Omada L3 Campus Stackable Managed Switch User Manual

Awọn akoonu tọju

1 L3Campus Stackable Managed Switch

2 Awọn pato

3 Awọn ilana Lilo ọja

3.1 Chapter 2: fifi sori

3.2 Abala 3: Asopọ

3.3 Chapter 4: iṣeto ni

4 FAQ

4.1 Q: What should I do if the LED indications show an error?

4.2 Awọn iwe aṣẹ / Awọn orisun

4.2.1 Awọn itọkasi

L3Campus Stackable Managed Switch

Awọn pato

Awoṣe: Omada Campus Stackable L3 Managed Switch
Front Panel: Mode Selection Button, Management Port, LED,
Console Port USB2.0 Port (Type-C/RJ45), 1G RJ45 Port, 10G SFP+ Slot
LED
Itọkasi LED:
- PWR1*: Green On (switch powered by PWR1), Off (PWR2
  disconnected or not working properly)
- PWR2: Green On (switch powered by PWR1 and PWR2 connected),
  Yellow On** (PWR2 powered), Off (PWR1 disconnected or not working
  daradara)
- LED SYS FAN: Green On (all fans work properly), Yellow On (not
  all fans work properly)
- MGMT: On (device linked to port), Flashing (transmitting or
  receiving data), Off (no device linked to port)
- MST: On (device linked to port), Flashing (transmitting or
  receiving data), Off (no device linked to port)

Awọn ilana Lilo ọja

Chapter 2: fifi sori

Ṣaaju ki o to bẹrẹ ilana fifi sori ẹrọ, rii daju pe o ni ohun gbogbo
the necessary tools and follow safety precautions.

Awọn akoonu idii: Check all items mentioned in
package.
Awọn iṣọra Aabo: Tẹle awọn itọnisọna si
rii daju fifi sori ailewu.
Awọn irinṣẹ fifi sori ẹrọ: Gather all tools required
fun fifi sori.
Fifi sori ọja: Tẹle igbesẹ-ni-igbesẹ
instructions provided in the manual for successful
fifi sori ẹrọ.

Abala 3: Asopọ

After installation, connect the switch to the network using
appropriate cables and ports as per your network setup.

Chapter 4: iṣeto ni

Configure the switch based on your requirements. You can choose
between Standalone Mode or Controller Mode as per your network
aini.

FAQ

Q: What should I do if the LED indications show an error?

A: If the LED indications suggest improper functioning, check
the power sources and connections. Refer to the troubleshooting
apakan ninu awọn Afowoyi fun siwaju iranlowo.

“`

View Fullscreen

Solusan Nẹtiwọọki Iṣowo
Fifi sori Itọsọna
Omada Campus Stackable L3 Managed Switch

Nipa Itọsọna Fifi sori ẹrọ yii
Itọsọna fifi sori ẹrọ yii ṣe apejuwe awọn abuda ohun elo, awọn ọna fifi sori ẹrọ ati awọn aaye ti o yẹ ki o lọ si lakoko fifi sori ẹrọ. Itọsọna fifi sori ẹrọ yii jẹ eto bi atẹle: Abala 1 Ibẹrẹ Ipin yii ṣe apejuwe awọn paati ita ti yipada. Chapter 2 Fifi sori Yi ipin sapejuwe bi o si fi awọn yipada. Chapter 3 Asopọ yi ipin sapejuwe bi o lati se awọn ti ara asopọ ti awọn yipada. Chapter 4 Iṣeto ni Yi ipin sapejuwe bi o lati tunto awọn yipada. Àfikún A Laasigbotitusita Àfikún B pato

Olugbo

Itọsọna Fifi sori yii jẹ fun:

Onimọ ẹrọ nẹtiwọki

Alakoso nẹtiwọki

Awọn apejọ
Diẹ ninu awọn awoṣe ti o ṣe afihan ninu itọsọna yii le ma si ni orilẹ-ede tabi agbegbe rẹ. Fun alaye tita agbegbe, ṣabẹwo https://www.omadanetworks.com/.
Awọn eeya ni Orí 2, Orí 3, ati Orí 4 jẹ fun awọn idi ifihan nikan. Yipada rẹ le yato ni irisi si eyiti a fihan.
· Poe isuna isiro da lori yàrá igbeyewo. Isuna agbara PoE gangan ko ni iṣeduro ati pe yoo yatọ nitori abajade awọn idiwọn alabara ati awọn ifosiwewe ayika.
· Itọsọna yii nlo awọn ọna kika pato lati ṣe afihan awọn ifiranṣẹ pataki. Tabili ti o tẹle ṣe atokọ awọn aami akiyesi ti a lo jakejado itọsọna yii.

Ranti lati ṣọra. Išọra tọka agbara eyiti o le ja si ibajẹ ẹrọ.
Ranti lati ṣe akiyesi. Akọsilẹ naa ni alaye iranlọwọ fun lilo ti ọja ti o dara julọ.

Iwe ti o jọmọ
Itọsọna Olumulo ati Itọkasi Itọkasi CLI ti ọja ti pese lori Ile -iṣẹ Gbigbawọle. Lati gba alaye ọja tuntun, ṣabẹwo si osise naa webAaye: https://support.omadanetworks.com/document/.

