M5STACK ATOM S3U Itọnisọna Olumulo Alakoso Eto

ATOM S3U Eto Adarí

M5STACK ATOM-S3U

M5STACK ATOM-S3U jẹ ẹrọ ti o nlo chirún ESP32 S3 ati atilẹyin 2.4GHz Wi-Fi ati agbara-kekere Bluetooth ibaraẹnisọrọ alailowaya mode-meji.

Awọn pato

Awọn ilana Lilo ọja

Arduino IDE Oṣo

1. Ṣabẹwo si osise Arduino webAaye (https://www.arduino.cc/en/Main/Software) lati ṣe igbasilẹ package fifi sori ẹrọ fun ẹrọ ṣiṣe rẹ.
2. Ṣii Arduino IDE ki o lọ kiri si `File`->`Awọn ayanfẹ`->`Eto`
3. Da awọn wọnyi M5Stack Boards Manager URL to `Afikun Boards Manager URLs:' https://raw.githubusercontent.com/espressif/arduino-esp32/ghpages/package_esp32_dev_index.json
4. Lilö kiri si `Awọn irinṣẹ`-> `Apapọ:`->`Aṣakoso igbimọ…`
5. Wa fun `ESP32` ninu ferese agbejade, wa ki o tẹ `Fi sori ẹrọ’
6. Yan `Awọn Irinṣẹ`->`Agba:`->`ESP32-Arduino-ESP32 DEV Module`
7. Fi awakọ FTDI sori ẹrọ ṣaaju lilo: https://docs.m5stack.com/en/download

Serial Bluetooth

1. Ṣii Arduino IDE ki o ṣii example eto `File`->` Examples`->`Bluetooth Serial`->`Serial To Serial BT`.
2. So ẹrọ pọ mọ kọnputa ki o yan ibudo ti o baamu lati sun.
3. Lẹhin ipari, ẹrọ naa yoo ṣiṣẹ Bluetooth laifọwọyi, ati pe orukọ ẹrọ naa jẹ 'ESP32test`.
4. Lo ohun elo fifiranṣẹ ni tẹlentẹle Bluetooth lori PC lati mọ gbigbejade sihin ti data ni tẹlentẹle Bluetooth.
5. Eyi jẹ ẹya Mofiampsnippet koodu:

#include BluetoothSerial.h
#if !defined(CONFIG_BT_ENABLED) || !defined(CONFIG_BLUEDROID_ENABLED) #error Bluetooth is not enabled! Please run `make menuconfig` to and en able it #endif
BluetoothSerial SerialBT;
void setup() { Serial.begin(115200);
SerialBT.begin("ESP32test"); //Bluetooth device name
Serial.println("The device started, now you can pair it with bluetooth!"); }
void loop() { if (Serial.available()) { SerialBT.write(Serial.read()); } if (SerialBT.available()) { Serial.write(SerialBT.read()); } delay(20); }

Wifi wíwo

1. Ṣii Arduino IDE ki o ṣii example eto `File`->` Examples`-> `WIFI`->`WIFI wíwo`.
2. So ẹrọ pọ mọ kọnputa ki o yan ibudo ti o baamu lati sun.
3. Lẹhin ipari, ẹrọ naa yoo ṣiṣẹ ọlọjẹ WIFI laifọwọyi, ati pe abajade ọlọjẹ WIFI lọwọlọwọ le ṣee gba nipasẹ atẹle ibudo ni tẹlentẹle ti o wa pẹlu Arduino.
4. Eyi jẹ ẹya Mofiampsnippet koodu:

#include WiFi.h
void setup() {
Serial.begin(115200);
// Set WiFi to station mode and disconnect from an AP if it was previously connected
WiFi.mode(WIFI_STA);
WiFi.disconnect();
delay(100);
Serial.println("Setup done");
}
void loop() {
Serial.println("scan start");
// WiFi.scanNetworks will return the number of networks found
int n = WiFi.scanNetworks();
Serial.println("scan done");
if (n == 0) {
Serial.println("no networks found");
} else {
for (int i = 0; i < n; ++i) {
// Print SSID and RSSI for each network found
Serial.print(i + 1);
Serial.print(": ");
Serial.print(WiFi.SSID(i));
Serial.print(" (");
Serial.print(WiFi.RSSI(i));
Serial.print(")");
Serial.println((WiFi.encryptionType(i) == WIFI_AUTH_OPEN)?" ":"*");
delay(10);
}
}
Serial.println("");
// Wait a bit before scanning again
delay(5000);
}

ÌLÁRÒ

ATOM S3U jẹ igbimọ idagbasoke idanimọ ọrọ IoT ti o kere pupọ ati rọ, ni lilo chirún iṣakoso akọkọ Espresso'ESP32, ni ipese pẹlu agbara kekere meji `Xtensa® 32-bit LX6` microprocessors, igbohunsafẹfẹ akọkọ Titi di `240MHz`. O ni awọn abuda ti iwọn iwapọ, iṣẹ ṣiṣe to lagbara ati agbara kekere. USB-A ti a ṣepọ
ni wiwo, pulọọgi ati mu ṣiṣẹ, rọrun lati gbejade, ṣe igbasilẹ ati ṣatunṣe eto naa. Iṣepọ `Wi-Fi` ati awọn modulu 'Bluetooth', pẹlu gbohungbohun oni-nọmba ti a ṣe sinu SPM1423 (I2S), le ṣaṣeyọri gbigbasilẹ ohun afetigbọ, o dara fun ọpọlọpọ ibaraenisepo eniyan-kọmputa IoT, awọn oju iṣẹlẹ idanimọ titẹ ohun (STT)

