Effon M2 Barcode Reader User Guide

Effon M2 Barcode Reader

Awọn pato

Eto & Lo

1. Agbara lori: Press either side button to turn on the device.
2. Agbara kuro: By default it shuts down after 5 minutes of sleep. To change shutdown behavior, scan the sleep-time setup barcode (or scan the Sun bayi barcode).
3. Initialize/reset: Ṣayẹwo awọn Bibẹrẹ Eto barcode to reset to initial settings.
4. Update version display: Ṣayẹwo awọn Àpapọ version alaye barcode to show version details.
5. Set output customization (optional): Use the relevant setup barcodes for prefix/suffix, end character, HID character case, and hide front/rear characters.
6. Configure Bluetooth (optional): After connecting Bluetooth, scan Yi Orukọ Bluetooth pada, then scan the desired Bluetooth name barcode; after canceling Bluetooth pairing, search again. To switch modes, scan the required Bluetooth mode barcode.
7. Mounting (optional): Adhere the metal plate to your phone/case, align the M2 slots to the plate, and slide upward until it clicks; to remove, hold the sliding button and slide the scanner downward.

Tan & Pa a

Tan-an:
Press either side button to turn on the device.

Paa:
By default, it will shut down after 5minutesofsleep.You can scan the setting code to turn off, or set the required sleep time.

Initialization settings &Versioninformation
To reset the scanner to its initial settings, scanthe“InitializeSettings” barcode below. Scanning the “DisplayVersionInformation” barcode will show the scanner’s versiondetails.

Prefix and suffix setting
Scan the “Prefix setting” or “Suffix setting” barcode, then scan the ADCII code of the desired prefix or suffix character.

Eto iyara gbigbe

Eto akoko orun

Storage mode setting

Set to hide front or rear characters
Scan the “Hide front character” or “Hide rear character” setup code first, then scan the barcode with the desired number of characters.

HID output character casesetting

Eto ede keyboard HID

Yi orukọ Bluetooth pada

• Step1: After connecting Bluetooth, scan the “Change Bluetooth Name” barcode.
• Step2: Scan the barcode for the Bluetooth name you wish to set, such as “Scanner123”. Finally, after canceling the Bluetooth pairing, perform a new Search to find the new Bluetooth name

Eto ipo Bluetooth
After scanning the required Bluetooth mode barcode, thescanner will switch to the corresponding mode.

Ipari eto kikọ

Iwọn didun ati eto motor

Toggle Bluetooth HIDkeyboardiniOS

Ṣe afihan ipele batiri

Iṣagbesori

1. Attach: Adhere the metal plate with fixing hooks to the back of your phone or phone case.
2. Align: Position the M2 scanner, aligning its slots with both ends of the metal plate.
3. Slide & Lock: Slide the M2 upward until you hear a “click,” indicating it is securely locked in place.

Dismounting

1. Unlock: Push the sliding button at the bottom of the M2 to the left and hold it in position.
2. Slide Off: While holding the button, slide the M2 downward to remove it from the plate.

Imọran:
The metal plate on your phone allows for quick and easy Reinstallation whenever needed.

Awọn iwọn 
90.3×62.4X14.O mm (LXWXH)

iwuwo:
49.5 giramu

Gbólóhùn FCC

Ẹrọ yii ni ibamu pẹlu apakan 15 ti Awọn ofin FCC. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:

1. ẹrọ yi le ma fa ipalara kikọlu, ati
2. Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa iṣẹ ti ko fẹ. Eyikeyi iyipada tabi awọn iyipada ti ko fọwọsi ni pato nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ohun elo naa.

AKIYESI:
Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni nọmba Kilasi B, ni ibamu si Apá 15 ti Awọn ofin FCC. Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to tọ si kikọlu ipalara ni fifi sori ibugbe kan. Ẹrọ yii n ṣe ipilẹṣẹ, nlo ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato. Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:

• Reorient tabi tun eriali gbigba pada.
• Mu iyatọ pọ si laarin ẹrọ ati olugba.
• So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ.
• Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.

Ẹrọ naa ti ni iṣiro lati pade ibeere ifihan RF gbogbogbo. Ẹrọ naa le ṣee lo ni ipo ifihan gbigbe laisi ihamọ.

Laasigbotitusita

• Scanner output not as expected (prefix/suffix, hidden characters, end character): Re-check the relevant setup codes and use the corresponding cancel procedure (e.g., scan the Prefix/Suffix setting barcode again to cancel, or scan the Fagilee ohun kikọ silẹ barcode).
• Need to restore default settings: Ṣayẹwo awọn Bibẹrẹ Eto barcode to reset the scanner to its initial settings.
• Bluetooth device name change didn’t take effect: The manual states that after initialization the Bluetooth name reverts to default. Also, after setting a new name, cancel Bluetooth pairing and perform a new search to find the updated Bluetooth name.
• Need to switch Bluetooth behavior: Scan the desired Bluetooth Mode Setting barcode; the scanner will switch to the corresponding mode.
• Power/sleep timing confusion: If the device is shutting down sooner than desired, scan the appropriate Eto Aago Orun barcode (e.g., 10 minutes, 30 minutes, or Maṣe sun).