Awọn akoonu
Ori 1 Ifaara ———————- 01
1.1 Ọja Loriview …………………………………………………………………..01 1.2 Ifarahan………………………………………………………………………………………………………….01
Orí 2 Ìfisípò ————————- 12
2.1 Awọn akoonu idii ………………………………………………………………….12 2.2 Awọn iṣọra Aabo …………………………………………………………12 2.3 Awọn irinṣẹ fifi sori ẹrọ………………………………………………………………………………………………………………………………………………………………………………….14
Orí Kẹta Àkópọ̀ ————————- 3
3.1 Ethernet Port …………………………………………………………..22 3.2 10G SFP+/25G SFP28/100G QSFP28 Slot ………..22 3.3 Console Port ……………………………………………………………22 3.4 Verify Installation…………………………………………………….23 3.5 Power On ………………………………………………………………….24 3.6 Initialization………………………………………………………………24 3.7 Stack Topology ……………………………………………………….24
Ori 4 Iṣeto ——————– 27
4.1 Iṣeto ni Loriview........................................................................................................................
Àfikún A Laasigbotitusita —————- 32
Àfikún B —————— 33

Omada Campus Stackable L3 Managed Switch

Chapter 1 Ọrọ Iṣaaju

1.1 Ọja Loriview
Apẹrẹ fun iṣowo ati campus, Omada Campus Stackable L3 Managed Switch provides wire-speed performance and abundant L2 and L3 management features. It provides a variety of service features and multiple powerful functions with high security. The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks. Static Routing, RIP, OSPF, BGP, IS-IS, PIM-SM/DM/SSM, and ECMP come with abundant Layer 3 routing protocols that support a scalable network. Physically stacking for builtin redundancy and performance. Redundant power supplies and fans make it an ideal choice for reliable networking architecture. VRRP allows a group of switches to dynamically back up each other. ERPS supports rapid protection and recovery in a ring topology. MACsec, secure boot, ACL, 802.1x and Dynamic ARP Inspection provide robust security strategies. QoS and IGMP snooping/filtering optimize voice and video application. Link aggregation (LACP) increases aggregated bandwidth, optimizing the transport of business critical data. SNMP, RMON, WEB, Netconf and CLI Log-in bring abundant management policies. These switches integrate multiple functions with excellent performance, and is friendly to manage, which can fully meet the need of the users demanding higher networking performance. S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y is also a Power Sourcing Equipment (PSE*). The RJ45 ports that support Power over Ethernet (PoE*) function can automatically detect and supply power to those powered devices (PDs*) complying with IEEE 802.3af, IEEE 802.3at, and IEEE 802.3bt (only for S6500-24MPP4Y/S6500-48MPP6Y). *PSE: a device (switch or hub for instance) that provides power through an Ethernet cable. *PoE: This technology describes a system to transmit electrical power, along with data, to remote devices over standard twisted-pair cable in an Ethernet. *PD: a device powered by a PSE and thus consumes energy. Examples pẹlu awọn kamẹra nẹtiwọọki agbara, awọn aaye iwọle LAN alailowaya, awọn tẹlifoonu IP, awọn ibudo nẹtiwọọki, awọn kọnputa ti a fi sinu ati bẹbẹ lọ.
1.2 Ifarahan
Front Panel (The figure is for demonstration only. It may differ from your actual product. )
The front panel of S6500-24G4XF is shown as the following figure.
Bọtini Aṣayan Ipo
Port Management

LED

Console Port USB2.0 Port (Type-C/RJ45)

1G RJ45 ibudo

10G SFP+ Slot LED

The front panel of S6500-48G6XF is shown as the following figure.
Bọtini Aṣayan Ipo
Port Management

LED

Console Port USB2.0 Port (Type-C/RJ45)

1G RJ45 ibudo

10G SFP+ Slot LED

Ifaara 01

Omada Campus Stackable L3 Managed Switch

Itọkasi LED

PWR1*

PWR2

Alawọ ewe Lori

Paa

Alawọ ewe Lori

Yellow Lori**

Paa

Alawọ ewe Lori

Paa

Itọkasi
Yipada ni agbara nipasẹ PWR1. PWR2 ti ge asopọ tabi o ṣiṣẹ ni aibojumu.
Yipada ni agbara nipasẹ PWR1. PWR1 ati PWR2 ti sopọ.
Yipada ni agbara nipasẹ PWR2. PWR1 ti ge asopọ tabi o ṣiṣẹ ni aibojumu.
Yipada wa ni pipa tabi mejeeji PWR1 ati PWR2 ṣiṣẹ ni aibojumu.

LED SYS FAN
MGMT
MST
Port 1-24 of S6500-24G4XF/ Port 1-48 of S6500-48G6XF
(When the SPEED LED is on)
Port 1-24 of S6500-24G4XF/ Port 1-48 of S6500-48G6XF
(Nigbati LED STK wa ni titan)
Port 25-28 of S6500-24G4XF/ Port 49-54 of S6500-48G6XF ***

Itọkasi
Imọlẹ: Yipada ṣiṣẹ daradara. Tan tabi Paa: Yipada naa n ṣiṣẹ lainidi.
Green Lori: Gbogbo awọn onijakidijagan ṣiṣẹ daradara. Yellow Lori: Kii ṣe gbogbo awọn onijakidijagan ṣiṣẹ daradara.
Lori: Ẹrọ kan ti sopọ mọ ibudo. Imọlẹ: Gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo.
Lori: Ẹrọ naa n ṣiṣẹ bi oluyipada titunto si ni topology akopọ tabi o ṣiṣẹ ni ẹyọkan. Paa: Ẹrọ naa n ṣiṣẹ bi iyipada ọmọ ẹgbẹ ninu topology akopọ.
Green Lori: Nṣiṣẹ ni 1000 Mbps, ṣugbọn ko si iṣẹ-ṣiṣe. Imọlẹ alawọ ewe: Nṣiṣẹ ni 1000 Mbps ati gbigbe tabi gbigba data. Yellow Lori: Nṣiṣẹ ni 10Mbps/100 Mbps, ṣugbọn ko si iṣẹ-ṣiṣe. Imọlẹ ofeefee: Nṣiṣẹ ni 10Mbps/100 Mbps ati gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo ti o baamu.
Lori: Nọmba ibudo tọkasi ID kuro ni topology akopọ.
Green Lori: Nṣiṣẹ ni 10 Gbps, ṣugbọn ko si iṣẹ-ṣiṣe. Imọlẹ alawọ ewe: Nṣiṣẹ ni 10 Gbps ati gbigbe tabi gbigba data. Yellow Lori: Nṣiṣẹ ni 1 Gbps, ṣugbọn ko si iṣẹ ṣiṣe. Imọlẹ ofeefee: Nṣiṣẹ ni 1 Gbps ati gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo ti o baamu.

