
- Reinsert Battery: Ensure the battery is inserted with the positive (+) end facing towards the head of the flashlight.
- Secure Tail Cap: Screw the tail cap back on tightly. The flashlight features a weather-sealing O-ring to ensure water resistance when properly closed.
- Gbigba agbara akọkọ: Twist the ring near the head of the L3 flashlight to reveal the USB-C charging port. Connect the provided Type-C charging cable to the port and a compatible USB power source. The indicator light will be red during charging and turn blue when fully charged. Charging from empty to full takes approximately 100-160 minutes depending on the charger (e.g., 9V/2A: ~100 mins, 5V/2A: ~160 mins).
Image: The WUBEN L3 flashlight being charged via its USB-C port, illustrating its fast-charging feature.
WUBEN E7 Initial Charge
The WUBEN E7 also features a USB-C charging port. Connect it to a compatible USB power source using the provided cable. Refer to the indicator light for charging status (red for charging, blue for fully charged).
Attaching Accessories (WUBEN L3)
- Agekuru igbanu: The L3 flashlight comes with a removable belt clip for convenient carrying. It can be attached or removed by sliding it along the body of the flashlight.
- Lanyard: A lanyard is included for added security and ease of access. Attach it to the designated loop on the tail cap.
Awọn ilana Iṣiṣẹ
WUBEN L3 Flashlight Operation
The WUBEN L3 is controlled by a single tail switch button.
- Ni akoko kukuru: Tap the tail switch button for momentary illumination. The light will turn off when the button is released.
- Títàn/Pípa nígbà gbogbo: Fully press and click the tail switch button to turn the flashlight on or off.
- Mode Switching (Low, Medium, High): When the flashlight is on, lightly tap the tail switch (without clicking) to cycle through the brightness modes: Moon (5 lumens) → Kekere (150 lumens) → Alabọde (500 lumens) → O ga (1500 lumens). The flashlight will remember the last used mode when turned off and on again.
- Turbo Mode (3000 lumens): From any mode, press and hold the tail switch for approximately 0.5 seconds to activate Ipo Turbo (3000 lumens). Release the button to return to the previously used mode. Note: The L3 will automatically step down from 1500 lumens (High mode) to 1100 lumens after 4 minutes to prevent overheating.
- Ipo Strobe: Double-click the tail switch to activate Ipo Strobe.
- Ipo SOS: Triple-click the tail switch to activate Ipo SOS.
WUBEN E7 Flashlight Operation
The WUBEN E7 offers 6 lighting modes and a memory function.
- Ipo Yipada: Click the switch and long press to trigger gear selection (specific details on button interaction for E7 are not fully provided in the source, but generally implies cycling through modes).
- Super Bright Mode: Double-click the switch to activate Super Bright mode (1800 lumens).
- Burst Flash Mode: Triple-click the switch to activate Burst Flash mode (Strobe).
- Iṣẹ titiipa: Four consecutive clicks will lock the flashlight to prevent accidental activation.
- Iṣẹ Iranti: The E7 will remember the last used brightness mode when turned off and on.
Image: Key features of the WUBEN E7, including maximum output, beam distance, runtime, drop resistance, waterproofing, and floodlight angle.
Power Bank Function (WUBEN L3)
The WUBEN L3 can function as a power bank to charge other devices.
- Mu Bank agbara ṣiṣẹ: Twist the ring near the head of the L3 flashlight to reveal the USB-C port. Connect your device (e.g., smartphone) to the L3 using a compatible USB-C cable.
- Abajade: The L3 provides up to 18W output for charging. Note that actual output may vary depending on the connected device and cable.
Image: The WUBEN L3 flashlight connected to a smartphone, demonstrating its capability to act as a backup power source.
Itoju
- Ninu: Máa fọ ara fìlànà pẹ̀lú ìrọ̀rùn, d déédéé.amp cloth. Keep the lens free of dust and debris for optimal light output.
- Itọju O-Oruka: The L3 flashlight uses O-rings for waterproofing. Periodically inspect the O-rings for wear and tear. Lubricate them with silicone grease if necessary to maintain the IP68 rating. Replacement O-rings are included in the package.
- Itọju Batiri: Store the flashlights in a cool, dry place. If storing for extended periods, charge the batteries to approximately 50% capacity to prolong their lifespan. Avoid fully discharging the batteries.
- Idaabobo omi: Both E7 and L3 models are IP68 rated, meaning they are protected against dust ingress and can withstand immersion in water up to 2 meters for 1 hour. Ensure all caps and ports are securely closed before exposing the flashlights to water.
Image: WUBEN E7 flashlights showcasing their magnetic base and IP68 waterproof design in a rainy environment.
Laasigbotitusita
- Ina filaṣi Ko Tii:
- Ensure the battery insulation sheet has been removed (for L3).
- Ṣàyẹ̀wò bóyá a fi batiri náà sí i dáadáa pẹ̀lú polarity tó tọ́.
- Verify the battery is charged. Refer to the power indicator.
- For E7, check if the lock function is activated (four clicks to unlock).
- Flashlight Overheating (L3): The L3 is designed to automatically reduce brightness from 1500 lumens (High mode) to 1100 lumens after 4 minutes to manage heat. This is a normal safety feature. If the flashlight becomes excessively hot to touch, turn it off and allow it to cool down.
- Awọn ọran gbigba agbara:
- Ensure the USB-C cable is securely connected to both the flashlight and the power source.
- Gbiyanju okun USB-C ti o yatọ tabi ohun ti nmu badọgba agbara.
- Verify the charging port is clean and free of debris.
- Power Bank Function Not Working (L3): Ensure the L3 battery has sufficient charge. Some devices may require specific charging protocols not fully supported by the L3's 5V output.
Awọn pato
Ina filaṣi kekere WUBEN E7
- Ijade ti o pọju: 1800 Lumens
- LED: P9 High Color Rendering 6500K LED
- Floodlight Angle: 175° Ultra-wide
- Awọn ọna: High/Med/Low/Super Bright/Strobe/SOS (6 modes with memory function)
- Idiwon ti ko ni omi: IP68
Image: Comparison of light output and color temperature from the WUBEN E7, showing Cool White 6500K and Medium White 5000K.
WUBEN L3 Tactical Flashlight
- Ijade ti o pọju: 3000 Lumens
- Ijinna Beam ti o pọju: 226 mita
- Batiri: 4800mAh Rechargeable Li-ion (21700, 3.7V, 17.76Wh)
- Gbigba agbara: Dual-way USB-C (Max 18W input/output)
- Awọn ọna: Turbo/High/Med/Low/Moon/Strobe/SOS (7 modes with mode memory)
- Idiwon ti ko ni omi: IP68
- Ohun elo: III MIL-Spec Anodized Finish
Image: The WUBEN L3 flashlight demonstrating its ultra-bright output of 3000 lumens over a significant distance in an outdoor setting.
Atilẹyin ọja ati Support
For warranty information, technical support, or any inquiries regarding your WUBEN E7 & L3 Flashlight Bundle, please refer to the official WUBEN website or contact WUBEN customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.
You can visit the official WUBEN store for more information: WUBEN Store
