Olutọju iwọn otutu ti ọpọlọ E62 PID
Pariview & Irisi
Awọn bọtini ati awọn ifihan
IṢẸ KEYPAD
KỌKỌRIN YI: 
Bọtini yii ni a lo lati yan paramita lati jẹ viewed tabi ṣatunṣe.
KỌKỌRỌ SOKE/Ilọsi:
Yi bọtini ti wa ni lo lati mu awọn iye ti awọn ti o yan paramita.
KỌKỌRỌ IWAJU/Dinku: 
Bọtini yii ni a lo lati dinku iye paramita ti o yan.
KOKO SHIFT:
A lo bọtini yii lati:
- Move to the digit of the selected parameter and change the value by using up or down key to increase or decrease the value.
Yi lọ Soke: 
Awọn bọtini meji ti a tẹ ni iṣọkan ni a lo lati:
- Go to the previous parameter
Tun: + 
Awọn bọtini meji ti a tẹ ni iṣọkan ni a lo lati:
- Yi ifihan pada si iboju ile.
- Tun itaniji dimu to ni kete ti o ti yọ ipo itaniji kuro.
- Duro ipo iṣakoso afọwọṣe, Iyipada-iyipada aifọwọyi tabi ipo isọdiwọn.
- Ko ohun-Tuning laifọwọyi tabi ifiranṣẹ aṣiṣe ibaraẹnisọrọ kuro.
- Enter the manual control menu if a failure mode occurs.
Yi lọ si isalẹ: 
Two keys pressed synchronously directly go to the Manual control mode
Tẹ bọtini:
Tẹ ki o si mu fun iṣẹju-aaya 5 tabi ju bẹẹ lọ si:
- Enter the Auto-Tuning mode.
Ifihan yoo han. - Enter the manual control mode.
Ifihan yoo han.
Enter the setup menu mode.
Ifihan yoo han. 
Perform calibration of a selected parameter during the calibration procedure. The display will show
Akojọ aṣayan ti pin si awọn ẹgbẹ marun. Wọn jẹ bi wọnyi:
- Olumulo Akojọ
- Auto-Tuning Mode Menu
- Afowoyi Ipo Akojọ aṣyn
- Akojọ Akojọ aṣyn
- Calibration Mode Menu
- Tẹ for the next parameter ; Press ati bọtini lati pada si paramita ti tẹlẹ.
- Tẹ mọlẹ for 3.1 seconds, then let go to select auto tuning mode.
- Tẹ mọlẹ for 4.2 seconds, then let go, to select manual control mode.
- Tẹ mọlẹ for 5.3 seconds, then let go to select setup mode.
- Tẹ mọlẹ fun awọn aaya 6.4, lẹhinna jẹ ki lọ lati yan ipo isọdiwọn.
Olumulo Akojọ
Lo key to enter basic menu parameters, and press again to select SP1, SEL1~SEL8.
Tẹ lati pada si išaaju.
Auto-Tuning Mode
Tẹ key 5 seconds to activate Auto-Tuning Mode
Afowoyi Ipo Akojọ aṣyn
Tẹ key 3 seconds to execute the selected default program
Enter Manual Control Mode; refer to Manual 6.1 & 6.8.2~6.8.4
Akojọ Akojọ aṣyn
The setup menu has been categorized into eight categories.
They are listed as below.
- Akojọ aṣayan ipilẹ (bASE)
- Akojọ aṣyn jade (oUT)
- Communication Menu (CoMM)
- User Select Menu (SEL)
Akojọ aṣayan ipilẹ (bASE)
Lo or key to get bASE in the lower display then use key to enter to basic menu parameters.
Akojọ aṣyn jade (oUT)
Lo or key to get oUT in the lower display then use key to enter to output menu parameters.
Communication Menu (CoMM)
Lo or key to get CoMM in the lower display then use key to enter to communication menu parameters.
Please note that confirm A2FN set to CoMM when using communication.
User Select Menu (SEL)
Lo or key get SEL in the lower display then use key to enter to select the user menu parameters.
Ipo odiwọn
Tẹ key for 2 seconds or longer (not more than 3 seconds) ; then release it to enter calibration Mode.
Tẹ key for 5 seconds to perform calibration
- Please note that it is required to use specialized equipment to apply calibration, attempting to change will affect device accuracy
Akiyesi:
- Using Manual, Auto-Tuning, Calibration modes will break the control loop and change some of the previous setting data. Make sure that the system is allowable to apply these modes.
- The flow chart shows a complete list of all parameters. For actual application, the number of available parameters will vary depending on the setup and model of the controller and will be less than that shown in the flow chart.