*PWR1 is the primary power supply and it takes priority over PWR2. When the device is powered by PWR1, PWR2 will be working in the backup mode.
** Nigbati awọn mejeeji PWR1 ati PWR2 ṣiṣẹ daradara ati awọn yipada ni agbara nipasẹ PWR1, o gba 10-20 aaya fun LED PWR2 (ofeefee) lati jade lẹhin PWR2 ti wa ni unpluged.
***All 10 Gbps SFP+ slots can be used as uplink ports or stacking ports. When used as stacking ports, the slots need to run at the highest speed.

02 ifihan

Omada Campus Stackable L3 Managed Switch The front panel of S6500-24GP4XF is shown as the following figure.

Bọtini Aṣayan Ipo
Port Management
LED Console Port USB2.0 Port (Type-C/RJ45)

1G RJ45 ibudo

10G SFP+ Slot LED

Ni iwaju nronu ti S6500-48GP6XF ti han bi awọn wọnyi olusin.

Bọtini Aṣayan Ipo
Port Management
LED Console Port USB2.0 Port (Type-C/RJ45)

1G RJ45 ibudo

10G SFP+ Slot LED

The front panel of S6500-24M4Y is shown as the following figure.

Bọtini Aṣayan Ipo
Port Management
LED Console Port USB2.0 Port (Type-C/RJ45)

2.5G RJ45 ibudo

25G SFP28 Slot LED

The front panel of S6500-24MPP4Y is shown as the following figure.

Bọtini Aṣayan Ipo
Port Management
LED Console Port USB2.0 Port (Type-C/RJ45)

2.5G RJ45 ibudo

25G SFP28 Slot LED

Ifaara 03

Omada Campus Stackable L3 Managed Switch The front panel of S6500-48M6Y is shown as the following figure.

Bọtini Aṣayan Ipo
Port Management

LED Console Port USB2.0 Port (Type-C/RJ45)

2.5G RJ45 ibudo

The front panel of S6500-48MPP6Y is shown as the following figure.

25G SFP28 Slot LED

Bọtini Aṣayan Ipo
Port Management
LED Console Port USB2.0 Port (Type-C/RJ45)

2.5G RJ45 ibudo

25G SFP28 Slot LED

LED Indication LED
PWR1* PWR2
SYS FAN PoE MAX
(For S6500-24GP4XF, S6500-48GP6XF, S6500-24MPP4Y, S6500-48MPP6Y)
MGMT
MST

04 ifihan

Omada Campus Stackable L3 Managed Switch

LED

Itọkasi

Port 1-24 of S6500-24GP4XF/
Port 1-48 of S6500-48GP6XF
(When the SPEED LED is on)

Green Lori: Nṣiṣẹ ni 1000 Mbps, ṣugbọn ko si iṣẹ-ṣiṣe. Imọlẹ alawọ ewe: Nṣiṣẹ ni 1000 Mbps ati gbigbe tabi gbigba data. Yellow Lori: Nṣiṣẹ ni 10Mbps/100 Mbps, ṣugbọn ko si iṣẹ-ṣiṣe. Imọlẹ ofeefee: Nṣiṣẹ ni 10Mbps/100 Mbps ati gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo ti o baamu.

Port 1-24 of S6500-24M4Y & S6500-24MPP4Y/
Port 1-48 of S6500-48M6Y & S6500-48MPP6Y
(When the SPEED LED is on)

Green On: Running at 2.5 Gbps, but no activity. Green Flashing: Running at 2.5 Gbps and transmitting or receiving data. Yellow On: Running at 10 Mbps/100 Mbps/1000 Mbps, but no activity. Yellow Flashing: Running at 10 Mbps/100 Mbps/1000 Mbps and transmitting or receiving data. Off: No device is linked to the corresponding port.

Port 1-24 of S6500-24GP4XF, S6500-24M4Y &
S6500-24MPP4Y/
Port 1-48 of S6500-48GP6XF, S6500-48M6Y &
S6500-48MPP6Y
(Nigbati LED STK wa ni titan)

Lori: Nọmba ibudo tọkasi ID kuro ni topology akopọ.

Port 1-24 of S6500-24GP4XF & S6500-24MPP4Y/
Port 1-48 of S6500-48GP6XF & S6500-48MPP6Y
(Nigbati PoE LED wa ni titan)

Green On: The port is supplying power normally. Green Flashing: The supply power exceeds the correponding port’s maximum power. Yellow On: Overload or short circuit is detected. Off: Not providing PoE power on the port

Port 25-28 of S6500-24GP4XF/ Port 49-54 of S6500-48GP6XF ***

Green Lori: Nṣiṣẹ ni 10 Gbps, ṣugbọn ko si iṣẹ-ṣiṣe. Imọlẹ alawọ ewe: Nṣiṣẹ ni 10 Gbps ati gbigbe tabi gbigba data. Yellow Lori: Nṣiṣẹ ni 1 Gbps, ṣugbọn ko si iṣẹ ṣiṣe. Imọlẹ ofeefee: Nṣiṣẹ ni 1 Gbps ati gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo ti o baamu.

Port 25-28 of S6500-24M4Y & S6500-24MPP4Y/
Port 49-54 of S6500-48M6Y & S6500-48MPP6Y***

Green Lori: Nṣiṣẹ ni 25 Gbps, ṣugbọn ko si iṣẹ ṣiṣe. Imọlẹ alawọ ewe: Nṣiṣẹ ni 25 Gbps ati gbigbe tabi gbigba data. Yellow Lori: Nṣiṣẹ ni 1 Gbps/10 Gbps, ṣugbọn ko si iṣẹ ṣiṣe. Imọlẹ ofeefee: Nṣiṣẹ ni 1 Gbps/10 Gbps ati gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo ti o baamu.

