MOONS NPSUGMDHB Wireless Node Controller Owner’s Manual

MOONS NPSUGMDHB Wireless Node Controller

Awọn pato

• Customer’s Part Number:
• MOONS’ Part Number: 4696355000211
• Model: NPSUGMDHB
• P/N: A8768

Koko-ọrọ si iyipada laisi akiyesi

awọn apejuwe

• The Wireless Node Controllers can be installed in the lighting control box, lamp chamber or installed self-contained under eaves or other sheltered areas due to the solid metal enclosure.
• It is very small size and excellent waterproof.
• It can automatically identify different types of LED driver, such as 0-10V, DALI-2/D4i and DMX(RDM).
• Supports 2 channels 0-10V for color temperature adjustment.
• Supports RGBW color.
• Supports dynamic scenes and animations.
• It communicates with the gateway through a WPAN (Sub-GHz).
• Self-building and self-healing MESH Network.
• The sensor interface supports sensor access with digital and analog outputs.

Awọn ẹya ara ẹrọ

• Iwọn titẹ siitage:12-30VDC.
• Power consumption: < 1W.
• Wireless communication: IEEE 802.15.4-915MHz.
• Automatically identify dimming mode.
• DMX(RDM) master, up to 6 loads.
• DALI-2/D4i Single-Master Controller, up to 6 loads.
• 2 channels of 0-10V Dimmer, up to 4 loads each channel.
• RGBW color support
• Dynamic scenes and animations
• 1 channel of sensor sample igbewọle.
• Save several dimming plans.
• Firmware upgrade: OTA.
• Embedded communication encryption mechanism.
• Radio frequency certification: FCC
• Warranty: 5years.

Awọn abuda

 Awọn ẹya ara ẹrọ itanna
At 20 ℃, 50% RH, 100Kpa conditions.

Akiyesi:

1. In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.
2. Nigba ti input voltage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

Awọn ipo iṣẹ

EMC

Ijẹrisi

Data Mechanical

Awọn iwọn
Dimensions are provided in the diagrams above.

Eriali

 Awọn ẹya ẹrọ iyan

LABEL 

Product barcode information:

• The last 8 digits of SN represent the communication address of the product.
• A” indicates that this product operates in the American frequency band;
• The QR code shows the product’s communication address.

Awọn apejuwe iṣẹ

Awọn atọkun

WPAN Module

• Communicate with the Gateway. Transfer various instructions, such as: dimming command, upload power metering data, set parameters and query telemetries accordingly and so on.
• Wireless communication: IEEE 802.15.4-Sub-GHz.
• Embedded communication encryption mechanism.

Dimming
Once the device is powered up, it will automatically identify the dimming mode (DALI-2/D4i / DMX(RDM) /0-10V) of the connected load. After recognition, it will automatically report its own running dimming mode and perform necessary operation in this way.

Akiyesi: To achieve perfect recognition of the dimming type, it is recommended that the controller and the LED driver be powered on simultaneously, or the controller be powered on later than the LED driver.

0-10V Dimming

• If it is identified as 0-10V dimmer, it can support 2-channel independent 0-10V dimming, which can support adjusting the color temperature (tunable white LED driver and software configuration are required).
• The DIM-TO-OFF LED drivers should be used; the LED drivers’ output will turn off once the dimming voltage jẹ <0.5V.
• Support positive and negative logic dimming (configuration required).
• If each channel is connected to multiple LED drivers, the maximum output current of each channel is 10mA, and if the load current is >10mA, the output voltage will be not accurate.

Akiyesi: Nigba ti input voltage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

DMX(RDM)

• If identified as a DMX(RDM) master, it can support up to 6 loads (maximum 3 slots for each load) and can be automatically addressed to support RDM instructions.
• 4 loads are recommended.

DALI-2/D4i

• If identified as a DALI-2/D4i Single-Master Controller, up to 6 loads (one address for each load) can be supported, supporting IEC62386-101/103/251/252/253/351 (TYPE D).
• 4 loads are recommended.

Akiyesi:

• At least one of the DALI-2/D4i LED drivers needs to be set to supply power to the DALI bus.
• Maximum of 6 DALI-2/D4i LED Drivers, any DALI-2/D4i LED Drivers >4 will need the power supply disabled
• In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.

Sensọ Input

• 1 channel of sensor input interface.
• Sensors with 0-10V output can be accessed.
• Passive digital output can be accessed.
• Sensors must be configured in software before it is functional in system.

Awọn imọlẹ Atọka

Akiyesi: 

1.  Purple light indicates that the communication between node controller and LED driver is lost. This might be due to use wrong LED driver or LED driver is not power on or wiring error (for example the reverse connection of the DMX bus). Please check the wiring connection or the power-on status of the LED driver, and then re-power the node controller.

Fifi sori ẹrọ

For DALI-2/D4i applications with sensor

For DMX(RDM) applications with sensor 

For 0-10V Dim to off applications with sensor 

 For 0-10V Tunable white applications with sensor 

 Recommended installation of antenna interface 

 Recommended installation of M18 Antenna 

PEREPERE

Gbólóhùn FCC

Ẹrọ yii ni ibamu pẹlu Apá 15 ti Awọn ofin FCC. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:

1. Ẹrọ yii le ma fa kikọlu ipalara, ati
2. Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa isẹ ti ko fẹ.

Išọra: Olumulo ti wa ni ikilọ pe awọn iyipada tabi awọn iyipada ti ko fọwọsi ni gbangba nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ohun elo naa.

Akiyesi: Ẹrọ yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni-nọmba Kilasi B, ni ibamu si apakan 15 ti Awọn ofin FCC.

Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to tọ si kikọlu ipalara ni fifi sori ibugbe kan. Ẹrọ yii n ṣe ipilẹṣẹ awọn lilo ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato. Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:

• Reorient tabi tun eriali gbigba pada.
• Mu iyatọ pọ si laarin ẹrọ ati olugba.
• So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ.
• Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.

Lati ṣetọju ibamu pẹlu awọn itọnisọna Ifihan RF ti FCC, ohun elo yii yẹ ki o fi sori ẹrọ ati ṣiṣẹ pẹlu aaye to kere ju laarin 20cm imooru ara rẹ: Lo eriali ti a pese nikan.

CUSTOMER’S APPROVAL STAMP
Please sign back after your approval. The specifications will come into force when we receive purchase order.

Koko-ọrọ si iyipada laisi akiyesi
© 2024 MOONS’. All rights reserved. All content contained herein is subject to change without prior notice. More product documentation and MOONS’ terms and conditions are available at https://www.moonsindustries.com

History Version