- The user can select up to 8 parameters to put in the user select menu by using the SEL1~SEL8 parameters in the setup menu
Ṣaaju ki o to Bẹrẹ, Ṣeto Input/Ojade
Lẹhin ti agbara soke, tẹ mọlẹ for 5.3 seconds, then let go to enter Setup Menu. Complete Parameter setting, INPT, UNIT, DP, O1TY, O1L and O1H.
- Enter the Setup Menu. Press for 5 seconds to enter Basic Menu (bASE). Finish setting for INPT, UNIT and DP. Exit the level.
- Return to the Setup Menu. Press for 5 seconds to enter Output Menu (oUT). Finish setting for O1TY, O1L and O1H. Press and hold ati pada si oju-ile.
OP1L / OP1H Table
| Ibiti o | OP1L | OP1H | |
| OM9A-3 | 4-20 | 20.0 | 100.0 |
| OM9A-3 | 0-20 | 0.0 | 100.0 |
| OM9A-5 | 0-5V | 0.0 | 50.0 |
| OM9A-5 | 1-5V | 10.0 | 50.0 |
| OM9A-5 | 0-10 | 0.0 | 100.0 |
* When O1TY as DC.MA or DC. Vo, set the value based on usage requirement
Asopọ ebute
Parimeter akiyesi
User Menu Parameter
| Modbus | Paramita | Apejuwe | Ibiti o | Aiyipada | Wiwọle | |
| 0 | SP1 | Ṣeto Ojuami 1 | Kekere: SP1L
Iwọn giga: SP1H |
25.0 °C | R/W | |
| 64 | PV | Iye ilana | Kekere: -19999
ti o ga: 45536 |
(77.0°F) | R | |
| 65 | SV | Lọwọlọwọ ṣeto ojuami iye | Kekere: SP1L
Iwọn giga: SP1H |
—— | R | |
| 44 |
SEL1 |
Yan paramita 1st fun akojọ aṣayan olumulo | 0 KOSI
1 A1SP 2 A2SP 3 TItiipa 4 INPT 5 PB 6 TI |
7 TD
8 SHIF 9 OFST 10 O1HY 11 A1HY 12 A2HY 13 ADDR |
—— | R/W |
| 45 | SEL2 | Select 2nd parameter | Select 2nd parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 46 | SEL3 | Select 3rd parameter | Select 3rd parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 47 | SEL4 | Select 4th parameter | Select 4th parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 48 | SEL5 | Select 5th parameter | Select 5th parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 49 | SEL6 | Select 6th parameter | Select 6th parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 50 | SEL7 | Select 7th parameter | Select 7th parameter for user manual. Same as the SEL1 | 0 | R/W | |
| 51 | SEL8 | Select 8th parameter | Select 8th parameter for user manual. Same as the SEL1 | 0 | R/W | |
Manual Mode Parameter
| Modbus | Paramita | Apejuwe | Ibiti o | Aiyipada | Wiwọle |
| 66 | MV1 | Ijade 1% Iye | Kekere: 0.00
ga: 100.00% |
—– | R (R/W,
Afọwọṣe) |
Basic (bASE) Parameter
| Modbus | Paramita | Apejuwe | Ibiti o | Aiyipada | Wiwọle |
| 3 | Titiipa | Yan paramita lati wa ni titiipa | 0 Kò: Ko si paramita ti wa ni titiipa
1 SEt: Setup data are locked 2 uSEr: Setup data and user data are locked. SetPoint are unlocked. 3 ALL: All data are locked |
0 | R/W |
| 4 | INPT | Input sensor selec- tion | 0 J_tC: J iru Thermocouple
1 K_tC: K iru Thermocouple 2 t_tC: T type Thermocouple 3 R_tC: R iru Thermocouple 4 S_tC: S type Thermocouple 5 Pt. dN: PT 100 DIN 6 Pt.JS: PT 100 JIS |
1 | R/W |
| 5 | UNIT | Aṣayan titẹ sii | 0 oC: °C unit