*By default, S6500-24GP4XF is shipped with a PSM500-AC power supply module, S6500-24M4Y/S650048M6Y is shipped with a PSM550-AC power supply module, and S6500-48GP6XF/S6500-24MPP4Y/ S6500-48MPP6Y is shipped with a PSM900-AC power supply module. One more power supply module needs to be purchased separately.
**By default, both PWR1 and PWR2 will work simultaneously in the load sharing mode. They can also work simultaneously in the redundant power supply mode: for S6500-24GP4XF/S6500-48GP6XF/S650024MPP4Y/S6500-48MPP6Y, you can specify the primary power supply and the backup power supply according to your needs; for S6500-24M4Y/S6500-48M6Y, you can only set PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply.
***All 10 Gbps SFP+ slots and 25 Gbps SFP28 slots can be used as uplink ports or stacking ports. When used as stacking ports, the slots need to run at the highest speed.

Ifaara 05

Omada Campus Stackable L3 Managed Switch The front panel of S7500-26XF6Y is shown as the following figure.
Port Management

LED

Console Port USB3.0 Port

(RJ45/Irú-C)

Aṣayan Ipo

Bọtini

10G SFP+ Slot (Port 1-26)

The front panel of S7500-48XF4C is shown as the following figure.

LED 25G SFP28 Slot (Port 27-32)

Bọtini Aṣayan Ipo
Port Management
LED Console Port USB3.0 Port (Type-C/RJ45)

10G SFP+ Slot (Port 1-48)

The front panel of S7500-24Y4C is shown as the following figure.

100G QSFP28 Slot LED (Port 49-52)

Port Management

LED

Ibudo USB3.0

Port Console

(RJ45/Irú-C)

Bọtini Aṣayan Ipo

25G SFP28 Iho

LED

( Port 1-24 )

The front panel of S7500-48Y8C is shown as the following figure.

100G QSFP28 Iho (Port 25-28)

LED Mode Selection Button

25G SFP28 Slot (Port 1-48)

06 ifihan

100G QSFP28 Iho (Port 49-56)

Omada Campus Stackable L3 Managed Switch The front panel of S7500-32C is shown as the following figure.

Bọtini Aṣayan Ipo
LED ibudo isakoso
Ibudo USB3.0

Console Port (Type-C/RJ45)

100G QSFP28 Iho

LED

Note: S7500-24Y4C and S7500-48Y8C are designed for installation in Network Telecommunications Facilities (NTFs) where ambient temperature and humidity are controlled.

LED Indication LED
PWR1* PWR2
SYS FAN
MGMT
MST
Port 1-26 of S7500-26XF6Y/ Port 1-48 of S7500-48XF4C
(Nigbati SPD LED wa ni titan)
Port 1-24 of S7500-24Y4C/ Port 1-48 of S7500-48Y8C
(When the SPD/SPEED LED is on)

Itọkasi
Green On: The power supply works properly. Green Flashing: The power supply module is not plugged in properly or not compatible with the switch. Yellow On: The power supply works properly but the switch is powered by the other power supply.** Yellow Flashing: The power supply module is plugged in properly but there’s is no AC power input; abnormal power supply. Off: No power supply module is inserted.
Imọlẹ: Yipada ṣiṣẹ daradara. Tan tabi Paa: Yipada naa n ṣiṣẹ lainidi.
Alawọ ewe: Gbogbo awọn onijakidijagan ṣiṣẹ daradara. Yellow: Kii ṣe gbogbo awọn onijakidijagan ṣiṣẹ daradara.
Lori: Ẹrọ kan ti sopọ mọ ibudo. Imọlẹ: Gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo.
Akiyesi:
For S7500-48Y8C, this LED lights green at 1 Gbps and orange at sub-1 Gbps.
Lori: Ẹrọ naa n ṣiṣẹ bi oluyipada titunto si ni topology akopọ tabi o ṣiṣẹ ni ẹyọkan. Paa: Ẹrọ naa n ṣiṣẹ bi iyipada ọmọ ẹgbẹ ninu topology akopọ.
Green Lori: Nṣiṣẹ ni 10 Gbps, ṣugbọn ko si iṣẹ-ṣiṣe. Imọlẹ alawọ ewe: Nṣiṣẹ ni 10 Gbps ati gbigbe tabi gbigba data. Yellow Lori: Nṣiṣẹ ni 1 Gbps, ṣugbọn ko si iṣẹ ṣiṣe. Imọlẹ ofeefee: Nṣiṣẹ ni 1 Gbps ati gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo ti o baamu.
Green Lori: Nṣiṣẹ ni 25 Gbps, ṣugbọn ko si iṣẹ ṣiṣe. Imọlẹ alawọ ewe: Nṣiṣẹ ni 25 Gbps ati gbigbe tabi gbigba data. Yellow Lori: Nṣiṣẹ ni 1 Gbps/10 Gbps, ṣugbọn ko si iṣẹ ṣiṣe. Imọlẹ ofeefee: Nṣiṣẹ ni 1 Gbps/10 Gbps ati gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo ti o baamu.

Ifaara 07

Omada Campus Stackable L3 Managed Switch

LED

Itọkasi

Port 27-32 of S7500-26XF6Y ***
(Nigbati SPD LED wa ni titan)

Port 49-52 of S7500-48XF4C/
Port 25-28 of S7500-24Y4C/ Port 49-56 of S7500-48Y8C/ Port 1-32 of S7500-32C***
(When the SPD/SPEED LED is on)

Green Lori: Nṣiṣẹ ni 100 Gbps, ṣugbọn ko si iṣẹ-ṣiṣe. Imọlẹ alawọ ewe: Nṣiṣẹ ni 100 Gbps ati gbigbe tabi gbigba data. Yellow Lori: Nṣiṣẹ ni 40 Gbps, ṣugbọn ko si iṣẹ ṣiṣe. Imọlẹ ofeefee: Nṣiṣẹ ni 40 Gbps ati gbigbe tabi gbigba data. Pipa: Ko si ẹrọ ti o sopọ mọ ibudo ti o baamu.
Akiyesi:
For S7500-48XF4C/S7500-48Y8C/S7500-32C, the indication above applies only when the 100 Gbps QSFP28 slots work with common cables. When the slots work with 1-to-4 breakout cables, a single slot is split into four 25 Gbps interfaces. In such scenario, the LED will light green only when all four interfaces are working at 25 Gbps (maximum speed), otherwise it will light yellow. When no device is connected to any of the four interfaces, the LED will be off. (The 100 Gbps QSFP28 slots will support 1-to-4 breakout cables in a future software release.)

