HYPERKIN Competitor Wired Controller User Manual

HYPERKIN Competitor Wired Controller

O ṣeun fun riraasing the Hyperkin The Competitor for Xbox Series X|S, Xbox One, and Windows 10/11 PC – Wired Controller. For your safety and the safety of others, please carefully read this guide before using this product.

1. Plug the provided Type-C cable into the Type-C port located on the TOP of the Hyperkin Xenon.
2. Plug the other end of the cable into an available USB port on your Xbox Series X|S, Xbox One, PC or Steam OS.
3. The controller will vibrate.
4. Click the Nexus button.
5. The ring light will illuminate.

Alakoso rẹ ti ṣetan lati lo.

WAKING UP YOUR XBOX CONSOLE USING THE COMPETITOR

If The Competitor is plugged into an Xbox console, you may turn on the console by clicking the Nexus button on The Competitor. After doing so, the console will turn on and the controller Nexus button will illuminate (this may take a few seconds).

Alakoso rẹ ti ṣetan lati lo.

PROGRAMMABLE BACK BUTTONS (MAPPING)

To map a button to a back button, hold the Mode Button (marked “M”) on the back of the controller, and your desired back button (M1 or M2) at the same time. The Competitor will vibrate, and the ring light around the Nexus will begin to flash. Release the Mode Button and back button. The Competitor is now in “mapping mode”. Next, click the button you would like mapped to your desired back button. The Competitor will vibrate again, indicating that you have exited “mapping mode” and the selected button has been mapped to your desired back button.

PROGRAMMABLE BACK BUTTONS (UN-MAPPING)

To un-map a button from a back button, hold the Mode Button (marked “M”) and your desired back button. The Competitor will vibrate, and the ring light will begin to flash. Release the Mode Button and back button. The Competitor is now in “mapping mode”. Next, click the same back button. The Competitor will vibrate again, indicating that you have exited “mapping mode” and a button is no longer mapped to that back button.

BACK BUTTON LOCKS

To disable back buttons, slide the switches on the back of The Competitor inwards towards the “locked” indicator to lock the back buttons. Slide outwards to unlock.

REMOVEABLE STICK CAPS
Grip and remove the stick caps in an upward motion. To set new stick caps onto the sticks, align the smaller teeth on the stick caps with the notches on the stick. Press down on the stick caps until they click into place.

ORIKI
Connect your headset audio jack into the bottom of The Competitor.

Bọtini MIC MUTE
Double-tap the Mute Button (microphone symbol) on the front of The Competitor to mute the microphone on a connected headset. An orange glow indicates that your microphone is muted.

FCC akiyesi

Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni-nọmba Kilasi B, ni ibamu si Apá 15 ti Awọn ofin FCC. Awọn ifilelẹ wọnyi jẹ apẹrẹ ni fifi sori ibugbe. Ẹrọ yii n ṣe ipilẹṣẹ, nlo, ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato. Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:

• Reorient tabi tun eriali gbigba pada.
• Mu iyatọ pọ si laarin ẹrọ ati olugba.
• So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ.
• Kan si alagbata tabi onimọran tẹlifisiọnu redio ti o ni iriri tabi imeeli Atilẹyin@Hyperkin.com fun iranlowo. Awọn kebulu ti o ni aabo gbọdọ ṣee lo pẹlu apakan yii lati rii daju ibamu pẹlu awọn opin Kilasi B FCC.

Awọn iyipada tabi awọn iyipada si ẹyọkan ti a ko fọwọsi ni gbangba nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ohun elo yii.

Gbólóhùn ti ibamu pẹlu EU šẹ

Hyperkin Inc., located at 1939 West Mission Blvd, Pomona, CA 91766, declares under our sole responsibility that the product, Hyperkin Xenon Wired Controller, is in compliance with the essential requirements and other relevant provisions of Low Voltage šẹ (LVD) 2014/35/EU, RoHS šẹ 2011/65/EU, ati ki o gbe awọn CE siṣamisi.

Ikede ni kikun ti ibamu le ṣee beere nipasẹ imeeli:

• Imeeli: ibamu@hyperkin.com
• Orukọ Ile-iṣẹ: Hyperkin Inc.
• Adirẹsi: 1939 West Mission Blvd, Pomona, CA 91766

© 2026 Hyperkin Inc. Hyperkin® is a registered trademark of Hyperkin Inc. All rights reserved. All other trademarks are the property of their respective owners.