1 oF: °F unit |
0 | R/W |
| 6 | DP | Decimal point selec- tion | 0 No.dP: no decimal point
1 1-dP: 1 aaye eleemewa |
1 |
R/W |
|
9 |
SP1L |
Low iye to ṣeto ojuami iye | Kekere:
J_TC: -120.0°C (-184.0°F) K_TC: -200.0°C (-328.0°F) T_TC: -250.0°C (-418.0°F) R_TC: 0.0°C ( 32.0°F) S_TC: 0.0°C ( 32.0°F) PTDN: -200.0°C (-328.0°F) PTJS: -200.0°C (-328.0°F) Iwọn giga: SP1H |
-17.8 °C
(0.0°F) |
R/W |
| 10 |
SP1H |
Ga iye to ti ṣeto ojuami iye | Kekere: SP1L
Ga: J_TC: 1000.0°C (1828.0°F) K_TC: 1370.0°C (2498.0°F) T_TC: 400.0°C ( 752.0°F) R_TC: 1767.7°C (3214.0°F) S_TC: 1767.7°C (3214.0°F) PTDN: 850.0°C (1562.0°F) PTJS: 600.0°C (1112.0°F) |
537.8 °C
(1000.0°F) |
R/W |
| 12 | FILT |
Àlẹmọ damping time constant of PV |
0 0: 0 iṣẹju-aaya akoko igbagbogbo
1 0.2: 0.2 iṣẹju-aaya akoko igbagbogbo 2 0.5: 0.5 iṣẹju-aaya akoko igbagbogbo 3 1: 1 iṣẹju-aaya akoko igbagbogbo 4 2: 2 iṣẹju-aaya akoko igbagbogbo 5 15: 5 iṣẹju-aaya akoko igbagbogbo 6 10: 10 iṣẹju-aaya akoko igbagbogbo 7 20: 20 iṣẹju-aaya akoko igbagbogbo 8 30: 30 iṣẹju-aaya akoko igbagbogbo 9 60: 60 iṣẹju-aaya akoko igbagbogbo |
2 | R/W |
| 14 | PB | Iwọn iye
iye |
Kekere: 0.0
Giga: 500.0°C (900.0°F) |
10.0 °C
(18.0°F) |
R/W |
| 15 | TI | Integral akoko iye | Low: 0, High: 3600 sec | 60 | R/W |
| 16 | TD | Iye akoko itọsẹ | Low: 0, High: 360.0 sec | 30.0 | R/W |
| 11 | SHIF | PV shift (offset)
iye |
Low: -200.0°C (-360.0°F) High: 200.0°C (360.0°F) | 0.0 °C
(0.0°F) |
R/W |
| 68 | CICF | CIC àlẹmọ yipada | 0 PAA
1 LORI |
0 | R |
Output (oUT) Parameter
| Modbus | Paramita | Apejuwe | Ibiti o | Aiyipada | Wiwọle |
| 17 | JADE1 | Iṣẹjade 1 | 0 REVR: Reverse (heating) control action
1 dIRt: Direct (cooling) control action |
0 | R/W |
| 21 | CYC1 | Jade 1 ọmọ akoko | Low: 0.1;
Giga: 90.0 iṣẹju-aaya. |
18.0 | R/W |
| 18 | O1TY | O wu 1 ifihan agbara iru | 0 RELY: Ijadejade yii
1SSrd: Ri to ipinle yiyi wakọ wakọ 2 DC.MA: DC current 3 DC.Vo: DC voltage |
0 | R/W |
| 7 | OP1L | OP1 laini o wu kekere iye iye | 0.0 ~ OP1H | 0.0 | R/W |
| 8 | OP1H | OP1 linear output
high limit value |
OP1L ~ 110.0% | 100.0 | R/W |
| 19 | O1FT | Ipo gbigbe ikuna 1 jade | 0~1000: 0.0 ~ 100.0 % to continue output 1
control function if the sensor fails, or select OFF (0) or ON (1) for ON-OFF control |
0.0 | R/W |
| 22 | OFST | Offset value for P
iṣakoso |
Kekere: 0
ga: 100.0% |
25.0 | R/W |
| 20 | O1HY | Output 1 ON-OFF
control hysteresis |
Kekere: 0.1
Giga: 50.0°C (90.0°F) |
0.5 °C
(0.9°F) |
R/W |
| 23 | PL1L | MV1 power value
iwọn kekere |
Kekere: 0
Iwọn giga: 50% tabi PL1H |
0 | R/W |
| 24 | PL1H | MV2 power value limit high | Kekere: PL1L
ga: 100% |
100 |
R/W |
| 25 | A1FN | Itaniji 1 iṣẹ fun itaniji 1 o wu | 0 Bẹẹkọ: Ko si iṣẹ itaniji
1 dE.HI: Itaniji giga iyapa 2 dE.Lo: Itaniji kekere iyapa 3 db.HI: Deviation band out of band alarm 4 db.Lo: Ẹgbẹ iyapa ni itaniji band 5 PV.HI: Ilana iye ga itaniji 6 PV.Lo: Ilana iye kekere itaniji |