Port 1-32 of S7500-26XF6Y/
Port 1-48 of S7500-48XF4C/ Port 1-28 of S7500-24Y4C/ Port 1-56 of S7500-48Y8C
(Nigbati LED STK wa ni titan)

Lori: Nọmba ibudo tọkasi ID kuro ni topology akopọ.

*By default, S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C/S7500-48Y8C/S7500-32C is shipped with a PSM550-AC power supply module installed respectively. One more power supply module needs to be purchased separately. **By default, both PWR1 and PWR2 will work simultaneously in the load sharing mode. They can also work simultaneously in the redundant power supply mode with PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply. ***All 25 Gbps SFP28 slots of S7500-26XF6Y and 100 Gbps QSFP28 slots of S7500-48XF4C/S7500-24Y4C/ S7500-48Y8C/S7500-32C can be used as uplink ports or stacking ports. When used as stacking ports, the slots need to run at the highest speed.
Port Introduction (The Management Port, Console Ports, and USB Ports of S7500-48Y8C are located on the rear panel.)
Port Management Apẹrẹ lati so ẹrọ fun isakoso nipasẹ web, CLI or SNMP. Do not connect this port to any outdoor device, as this may induce surge and lightning damage. Console Port Designed to connect with a computer for monitoring and configuring the switch. When the switch has an RJ45 console port and a Type-C console port, console input is active on only one console port at a time. By default, the Type-C connector takes priority over the RJ45 connector, or you can change the priority through the web. Do not connect this port to any outdoor device, as this may induce surge and lightning damage. USB Port Designed to install the USB flash disk for data storage. 1000M RJ45 Port Designed to connect to the device with a bandwidth of 10Mbps, 100 Mbps or 1000 Mbps. For PoE switches, the port can also provide power for PDs.

08 ifihan

Omada Campus Stackable L3 Managed Switch
2.5G RJ45 Port Designed to connect to the device with a bandwidth of 10 Mbps, 100 Mbps, 1000 Mbps or 2.5 Gbps. For PoE switches, the port can also provide power for PDs. 10G SFP+ Slot Designed to install the 10 Gbps/1 Gbps optical module. 25G SFP28 Slot Designed to install the 25 Gbps/10 Gbps/1 Gbps optical module. 100G QSFP28 Slot Designed to install the 100 Gbps/40 Gbps optical module. Port Feature

Awoṣe

1000M

2.5G 10G SFP+ 25G SFP28 100G QSFP28 Management Console USB

RJ45 Port RJ45 Port Slot

Iho

Ibudo

Port Port

S6500-24G4XF

S6500-48G6XF

S6500-24GP4XF

S6500-48GP6XF

S6500-24M4Y

S6500-24MPP4Y

S6500-48M6Y

S6500-48MPP6Y

S7500-26XF6Y

S7500-48XF4C

S7500-24Y4C

S7500-48Y8C

S7500-32C

Rear Panel (The figure is for demonstration only. It may differ from your actual product. )
The rear panel of S6500-24G4XF/S6500-48G6XF is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Kensington Security Slot Grounding Terminal Power Socket

Locking Strap Slot

Akiyesi: PWR1 jẹ ipese agbara akọkọ ati pe o gba pataki lori PWR2.

Ifaara 09

Omada Campus Stackable L3 Managed Switch
The rear panel of S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Iho Aabo Kensington

LED

Ebute ilẹ

Module Ipese Agbara

LED

Locking Strap Slot

Note: By default, S6500-24GP4XF is shipped with a PSM500-AC power supply module, and S650048GP6XF/S6500-24MPP4Y/S6500-48MPP6Y is shipped with a PSM900-AC power supply module. One more power supply module needs to be purchased separately. Both PWR 1 and PWR2 can work simultaneously, or you can specify the primary power supply and the backup power supply according to your needs. Generally, the primary power supply takes priority over the backup power supply.
The rear panel of S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Ebute ilẹ

LED

Power Supply Module Locking Strap Slot

LED

Iho Aabo Kensington

Awọn ru nronu ti S7500-48Y8C ti han bi awọn wọnyi olusin. Nọmba naa wa fun awọn idi ifihan nikan. Yipada rẹ le yato ni irisi si eyiti a fihan.

Ebute ilẹ

LED

Titiipa Okun

Iho

Module Ipese Agbara

10 ifihan

ManagemeC(nTtoyPnposeor-tCle/RPJoU4rt5S)B3P.o0wPeorrSt upplyLoMcokdiSnulgoletStraLpED

Omada Campus Stackable L3 Managed Switch
Note: By default, the device is shipped with a PSM550-AC power supply module installed. One more power supply module needs to be purchased separately. When the switch has two power supply modules installed, both PWR1 and PWR2 will work simultaneously in the load sharing mode by default. They can also work simultaneously in the redundant power supply mode with PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply.
The rear panel of S7500-32C is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

LED LED
Locking Strap Slot
Power Ipese Module Kensington Aabo Iho

Ebute ilẹ

LED
Locking Strap Slot

Module Ipese Agbara

Note: By default, the device is shipped with a PSM550-AC power supply module installed. One more power supply module needs to be purchased separately. When the switch has two power supply modules installed, both PWR1 and PWR2 will work simultaneously in the load sharing mode by default. They can also work simultaneously in the redundant power supply mode with PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply.
Power Supply Module The pluggable power supply module PSM500-AC/PSM900-AC/PSM550-AC is an AC-input power supply module. It can convert the input voltage to 53.5 V (12 V for PSM550-AC) with the maximum output power of 500 W/900 W/550 W respectively. Kensington Security Slot Secure the lock (not provided) into the security slot to prevent the device from being stolen.
Grounding Terminal The switch already comes with lightning protection mechanism. You can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable. For detailed lightning protection measures, refer to the Lightning Protection Guide from: https://support.omadanetworks.com/r/1004/. Locking Strap Slot Remove the instruction label and insert the AC power cable locking strap into the slot to secure the power cable.

