Cosmic Byte ECLIPSE TRI Mode Controller User Manual

Cosmic Byte ECLIPSE TRI Mode Controller

Awọn pato ọja

Akiyesi: All specifications are for reference and may vary depending on usage and environment.

Package Awọn akoonu

• Eclipse Controller × 1
• Replaceable D-Pad × 1
• 2.4G Receiver × 1
• USB Type-C Cable (1.5m) × 1
• Afowoyi Olumulo × 1

AGBARA

Mode Switching Position: From left to right: Bluetooth – 2.4G – NS (Xinput Bluetooth, 2.4G Receiver, Switch)

Awọn ilana Isẹ

HOME CB Indicator Light

• Blue – iOS and Android
• Orange – 2.4G Mode

Asopọ-akoko akọkọ

• 2.4G Alailowaya Ipo
  • Set the mode switch toggle to 2.4G (Middle).
  • Pulọọgi olugba USB sinu ẹrọ rẹ.
  • While the controller is powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly. Once it turns solid and the controller vibrates briefly, the connection is successful.
• Ipo Bluetooth
  • Set the mode switch toggle to Bluetooth (Left).
  • While powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly.
  • On your device (PC/Android/iOS), enable Bluetooth and select ‘Xbox Wireless Controller’.
  • When the logo light turns solid and the controller vibrates, the pairing is complete.
• Ipo Ti onirin
  • Connect the controller to your device using the included USB Type-C cable.
  • Wired mode activates automatically when connected.

Atunṣe
To reconnect to the last paired device (with the same mode), short-press the Home button.

Joystick Atunse

• Dead Zone Toggle:
  • Press and hold Left and Right Stick (LS/RS) for 5 seconds to switch between 5% and 0% deadzone.
  • Controller will vibrate to confirm the change.
• Active Zone Shape Toggle:
  • Press and hold M + LS or RS for 5 seconds to toggle between 10% square zone and 0% circle zone.

 Turbo and Continuous Fire

• Turbo Afowoyi
  • Press M + A while holding the A button to enable manual turbo (continuous fire).
  • Logo light will flash red rapidly.
• Turbo laifọwọyi
  • Press M + A again to switch to auto turbo. Press again to cancel turbo.
  • A single press of A will now fire continuously.
• Clean all Turbo
  • Press M button twice and hold M for 5 secs, controller will vibrate & clean all Turbo settings.
• Turbo Speed ​​Atunṣe
  • Hold M + Right Stick Up/Down to increase or decrease turbo speed.
  • Vibration feedback indicates change.

ABXY Lighting Adjustment

• Press M + Right Stick Left and Right to adjust brightness.
• 4 Brightness Levels: 0% → 30% → 70% → 100%

Atunse kikankikan gbigbọn

• Press and hold M + Right Stick Up to increase vibration intensity.
• Press and hold M + Right Stick Down to decrease.
• 4 Levels: 0% (off) → 30% → 70% → 100%

ABXY Ìfilélẹ Yipada

Use the layout switch on the front to toggle between XBOX-style and Alternate-style layouts.

Rapid Trigger Adjustment
Adjust LT/RT trigger travel distance using the trigger mode switch on the back for quick/short press functionality.

Isọdiwọn

• Stick & Nfa Idiwọn
  • Agbara lori oludari.
  • Dimu View + M + Menu for 3 seconds to enter calibration.
  • LED1 and LED3 will flash.
  • Rotate both sticks clockwise 3 full turns.
  • Fully press both triggers 3 times.
  • Switch triggers to short travel mode, then press them fully 3 more times.
  • Tẹ View lati jade.
  • LED1 and LED3 will stay solid for 5 seconds before powering off.
• Gyroscope odiwọn
  • Power off the controller and place it on a flat surface.
  • Dimu View + A + B + Home to enter gyro calibration.
  • LED1 and LED2 will flash.
  • After 1 second, press Menu to complete calibration. LEDs will turn off.
  • Calibration must be performed in XBOX (ABXY) layout mode.

Macro Programming (M1/M2 Buttons)

• While connected, hold M + M1 or M2 for 3 seconds to enter programming mode.
• Press the desired button to assign (e.g., A, B, etc.).
• Press M1 or M2 again to save and exit.

Akiyesi: If no button is selected, M1/M2 will be blank. Up to 21 Programmable buttons: A/B/X/Y/D-pad/LB/RB/LT/RT/L3/R3/Menu/View/Joysticks

Agbara Paa

• Hold the Home button for 5 seconds to power off.
• Auto power-off after 10 minutes of inactivity.

Atunto Adarí
Use a small pin to press the Reset hole to restore factory settings.

 Joystick Force Adjustment (Roller-Based)
The Cosmic Byte Eclipse controller features adjustable joystick tension using a built-in roller mechanism. Follow the steps below to customize the joystick force according to your preference:

• Locate the joystick roller at the base of each analog stick.
• To increase joystick resistance, rotate the roller clockwise.
• To decrease joystick resistance, rotate the roller counter-clockwise.
• Make adjustments gradually and test after each rotation to find your preferred setting.

Akiyesi: The roller mechanism allows for fine-tuning of joystick stiffness for better precision or quicker flick response in different game types (e.g., FPS vs Racing).

Ìtọ́sọ́nà Àmì Bátírì

• Batiri Kekere: Logo light flashes red once every 10 minutes
• Gbigba agbara: Logo light breathes green
• Ti gba agbara ni kikun: Logo light turns off

Mobile App Download

Download and install the “Key Linker” App from the Google Play Store or Apple App Store for advanced customization and controller adjustments.

Atilẹyin ọja

• The Eclipse Tri-Mode Controller carries a 1-year warranty against manufacturing defects only.
• Physical, water damage, and tampawọn ọja ered ko bo labẹ atilẹyin ọja.

Scan the QR Code to know the Warranty Claim Procedure.

Awọn alaye atilẹyin

• Customer Care Number: +91 7351615161 (Mon-Sat 10am to 6pm)
• WhatsApp Support: +91 7351615161
• Imeeli: cc@thecosmicbyte.com