1 |
R/W |
| Modbus | Paramita | Apejuwe | Ibiti o | Aiyipada | Wiwọle |
|
26 |
A1MD |
Alarm 1 operation mode |
0 NoRM: Iṣe itaniji deede
1 LtCH: Latching alarm action 2 HoLd: Mu iṣẹ itaniji duro 3 Lt.Ho: Latching & Mu igbese |
0 | R/W |
| 29 | A1HY | Alarm 1 Hysteresis control | Kekere: 0.1
Giga: 50.0°C (90.0°F) |
0.1 °C
(0.2°F) |
R/W |
| 34 | A1DL | Itaniji 1 idaduro | Kekere: 0; ga: 5999 iṣẹju-aaya | 0 | R/W |
| 28 | A1FT | Alarm 1 failure trans- fer mode | 0 oFF: OFF if sensor fails
1 lori: ON ti sensọ ba kuna |
1 | R/W |
| 1 | A1SP | Itaniji 1 ṣeto ojuami | A1FN=PVHI/PVLO
Kekere: SP1L Giga: SP1H |
100.0 °C
(212.0°F) |
R/W |
| 13 | A1DV | Alarm 1 deviation value | A1FN=DEHI/DELO/DBHI/DBLO
Kekere: 0.0 Giga: 500.0°C (900.0°F) |
10.0 °C
(18.0°F) |
R/W |
| 33 |
A2FN |
Itaniji 2 iṣẹ fun itaniji 2 o wu |
0 Bẹẹkọ: Ko si iṣẹ itaniji
1 dE.HI: Itaniji giga iyapa 2 dE.Lo: Itaniji kekere iyapa 3 db.HI: Deviation band out of band alarm 4 db.Lo: Ẹgbẹ iyapa ni itaniji band 5 PV.HI: Ilana iye ga itaniji 6 PV.Lo: Ilana iye kekere itaniji 7 COMM: RS485 |
2 |
R/W |
|
35 |
A2MD |
Alarm 2 operation mode |
0 NoRM: Iṣe itaniji deede
1 LtCH: Latching alarm action 2 HoLd: Mu iṣẹ itaniji duro 3 Lt.Ho: Latching & Mu igbese |
0 |
R/W |
| 36 | A2HY | Hysteresis control of alarm 2 | Kekere: 0.1°C
Giga: 50.0°C (90.0°F) |
0.1 °C
(0.2°F) |
R/W |
| 38 | A2DL | Itaniji 2 idaduro | Kekere: 0; ga: 5999 iṣẹju-aaya | 0 | R/W |
| 37 | A2FT | Alarm 2 failure forced transfer mode | 0 oFF: Alarm output OFF if sensor fails
1 oN: Alarm output ON if sensor fails |
1 | R/W |
| 2 | A2SP | Itaniji 2 ṣeto ojuami | A2FN=PVHI/PVLO
Kekere: SP1L Giga: SP1H |
100.0 °C
(212.0°F) |
R/W |
| 43 | A2DV | Alarm 2 deviation value | A2FN=DEHI/DELO/DBHI/DBLO
Kekere: 0.0 Giga: 500.0°C (900.0°F) |
10.0 °C
(18.0°F) |
R/W |
Communication (CoMM) Parameter
| Modbus | Paramita | Apejuwe | Ibiti o | Aiyipada | Wiwọle |
| 39 | ADDR | Address assignment of digital ibaraẹnisọrọ |
Kekere: 1
ti o ga: 255 |
1 | R/W |
| 40 | BAUD | Baud oṣuwọn ti oni ibaraẹnisọrọ | 0 2.4: 2.4 Kbits/s baud rate
1 4.8: 4.8 Kbits/s baud rate 2 9.6: 9.6 Kbits/s baud rate 3 14.4: 14.4 Kbits/s baud rate 4 19.2: 19.2 Kbits/s baud rate 5 28.8: 28.8 Kbits/s baud rate 6 38.4: 38.4 Kbits/s baud rate 7 57.6: 57.6 Kbits/s baud rate 8 115.2: 115.2 Kbits/s baud rate |
2 | R/W |
| 41 | DATA | Data bit count of dig- ital communication | 0bIt: 7 die-die
1bIt: 8 die-die |
1 | R/W |
| 42 | PARI | The parity bit of digi- tal communication | 0 EVEN: Even parity
1 odd: Odd parity 2 NoNE: No parity bit |
0 |
R/W |
Calibration Mode Parameter
| Modbus | Paramita | Apejuwe | Ibiti o | Aiyipada | Wiwọle |
| 52 | ADLO | mV calibration low
olùsọdipúpọ |
Kekere: -1999
ti o ga: 1999 |
—– |
R/W |
| 53 | ADHI | mV calibration high
olùsọdipúpọ |
Kekere: -1999
ti o ga: 1999 |