Ifaara 11

Omada Campus Stackable L3 Managed Switch

Chapter 2 fifi sori

2.1 Package Awọn akoonu

Rii daju pe package ni awọn nkan wọnyi ninu. Jọwọ kan si olupin rẹ, ti eyikeyi ninu awọn ohun ti a ṣe akojọ ba bajẹ tabi sonu. Awọn isiro wa fun ifihan nikan. Awọn ohun gangan le yato ni irisi ati opoiye lati ti fihan.

Yipada

Okun Agbara ati Okun Console

Fifi sori Itọsọna
Solusan Nẹtiwọọki Iṣowo
Fifi sori Itọsọna
Omada Campus Stackable L3 Managed Switch

Iṣagbesori Biraketi, skru ati roba Ẹsẹ

2.2 Awọn iṣọra aabo
Lati yago fun eyikeyi bibajẹ ẹrọ ati ipalara ti ara ti o fa nipasẹ lilo aibojumu, o yẹ ki o pa awọn ofin wọnyi mọ.
Awọn iṣọra Aabo Jeki agbara si pipa lakoko fifi sori ẹrọ. Wọ okun ọwọ ọwọ idena ESD, ati rii daju pe okun ọwọ ni olubasọrọ awọ to dara ati pe o jẹ
daradara lori ilẹ. Lo okun agbara nikan ti a pese pẹlu iyipada. Rii daju wipe awọn ipese voltage ibaamu awọn pato itọkasi lori ru nronu ti awọn
yipada. Rii daju wipe awọn yipada ti wa ni ti fi sori ẹrọ ni kan daradara-ventilated iho ati awọn oniwe-fentilesonu iho ni ko
dina. Ma ṣe ṣi tabi yọ ideri ti yipada kuro. Ṣaaju ki o to nu ẹrọ naa, ge ipese agbara kuro. Ma ṣe sọ di mimọ nipasẹ asọ ti omi, ati rara
use any other liquid cleaning method. Place the device with its bottom surface facing downwards. Only instructed person or skilled person can be allowed to install, replace, or service this device.
Awọn ibeere Aaye
Iwọn otutu / Ọriniinitutu

12 fifi sori ẹrọ

Omada Campus Stackable L3 Managed Switch Keep the equipment room at an appropriate level of temperature and humidity. Too much or too little humidity may lead to bad insulation, leakage of electricity, mechanical property changes, and corrosion. High temperatures may accelerate aging of the insulation materials, significantly shortening the service life of the device. To find out the best temperature and humidity conditions for the device, check the Appendix B Specifications. Clearness
Eruku ti a kojọpọ lori yipada le gba nipasẹ ina aimi ati abajade ni olubasọrọ ti ko dara ti awọn aaye olubasọrọ irin. Diẹ ninu awọn igbese ti a ti gbe fun ẹrọ lati yago fun ina aimi, ṣugbọn ina aimi ti o lagbara pupọ le fa ibajẹ apaniyan si awọn eroja itanna lori igbimọ Circuit inu. Lati yago fun ipa ti ina aimi lori iṣẹ ti yipada, so pataki pupọ si awọn nkan wọnyi: Pa ẹrọ naa nigbagbogbo, ki o jẹ ki afẹfẹ inu ile mọ. Jeki ẹrọ naa ni ilẹ daradara ati rii daju pe a ti gbe ina aimi. Itanna kikọlu
Awọn eroja itanna pẹlu agbara ati inductance lori ẹrọ le ni ipa nipasẹ awọn kikọlu ita, gẹgẹbi itujade ti a ṣe nipasẹ iṣakojọpọ agbara, idapọ inductance, ati idapọ impedance. Lati dinku awọn kikọlu, rii daju pe o ṣe awọn iwọn wọnyi: Lo ipese agbara ti o le ṣe àlẹmọ kikọlu imunadoko lati akoj agbara. Jeki ẹrọ naa jinna si igbohunsafẹfẹ giga ati awọn ẹrọ ti o lagbara lọwọlọwọ gẹgẹbi gbigbe redio
ibudo. Lo idabobo itanna nigba pataki. Monomono Idaabobo
Fifi sori 13

Omada Campus Stackable L3 Managed Switch
Lalailopinpin voltage awọn sisanwo le jẹ iṣelọpọ lẹsẹkẹsẹ nigbati manamana ba waye ati afẹfẹ ninu ọna itusilẹ ina le jẹ kikan lesekese si 20,000 °C. Niwọn bi lọwọlọwọ lọwọlọwọ ti lagbara to lati ba awọn ẹrọ itanna jẹ, awọn igbese aabo monomono ti o munadoko diẹ sii yẹ ki o mu. Rii daju pe agbeko ati ẹrọ ti wa ni ilẹ daradara. Rii daju pe iho agbara ni olubasọrọ to dara pẹlu ilẹ. Jeki a reasonable cabling eto ki o si yago induced manamana. Lo ifihan SPD (Ẹrọ Aabo Aabo) nigbati o ba n ṣe onirin ni ita.
Akiyesi: Fun alaye awọn ọna aabo monomono, tọka si Itọsọna Idaabobo Imọlẹ lati: https://support.omadanetworks.com/r/1004/. Aaye fifi sori ẹrọ
When installing the device on a rack or a flat workbench, attach much importance to the following items: Install the device with its bottom surface facing down only. This equipment is not suitable for use in locations where children are likely to be present. The rack or workbench is flat, stable, and sturdy enough to support the weight of 9.5 kg at least. The rack or workbench has a good ventilation system. The equipment room is well ventilated. The rack is well grounded. Keep the device less than 1.5 meters away from the power socket.
2.3 Awọn irinṣẹ fifi sori ẹrọ
Phillips screwdriver ESD-gbèndéke ọwọ kebulu
Akiyesi: Awọn irinṣẹ wọnyi ko si pẹlu ọja wa. Ti o ba nilo, o le ra wọn lọtọ.
2.4 ọja fifi sori
Yipada jẹ apẹrẹ pẹlu ẹya-ara ifasilẹ ooru iwaju-si-ẹhin. Nigbati o ba ṣiṣẹ, afẹfẹ n kaakiri bi a ṣe han ni isalẹ. Fun ifasilẹ ooru to dara julọ, jọwọ fi ẹrọ naa sori ẹrọ ni agbegbe ti o ni afẹfẹ daradara ki o si fi 5 si 10 cm awọn ela ni ayika ẹrọ naa.
14 fifi sori ẹrọ

