IN2 ACCESS CP-6638 Gilbert Alailowaya Loop Kit

Ilana itọnisọna Gilbert Alailowaya Loop Kit

Awọn eto ti wa ni kq a se aṣawari ati olugba kan. Ipilẹṣẹ akọkọ rẹ wa ni ibaraẹnisọrọ alailowaya ti aṣawari oofa ati olugba eyiti o ṣe irọrun fifi sori ẹrọ pupọ. Ti a ṣe apẹrẹ fun iṣọpọ daradara, emitter ti wa ni irọrun fi sori ẹrọ lori ilẹ, ni idaniloju iṣẹ ṣiṣe ti o gbẹkẹle ati ailewu. Olugba naa ni awọn abajade isọdọtun 2 fun awọn iṣẹ ṣiṣe ti wiwa itusilẹ ati aabo (iwaju ọkọ ayọkẹlẹ).

 Awọn Itọsọna Aabo

• Reaction time < 60ms
• Device with SELV/PELV Power Supply

Transmitter And Receiver Terminals

Typical Installation – Sliding gate

Typical Installation – Barrier

Receiver Output Connections

*Powered and safe system configuration

Receiver Led Indicator

Ibẹrẹ

1. Fi awọn batiri sii
2. Connect receiver power supply
3. Check option selectors
4. Carry out programming process (Point 7)
5. Install detector on gate/barrier
6. Ensure minimum distance of 1m
7. Install and wire receiver
8. Tan ipese agbara
9. Carry out calibration process (Point 8)
10. Test system on gate/barrier

Akiyesi: The kit is supplied with the transmitter and receiver pre-programmed as standard (skip 7 if single TX installed).

Ilana siseto

Eto afọwọṣe ti atagba (to apapọ awọn aṣawari 7 fun olugba)

Atunto iranti (awọn aṣawari ti a ti sọ di mimọ)

Calibration Process (To Be Carried Out When Detector Fixed Into Position)

* Lakoko awọn iṣẹju 120 wọnyi, awọn atagba so pọ pẹlu olugba ni atunṣe si wiwa ti wọn ni ni agbegbe wọn, mu awọn aye wọnyi bi iye ibẹrẹ.

Memori Full Atọka
Awọn ariwo pupọ fun iṣẹju-aaya 10 nigba igbiyanju lati ṣe akori atagba tuntun kan. Eto naa le fipamọ awọn atagba 7 fun ikanni kan.

Atọka Batiri Kekere
4 beeps each time a message is received from a programmed transmitter. Both, warning LED and buzzer are activated simultaneously.

Awọn Eto Aṣayan olugba

Awọn ipinlẹ wiwa

When a vehicle is first detected, both outputs are triggered. Shortly after the impulse output switches off until the sensor is full clear and another vehicle is detected. The presence output remains on as long as the vehicle is detected by the sensor. Once the vehicle has cleared the sensor, the presence output switches off. (NOTE: DIP 5 (ON) on the receiver enables a
5 sec switch off delay) If multiple detectors are used, the impulse output will switch every time the sensor is activated and deactivated but the presence remains switched as long as one sensor is covered.

Detector Variants

Above ground/ surface mount

Ni isalẹ ilẹ / ifibọ

Imọ ni pato

Sipesifikesonu	Awọn alaye
Receiver Supply Voltage	12/24 AC / DC
Batiri	2 x AA 3.6V lithium battery
Igbesi aye batiri	ọdun meji 4
Iranti olugba	7 transmitter per receiver
Awọn abajade olugba	2 Relays, Voltage free olubasọrọ
Receiver Power Consumption	0.5 W – 12 V / 1.2 W – 24 V
Ibiti o	50m
Awọn iwọn otutu ṣiṣẹ	-35°C si +55°C
Software	Kilasi A
Rated Transient Overvoltage	330V
Transmitter Power Consumption	Transmitting 17mA / Stand by 100uA
Aago lenu	Kere ju 60 ms

Awọn akọsilẹ fifi sori ẹrọ

• Installation, start-up, modification, and retrofitting of the system may only be carried out by a qualified person.
• Yipada si pa awọn ṣiṣẹ voltage before working on the system.
• The system doesn’t have fuse protection. It is recommended to include exterior protection minimum 100mA and maximum 250mA.
• If there is any doubt, it is advisable to perform a complete memory wipe (process 7).

