AUTOMATE Iṣakoso4 Pulse Pro Ipele
Automate PULSE PRO LORIVIEW
Ṣe alekun iriri Aifọwọyi rẹ nipa iṣakojọpọ lainidi awọn ojiji alupupu adaṣe pẹlu awọn eto Ile Smart CONTROL4. Ipele Pulse Pulse Automate nfunni ni isọpọ ti o lagbara pẹlu iṣakoso iboji ọtọtọ ati ibaraẹnisọrọ ọna meji, pese awọn imudojuiwọn akoko gidi lori ipo iboji ati awọn ipele batiri. Ifihan mejeeji Ethernet (CAT 5) ati Asopọmọra alailowaya 2.4GHz, Pulse PRO Hub ṣe idaniloju isọpọ adaṣe ile ti o rọrun nipasẹ ibudo RJ45 rọrun-si-wiwọle ti o wa ni ẹhin ibudo naa. Ibudo kọọkan ṣe atilẹyin fun awọn ojiji 30, ti o jẹ ki o jẹ ojutu to wapọ fun eyikeyi iṣeto adaṣe ile.
LORIVIEW:
| Control4 Version Required | 2.9.0 o kere ju |
| Olùgbéejáde | afikun4 |
| Ọjọ Itusilẹ akọkọ | 5/28/2019 |
| Ọjọ Atunse kẹhin | 1/24/2025 |
| Imeeli atilẹyin | ustechsupport@rolleaseacmeda.com |
Akiyesi: For support of real time updates the annex4 Link driver is required. You can find the driver at: https://annex4.link/drivers/link
HARDWARE fifi sori
- Install all shades/blinds/motors at desired locations
- Connect the Hub to the Automate Pulse app
- Connect all shades/blinds/motors to the Automate Pulse app
ÌRÁNTÍ wakọ
- Place the “Automate Pulse PRO Hub” driver into the project.
- Navigate to the Connections section and select the Network tab.
- Tẹ adiresi IP sii ti Pulse PRO Hub laifọwọyi.
- Confirm that shades have been detected by looking at the Detected Drivers property.
- For each shade that the “Automate Pulse Hub” has added to the connections add an “Automate Pulse Shade” driver to the project.
- Bind the “Automate Pulse Shade” drivers to the “Automate Pulse Hub”.
- a) Once the connection has been bound the driver will automatically populate shade properties.
- Set the ‘Shade Movement Type’ to ‘Move’ or ‘Rotate’ to determine what the driver should control.
- a) ‘Move’ will control basic shade movement.
- b) ‘Rotate’ will control the motor rotation.
- Run the ‘Calibrate’ action on the shade, this will prepare the driver to calculate the travel times of the shades. By doing this the driver will accurately display ramp awọn oṣuwọn fun kan ti o dara olumulo iriri.
- Sọ awọn Atukọ.
AKIYESI: Grayed out sections are part of the hub driver installation.
Iwakọ yii jẹ Alakoso Atọka Atọka fun Rollease Acmeda Automate Pulse PRO Hub. O gba iṣakoso IP laaye lori awọn ojiji Rollease lati CONTROL4.
DRIVE FOR THE MOTOR
Awọn ẹya ti o ni atilẹyin:
- Drag and drop installation
- Easy calibration of shade travel time
- Control of motor rotation and shade movement
Awọn ohun-ini:
Awọn isẹ:
Asopọmọra:
FOR THE HUB
Awọn ẹya ti o ni atilẹyin:
- Simple installation of the hub driver by connecting the network connection;
- Automatically calculates the travel time of the motors accurate to within 50ms;
Awọn ohun-ini:
Awọn isẹ:
Asopọmọra:
COMMOMS MISTAKES:
- Titẹsi adiresi IP ti ko tọ si ni laini iṣeto ni "Adirẹsi IP".
- Ti o ba kuna lati ṣawari awọn ẹrọ lẹẹmeji ṣayẹwo eyi!
CONTROL4 SYSTEM CONNECTION:
IBEERE TI A MAA BERE LOGBA
Q. Ko si Pulse PRO Ipele ti a rii.
A. Rii daju pe Automate Pulse PRO rẹ ti sopọ si nẹtiwọki ti o tọ ati ki o gba Adirẹsi IP kan ti o wa ati ki o tun ni ibaraẹnisọrọ pẹlu nẹtiwọki nipa lilo Automate Shades App.
Q. Awọn ifilelẹ iboji ko ṣeto daradara.
A. Calibrate shade limits with your Rollease Acmeda remote before setting the appropriate open and close time within CONTROL4 SYSTEM.
Q. Iboji ko ni gbigbe rara.
A. Make sure the selected Pulse PRO Hub is the correct Pulse PRO Hub for the shade to be controlled. Confirm the correct bindings are set in the CONTROL4 System connections tab between the Pulse PRO Hub and Shade drivers.
Q. I have multiple Pulse PRO Hubs, what do I do?
A. Load two Automate Pulse PRO Hub drivers. After selecting “Retrieve Hubs” located in the driver actions tab, you will see different Automate Pulse PRO Hubs - select the desired one.
Q. I don’t see any shade bindings in the Pulse PRO Hub driver?
A. Yan "Gba awọn iboji pada" ti o wa ninu taabu awọn iṣẹ awakọ.
Q. How do I scan for available Automate Pulse PRO Hubs?
A. Once the Automate Pulse PRO Hub is properly connected via the Ethernet cable or Wireless network, navigate to the Automate Pulse Hub Properties page within Composer. Select “Retrieve Hubs” located in the driver actions tab.
Awọn orisun atilẹyin:
Fun iranlọwọ siwaju sii, kan si alagbata rẹ, ṣabẹwo si wa webojula ni www.rolleaseacmeda.com.
rolleaseacmeda.com
0 2025 Rollease Acmeda Ẹgbẹ
Awọn iwe aṣẹ / Awọn orisun
 |
AUTOMATE Iṣakoso4 Pulse Pro Ipele [pdf] Itọsọna olumulo Control4 Pulse Pro Hub, Pulse Pro Hub, Ipele |