Ìwé Ìtọ́sọ́nà Olùlò Modulu Ìbánisọ̀rọ̀ e-shock CU02

e-shock CU02 Communication Module

Ààlà

Designed for professional integration into host devices, the CU02 radio module complies with the following FCC and ISED Rules:

47 CFR FCC Part 15, Subpart C (section 15.247) RSS-247, Issue 3 (August 2023)

Awọn pato Imọ-ẹrọ

1. Ipese agbara: 8-28 Vdc
2. Awọn ẹgbẹ igbohunsafẹfẹ ṣiṣiṣẹ:
   • 2402 – 2480 MHz (Bluetooth mode)
   • 2402 – 2480 MHz (BLE mode)
   • 2412 – 2462 MHz (WiFi mode)
3. Gbigbe agbara RF:
   • 9 mW (Bluetooth mode)
   • 7 mW (BLE mode)
   • 174 mW (WiFi mode)

Awọn ipo Lilo Iṣẹ-pataki

• This radio module is for OEM integration only and cannot be sold to general public.
• The company E-Shock S.r.l. is the Grantee of this FCC ID / IC. This radio module is exclusively for integration into host devices manufactured by E-Shock S.r.l. only.

Awọn ilana Module Lopin

This modular transmitter has been tested in a “non-standalone” configuration – i.e., embedded in a test jig board – for compliance with Part 15 requirements.
The module requires the host integrator to file a Class II permissive change for each specific host, considering the test plan detailed in chapter 5.4.
A host manufacture is recommended to use FCC’s KDB 996369 D04 Module Integration Guide V01 as “best practice” for RF design engineering, testing and evaluation.

Awọn ojuse OEM lati ni ibamu pẹlu Awọn ilana FCC

1. Gbogbogbo riro
   This modular transmitter has been tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B and ICES-003 requirements, which are applicable to the final host. The final host shall be assessed for compliance with the requirements of the above Regulations, as applicable.
2. Host Manufacturer Responsibilities
   Host manufacturers are ultimately responsible for the full compliance of the host system before it can be placed on the US/Canadian market.
   This includes reassessing the transmitter module for compliance with all applicable radio and RF Exposure requirements of the FCC and ISED rules.
   Akiyesi: this radio module is designed for integration into end products manufactured by E-Shock S.r.l., which assumes full responsibility for the final compliance.
3. Multi-Radio Systems
   This module must not be incorporated into any other radio system without retesting for compliance as multi-radio and combined equipment.
   In case of any co-located radio transmitter being allowed to transmit simultaneously, or in case of portable use at closer distances from the human body than those allowing the exceptions rules to be applied, a separate additional SAR evaluation will be required, ultimately leading to a Class II Permissive Change, or more rarely to a new Grant.

Akiyesi: if these conditions cannot be met, then the FCC authorization is no longer considered valid, and the FCC ID/IC identifiers cannot be used on the final product. Then for the FCC/ISED authorization to remain valid, the final product will have to undergo additional testing to evaluate the RF exposure and a Permissive Change will have to be applied. The evaluation (SAR) is in the responsibility of the end-product’s manufacturer, as well as the Permissive Change that can be carried out with the help of a Telecommunication Certification Body.

Test plan (KDB996369 D01)
Module integrator shall confirm and demonstrate compliance with the following test plan:

• Perform Maximum Output Power test (radiated) according to Part 15.247 / KDB558074 D01 (IEEE 802.11b, frequency: 2462 MHz, ch.11; data rate: 1.0 Mbps )
• Check band edge compliance according to Part 15.247 / KDB558074 for lowest channel (IEEE 802.11b, frequency: 2412 MHz, ch.1; data rate: 1 Mbps D01)
• Check band edge compliance according to Part 15.247 / KDB558074 for upper channel (IEEE 802.11b, frequency: 2462 MHz, ch.11; data rate: 1 Mbps D01)
• Perform radiated spurious emission (frequency range 1 GHz – 25 GHz) according to Part 15.247 (IEEE 802.11b, frequency: 2437 MHz, ch.6; data rate: 1 Mbps)
  Akiyesi: radiated spurious emission test must be carried out with all transmitters active if they can operate simultaneously.
• Demonstrate compliance with human exposure requirements according to 47 CFR Part 2, § 2.1091/ KDB447498 D01 (see also chapter 7).
• Final host system requires compliance testing according to 47 CFR Part 15.

Apẹrẹ eriali

Iru eriali
The antenna must be embedded according to the following instruction:

Please refer Tvpe1DX Antenna P2ML4452-1-A.dxf (see following drawing):

Ere eriali
Antenna gain must be lower than 0.6 dBi.

Awọn ipo Ifihan RF
This modular transmitter complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated at a minimum distance of 20 cm between the radiator and the human body.
This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures (see chapter 5.3).

Ipari Ifamisi Ọja
Due to the small dimensions of this modular transmitter, FCC ID, as well as IC and HVIN identifiers, are reported in the User Manual. A removable label is also attached to the product. End product must be labeled in a visible area with the following text:

• “Contains FCC ID: 2BOUM-CU02”
• “Contains IC: 33848-CU02”

bi wulo.

Information to the End User

• The end user manual shall include all required Regulatory information/warning as follows:
• Awọn iyipada tabi awọn iyipada ti ko fọwọsi ni gbangba nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ohun elo naa.

For US market:
Ẹrọ yii ni ibamu pẹlu apakan 15 ti Awọn ofin FCC. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:

1. Ẹrọ yii le ma fa kikọlu ipalara, ati
2. Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa isẹ ti ko fẹ.

Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni nọmba Kilasi B, ni ibamu si apakan 15 ti Awọn ofin FCC. Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to tọ si kikọlu ipalara ni fifi sori ibugbe kan. Ẹrọ yii n ṣe ipilẹṣẹ, nlo ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato. Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:

• Reorient tabi tun eriali gbigba pada.
• Mu iyatọ pọ si laarin ẹrọ ati olugba.
• So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ.
• Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.

Gbólóhùn Ifihan Radiation RF
This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated at a minimum distance of 20 cm between the radiator and the human body.
This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

For Canadian market
Ẹrọ yii ni awọn atagba (awọn)/awọn olugba(awọn) ti ko ni iwe-aṣẹ ti o ni ibamu pẹlu Innovation, Imọ ati Idagbasoke Iṣowo Awọn RSS(s) laisi iwe-aṣẹ ti Canada. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:

1. Ẹrọ yii le ma fa kikọlu.
2. Ẹrọ yii gbọdọ gba kikọlu eyikeyi, pẹlu kikọlu ti o le fa iṣẹ ti a ko fẹ fun ẹrọ naa.

ICES-003 Kilasi B Akiyesi – Avis NMB-003 Kilasi B:
Ẹrọ oni-nọmba Kilasi B yii ni ibamu pẹlu ICES-003 ti Ilu Kanada.

LE ICES-3 (B) / NMB-3 (B)
Gbólóhùn Ifihan Radiation RF:
This product complies with ISED radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated at a minimum distance of 20 cm between the radiator and the human body.
This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter except in accordance with ISED multi-transmitter product procedures.
Ẹrọ yii ni ibamu pẹlu koodu Aabo Ilera ti Canada. Olupilẹṣẹ ẹrọ yii yẹ ki o rii daju pe itankalẹ RF ko ni itusilẹ ju ibeere Ilera Canada lọ.

FAQ