olusin 2-1

Afẹfẹ Circulation

Omada Campus Stackable L3 Managed Switch

Fifi sori tabili

Lati fi ẹrọ naa sori tabili tabili, tẹle awọn igbesẹ:
1. Ṣeto ẹrọ lori ilẹ pẹlẹbẹ ti o lagbara to lati ṣe atilẹyin gbogbo iwuwo ti ẹrọ pẹlu gbogbo awọn paipu.

2. Yọ awọn iwe ifẹhinti lẹ pọ lati awọn ẹsẹ roba.

3. So awọn ẹsẹ rọba si isalẹ ti ẹrọ naa lati ṣe idiwọ fun yiyọ nigbati a gbe sori tabili tabili kan.

olusin 2-2

Fifi sori tabili

Ẹsẹ Isalẹ ti Ogbontarigi Ẹrọ

Agbeko fifi sori

Apoti naa pẹlu awọn orisii 6 ti awọn biraketi iṣagbesori agbeko oriṣiriṣi, awọn aworan wọn jẹ afihan ni isalẹ ati pe o le yato si awọn ọja gangan.

olusin 2-3

Iṣagbesori Biraketi

dabaru Iho Ẹgbẹ 2

Bracket D Bracket C Bracket B Bracket A

dabaru Iho Ẹgbẹ 1
dabaru Iho Ẹgbẹ 3

Biraketi F

Screw Hole Group 4-2 (for device with 420mm depth)

dabaru Iho Ẹgbẹ 5

Dabaru Iho

Ẹgbẹ 4-1

Screw Hole Group 4-3

(for device with 380mm depth)

(for device with

460mm depth)

Akori E

Fifi sori 15

Omada Campus Stackable L3 Managed Switch

Before installing the device in an EIA standard-sized, 19-inch rack, please check the efficiency of the grounding system and the stability of the rack, then wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded. Bracket B, C & E have two adjustable ears, please measure the distance between the front-post rack and the rear-post rack, and determine a suitable mounting method from below:

Ọna

Afihan

Front: Bracket A Rear: Bracket D (Screw Hole Group 1) + Bracket B (Ear towards back)

Agbeko Ijinna
(For device with a depth of 380mm)

Agbeko Ijinna
(For device with a depth of 420mm)

Agbeko Ijinna
(For device with a depth of 460mm)

498-640mm 538-680mm 578-720mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 1) + Bracket C (Ear towards back)

477-498mm 517-538mm 557-578mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 2) + Bracket C (Ear towards back)

429-477mm 469-517mm 509-557mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 2) + Bracket C (Ear towards front)

410-429mm 450-469mm 490-509mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 3) + Bracket C (Ear towards back)

357-410mm 397-450mm 437-490mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 2) + Bracket B (Ear towards back)

282-410mm 322-450mm 362-490mm

16 fifi sori ẹrọ

Omada Campus Stackable L3 Managed Switch

Front: Bracket A Rear: Bracket F (Screw Hole Group 4) + Bracket E (Ear towards back)

555-936mm 555-936mm 555-936mm

Front: Bracket A Rear: Bracket F (Screw Hole Group 5) + Bracket E (Ear towards back)

743-1121mm 743-1121mm 743-1121mm

Lati fi ẹrọ naa sori ẹrọ, tẹle awọn itọnisọna ti a ṣalaye ni isalẹ:

1. Attach the M6 nuts to the racks.

olusin 2-4

Ni ifipamo M6 Eso

×8

2. Attach the mounting brackets (B, C or E) to the rear-post racks and secure them with the provided M6 screws, as illustrated in the following figure.

olusin 2-5

Fifi awọn biraketi sori Awọn agbeko

3. Attach the brackets A & D/F to the switch with the provided M3 screws.

Fifi sori 17

Omada Campus Stackable L3 Managed Switch

olusin 2-6

Fifi awọn biraketi lori Yipada

4. After the brackets are attached to the device, hold the switch with attached brackets up until it aligns with the brackets on the racks, and gently push the switch backwards until it is in place, then secure the device on the racks with M6 screws and fix brackets B/C or E to brackets D or F with M4 screws on both sides.

olusin 2-7

Fifi sori ẹrọ Yipada lori Awọn agbeko

Caution: Leave 5 to 10 cm gaps around the devices for air circulation. Avoid placing heavy things on the device. Mount devices in the order demonstrated above and ensure a certain clearance between devices for
the purpose of heat dissipation.