Gilbert Wireless Vehicle Detection System

Itọsọna ibere ni kiakia
Itọsọna yii jẹ apẹrẹ lati ṣe iranlọwọ fun ọ lati ṣeto ati bẹrẹ lilo eto wiwa alailowaya rẹ pẹlu irọrun. Boya o n fi awọn sensọ sii ni papa ọkọ ayọkẹlẹ kan, oju opopona, tabi agbegbe iṣowo, Gilbert n pese igbẹkẹle, wiwa ọkọ ayọkẹlẹ gidi-akoko laisi iwulo fun wiwọ nla. Tẹle awọn igbesẹ ti o ṣe ilana ni isalẹ lati gba eto rẹ soke ati ṣiṣe ni iyara, ni idaniloju iṣẹ ṣiṣe to dara julọ ati deede lati ibẹrẹ.

Awọn ẹya ara ẹrọ bọtini

 

Loke ilẹ alailowaya lupu

1. Igbesẹ 1: Carefully mark the hole positions on the ground using the mounting base or template as a guide. Ensure correct alignment and that the wireless loop is level before continuing. Use an appropriate drill and bit suitable for the surface material to drill holes at the marked positions.
2. Igbesẹ 2: Position the wireless loop over the drilled holes, ensuring correct alignment. Insert the provided bolts through the holes in the base of the wireless loop and into the drilled holes in the ground. Using a suitable tool, tighten the bolts securely to ensure the detector is firmly anchored in place.
3. Igbesẹ 3: Once the AA batteries have been installed (supplied with unit), securely reattach the lid, ensuring it is properly sealed to protect against dust and moisture. With the unit fully assembled, proceed to run the calibration procedure as outlined in the instruction manual. This step is essential to ensure accurate vehicle detection and optimal performance.

Awọn ẹya ara ẹrọ bọtini

In-ground Wireless Loop

1. Igbesẹ 1: Using a core drill, carefully cut a hole in the ground’s surface to accommodate the in-ground wireless loop. Ensure the hole is sized correctly, allowing enough space for the wireless loop to sit flush with the surface.
2. Igbesẹ 2: Mark the hole positions using the mounting base as a guide, ensuring correct alignment and that the wireless loop is level. Drill holes into the ground at the marked points. Insert the provided bolts through the base and into the drilled holes. Using a suitable tool, tighten the bolts securely to anchor the unit. Ensure sealing components provided are used to maintain weather protection.
3. Igbesẹ 3: Ni kete ti awọn batiri AA ti fi sori ẹrọ (ti a pese pẹlu ẹyọkan), tun so ideri naa ni aabo, ni idaniloju pe o ti ni edidi daradara lati daabobo lodi si eruku ati ọrinrin.
4. Igbesẹ 4: Pẹlu ẹyọkan ti o pejọ ni kikun, tẹsiwaju lati ṣiṣe ilana isọdiwọn bi a ti ṣe ilana rẹ ninu afọwọṣe itọnisọna. Igbesẹ yii jẹ pataki lati rii daju wiwa ọkọ ayọkẹlẹ deede ati iṣẹ ṣiṣe to dara julọ.
5. Igbesẹ 5: Pada eyikeyi awọn ela ni ayika lupu alailowaya pẹlu ohun elo ti o dara lati rii daju iduroṣinṣin ati ṣe idiwọ titẹ omi fun fifọ ati fifi sori ni aabo.

Gilbert Loke-Ilẹ

• Gilbert Above-Ground (component): CP-6647
• Gilbert Above-Ground (Kit): CP-6639
• Olugba: CP-RX GILBERT

Gilbert Ni-Ilẹ

• Gilbert In-Ground (component): CP-6646
• Gilbert In-Ground (Kit): CP-6638
• Olugba: CP-RX GILBERT

IN2 Access & Control Ltd. Unit 6A Mile Oak, Maesbury Road Industrial Estate, Oswestry, Shropshire, SY10 8GA, UK

• Web: www.in2access.co.uk
• Imeeli: technical@in2access.co.uk
• Monday to Friday 08:30 – 17:00

Awọn ibeere Nigbagbogbo

Kini itọkasi fun batiri kekere ninu atagba?

When a message is received from a programmed transmitter, there will be 4 beeps, and both the warning LED and buzzer will be activated simultaneously.

Awọn atagba melo ni o le wa ni ipamọ fun ikanni kan?

The system can store up to 7 transmitters per channel for efficient operation.

Awọn iwe aṣẹ / Awọn orisun

IN2 ACCESS CP-6638 Gilbert Alailowaya Loop Kit [pdf] Ilana itọnisọna CP-6638 Apo Yipo Alailowaya Gilbert, CP-6638, Apo Yipo Alailowaya Gilbert, Ohun elo Loop Alailowaya, Ohun elo Loop

Awọn itọkasi

• Itọsọna olumulo