—– |
R/W |
| 54 | RTDL | RTD calibration low
olùsọdipúpọ |
Kekere: -1999
ti o ga: 1999 |
—– |
R/W |
| 55 | RTDH | RTD calibration high coefficient | Kekere: -1999
ti o ga: 1999 |
—– |
R/W |
| 56 | CJLO | Cold junction calibra-
tion low coefficient |
Kekere: -5.00
ti o ga: 40.00 |
—– |
R/W |
Miiran Paramita
| Modbus | Paramita | Apejuwe | Ibiti o | Aiyipada | Wiwọle |
| 57 | CJCT | Tutu Junction otutu | Kekere: -4000
ti o ga: 9000 |
—– | R |
| 58 | DATE | Ọjọ | Low: 0;
ti o ga: 65535 |
—– | R |
| 59 | SRNO | Nomba siriali | Low: 0;
ti o ga: 65535 |
—– | R |
| 63 | CJCL | Cold junction low calibration
voltage |
Kekere: 0
ti o ga: 7552 |
—– | R |
| 69 | EROR | Koodu aṣiṣe | Kekere: 0; ti o ga: 65535 | —– | R |
| 70 | MODE | Ipo isẹ & ipo itaniji | Kekere: 0
ti o ga: 65535 |
—– | R |
| 71 | PROG | Device version, firmware version | 67.XX | —– | R |
| 72 | Kaadi afinihan | Koodu aṣẹ | Kekere: 0; ti o ga: 65535 | —– | R/W |
| 73 | JOB1 | Koodu iṣẹ | Kekere: 0; ti o ga: 65535 | —– | R/W |
Koodu aṣiṣe
| Asise Koodu | Ifihan
Aami |
Apejuwe & Idi |
Atunse Iṣe |
| 10 | ER10 | Aṣiṣe ibaraẹnisọrọ: koodu iṣẹ buburu | Correct the communication software to meet the protocol
awọn ibeere |
| 11 | ER11 | Aṣiṣe ibaraẹnisọrọ: forukọsilẹ adirẹsi ni ibiti o ti le | Ma ṣe fun ọmọ-ọdọ naa ni adiresi ti o tobi ju ti iforukọsilẹ silẹ |
| 14 | ER14 | Communication error: attempt to write a
read-only data |
Maṣe kọ data kika-nikan tabi data to ni aabo si ẹrú naa |
| 15 | ER15 | Aṣiṣe ibaraẹnisọrọ: kọ iye ti ko ni ibiti o wa si iforukọsilẹ | Maṣe kọ data ti o ju iwọn lọ si iforukọsilẹ ẹrú |
| 26 | ATER | Auto-Tuning Error: Failed to perform Auto-Tuning function |
|
| 29 | EEPR | EEPROM ko le kọ bi o ti tọ | Pada si olupese fun titunṣe. |
| 30 | CJER | Biinu junction tutu fun
Thermocouple aiṣedeede |
Pada si olupese fun titunṣe. |
| 39 | SBER | Input sensor break | Replace the input sensor |
| 40 | ADER | Oluyipada A si D tabi awọn paati ti o ni ibatan | Pada si olupese atilẹba fun atunṣe. |
FAQ
Bawo ni MO ṣe wọle si Akojọ olumulo?
To access the User Menu, press the corresponding key on the controller.
Bawo ni MO ṣe mu Ipo-Tuning Aifọwọyi ṣiṣẹ?
To activate Auto-Tuning Mode, press and hold a specific key for 5 seconds.
How do I enter Manual Control Mode? To enter Manual Control Mode, press the designated key for 3 seconds. How do I perform calibration? To calibrate a parameter, press and hold the ENTER key for 5 seconds during the calibration procedure.
To enter Manual Control Mode, press the designated key for 3 seconds.
Bawo ni MO ṣe ṣe isọdiwọn?
To calibrate a parameter, press and hold the ENTER key for 5 seconds during the calibration procedure.
Awọn iwe aṣẹ / Awọn orisun
 |
Olutọju iwọn otutu ti ọpọlọ E62 PID [pdf] Ilana itọnisọna E62, QS0E620C, E62 PID Olutọju iwọn otutu, E62, Adari iwọn otutu PID, Adari iwọn otutu, Adari |