ESP32 S3
ESP32-S3 jẹ eto-agbara MCU-lori-a-chip (SoC) ti o ṣe atilẹyin 2.4GHz Wi-Fi ati Bluetooth® LE ibaraẹnisọrọ alailowaya-meji. Chip naa ṣepọ awọn oluṣeto-meji-mojuto Xtensa® 32-bit LX7 iṣẹ-giga, awọn alabaṣe agbara kekere-kekere, Wi-Fi baseband, Bluetooth baseband, awọn modulu RF, ati awọn agbeegbe.

ESP32-S3 ṣepọ gbogbo awọn paati agbeegbe lainidi, pẹlu oscillator gara, filasi, awọn agbara àlẹmọ ati awọn ọna asopọ ibaamu RF ninu package ẹyọkan.
Fun wipe ko si miiran agbeegbe irinše ti wa ni lowo, module alurinmorin ati igbeyewo ti wa ni ko ti beere boya. Bi iru bẹẹ, ESP32-S3 dinku idiju ipese
pq ati ki o se Iṣakoso ṣiṣe. Pẹlu iwọn ultra-kekere rẹ, iṣẹ ṣiṣe to lagbara ati agbara agbara-kekere, ESP32-S3 jẹ ibamu daradara fun eyikeyi opin-aaye tabi awọn ohun elo ti o ṣiṣẹ batiri, gẹgẹbi ẹrọ itanna wearable, ohun elo iṣoogun, awọn sensosi ati awọn ọja IoT miiran.

Ọja ni pato

YARA BERE

ARDUINO IDE
Ṣabẹwo si osise Arduino webaaye (https://www.arduino.cc/en/Main/Software), Yan package fifi sori ẹrọ fun ẹrọ ṣiṣe tirẹ lati ṣe igbasilẹ.

1. Ṣii Arduino IDE, lilö kiri si `File`->`Awọn ayanfẹ`->`Eto`
2. Da awọn wọnyi M5Stack Boards Manager URL to `Afikun Boards Manager URLs:' https://raw.githubusercontent.com/espressif/arduino-esp32/ghpages/package_esp32_dev_index.json
3. Lilö kiri si `Awọn irinṣẹ`-> `Apapọ:`->`Aṣakoso igbimọ…`
4. Wa `ESP32` ninu ferese agbejade, ri i ki o si tẹ `Fi sori ẹrọ’
5. yan `Awọn irin-`->` Board:`-> `ESP32-Arduino-ESP32 DEV Module
6. Jọwọ fi awakọ FTDI sori ẹrọ ṣaaju lilo: https://docs.m5stack.com/en/download

BLUETOOTH SERIAL
Ṣii Arduino IDE ki o ṣii example eto `File`->` Examples`->`Bluetooth Serial`->`Serial To Serial BT`. So ẹrọ pọ mọ kọnputa ki o yan ibudo ti o baamu lati sun. Lẹhin ipari, ẹrọ naa yoo ṣiṣẹ Bluetooth laifọwọyi, ati pe orukọ ẹrọ naa jẹ 'ESP32test`. Ni akoko yii, lo ohun elo fifiranṣẹ ni tẹlentẹle Bluetooth lori PC lati mọ gbigbe sihin ti data ni tẹlentẹle Bluetooth.

Ọja WIFI wíwo

Ṣii Arduino IDE ki o ṣii example eto `File`->` Examples`-> `WIFI`->`WIFI wíwo`.
So ẹrọ pọ mọ kọnputa ki o yan ibudo ti o baamu lati sun. Lẹhin ipari, ẹrọ naa yoo ṣiṣẹ ọlọjẹ WIFI laifọwọyi, ati pe abajade ọlọjẹ WIFI lọwọlọwọ le ṣee gba nipasẹ atẹle ibudo ni tẹlentẹle ti o wa pẹlu Arduino.

Gbólóhùn FCC

Ẹrọ yii ni ibamu pẹlu apakan 15 ti Awọn ofin FCC.

Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:
Eyikeyi awọn iyipada tabi awọn iyipada ti ko fọwọsi ni pato nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ohun elo naa.
Akiyesi: Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni nọmba Kilasi B, ni ibamu si apakan 15 ti Awọn ofin FCC. Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to tọ si kikọlu ipalara ni fifi sori ibugbe kan. Ẹrọ yii n ṣe ipilẹṣẹ awọn lilo ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato. Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:

1. Ẹrọ yii le ma fa kikọlu ipalara, ati
2. Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa isẹ ti ko fẹ.

• Reorient tabi tun eriali gbigba pada.
• Mu iyatọ pọ si laarin ẹrọ ati olugba.
• So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ.
• Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.

Ohun elo yii ni ibamu pẹlu awọn opin ifihan itankalẹ FCC ti a ṣeto fun agbegbe ti a ko ṣakoso.
Ohun elo yii yẹ ki o fi sori ẹrọ ati ṣiṣẹ pẹlu aaye to kere ju 20cm laarin imooru & ara rẹ.