18 fifi sori ẹrọ

Omada Campus Stackable L3 Managed Switch

Agbara Ipese Module fifi sori

S6500-24GP4XF is shipped with a PSM500-AC power supply module installed, S6500-48GP6XF/ S6500-24MPP4Y/S6500-48MPP6Y is shipped with a PSM900-AC power supply module installed, and S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C/S7500-48Y8C/S750032C is shipped with a PSM550-AC power supply module installed. It looks like below, and the image may differ from your actual product.

olusin 2-8

Irisi ti Module Ipese Agbara

AC Power Okun Asopọmọra
FAN

Awọn agekuru idaduro

isediwon Handle

LED

Locking Strap Slot Release Handle

Ti o ba nilo lati ṣafikun module ipese agbara diẹ sii, jọwọ tẹle awọn igbesẹ:

1. Wọ okun ọwọ ọwọ idena ESD, ati rii daju pe o ni awọ ara ti o dara ati pe o wa ni ilẹ daradara.

2. Tẹ awọn isediwon mu ti awọn module pẹlu ọkan ọwọ, ki o si mu awọn isalẹ ti module lilo rẹ miiran ọwọ. Rọra Titari module ni pẹlú Iho guide iṣinipopada.

3. Tu awọn isediwon mu lati fix awọn ipese agbara module ni ibi.

olusin 2-9

Fifi Module Ipese Agbara sii

Imudani Tu silẹ

Caution: Do not plug the power cord until the power supply module installation is completed. When installing a power supply module, make sure it is set correctly in the operation of installation. Do not use too much force in the installation. If resistance is encountered or positions of the power
supply module appear larger during installation, you must first remove the module and then reinstall the module. If the Retainer Clips cannot spring up naturally and the power module is blocked, it may be due to the power supply module is not installed properly. Please check carefully.
The power supply module is designed with a locking strap slot. If you need to secure the power cable with the included locking strap, please follow the steps:
1. Wọ okun ọwọ ọwọ idena ESD, ati rii daju pe o ni awọ ara ti o dara ati pe o wa ni ilẹ daradara.
Fifi sori 19

Omada Campus Stackable L3 Managed Switch
2. Remove the instruction label on the AC power cable locking strap slot. 3. Attach the clamp to the AC power cable and insert the locking strap into the slot. 4. Adjust tightness and distance of the locking strap using clips to ensure the cable is securely fastened.
Figure 2-10 Installing the Locking Strap

Ti o ba nilo lati yọ module ipese agbara kuro, jọwọ tẹle awọn igbesẹ:
1. Wọ okun ọwọ ọwọ idena ESD, ati rii daju pe o ni awọ ara ti o dara ati pe o wa ni ilẹ daradara.
2. Depress the retainer clip to release the locking strap, and then remove the power cord from the external power supply system and the power module.
3. Press the extraction handle of the module with one hand, and pull the extraction handle using your other hand, until the module completely comes out of the chassis.
Caution: Unplug the power cord first, then remove the power supply module. When removing a power supply module, make sure that the power supply module is set correctly in the
operation of installation. In order to better protect the power supply module during removal, it is recommended that you
package it in an antistatic bag.
Fan Module fifi sori
S6500-24GP4XF/S6500-48GP6XF/S6500-24M4Y/S6500-24MPP4Y/S6500-48M6Y/S650048MPP6Y/S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C/S7500-48Y8C/S7500-32C is shipped with hot-swappable fan modules installed. They look like below, and the images may differ from your actual product.
olusin 2-11 Irisi ti Fan Module
LED

20 fifi sori ẹrọ

Extraction Handle Retainer Clips Release Handle

Omada Campus Stackable L3 Managed Switch For normal operation of the switch, please ensure that models with 5 fan modules maintain at least 4 operational modules, while models with 4 fan modules maintain at least 3 operational modules. If one fan module is damaged, please replace it as follows: 1. Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well
ilẹ. 2. Tẹ awọn isediwon mu ti awọn module pẹlu ọkan ọwọ, ki o si fa isediwon mu titi ti
module patapata ba jade ti awọn ẹnjini.
olusin 2-12 Yọ A bajẹ Fan Module
3. Press the extraction handle of a new fan module with one hand, and hold the bottom of the module using your other hand. Gently push the module in along the slot guide rail.
4. Release the extraction handle to fix the power supply module in place. Caution: S6500-24GP4XF/S6500-48GP6XF/S6500-24M4Y/S6500-24MPP4Y/S6500-48M6Y/S6500-48MPP6Y/ S7500-26XF6Y uses hot-swappable fan modules with a maximum speed of 9,000 RPM. S7500-48XF4C/ S7500-24Y4C/S7500-48Y8C/S7500-32C uses hot-swappable fan modules with a maximum speed of 18,000 RPM. Please do not interchange or mix fan modules between models. Sharp edges on the fan module may cause injury, so please operate with caution. Make sure the damaged fan module is in place before you are going to replace it. DO NOT unplug the damaged fan module until the replacement operation. Do not use too much force in the replacement. If resistance is encountered or positions of the fan module appear larger during installation, you must first remove the module and then reinstall the module. If the Retainer Clips cannot spring up naturally and the power module is blocked, it may be due to the fan module is not installed properly. Please check carefully.
Fifi sori 21

Omada Campus Stackable L3 Managed Switch

Chapter 3 Asopọ

3.1 àjọlò Port

So ibudo Ethernet kan ti yipada si kọnputa nipasẹ okun RJ45 bi nọmba atẹle ti fihan.

olusin 3-1

Nsopọ ibudo RJ45

Ibudo RJ45

RJ45 Okun

3.2 10G SFP+/25G SFP28/100G QSFP28 Slot

The following figure demonstrates the connection of 10G SFP+/25G SFP28/100G QSFP28 slot to an optical module

olusin 3-2

Inserting the Fiber Module

Slot Fiber Module

3.3 Console Port
CLI (Ibaraẹnisọrọ Laini Aṣẹ) ngbanilaaye lati ṣakoso iyipada, nitorinaa o le gbe CLI lẹhin sisopọ awọn PC tabi Awọn ebute si ibudo console lori ẹrọ iyipada nipasẹ okun kan (okun RJ45 ti pese, lakoko ti a ko pese okun Iru-C)
So ibudo console RJ45 ti ẹrọ naa pọ pẹlu kọnputa rẹ nipasẹ okun console bi nọmba atẹle ti fihan.

22 Asopọmọra

olusin 3-3

Nsopọ Port Console (RJ45).

Omada Campus Stackable L3 Managed Switch

So iru-C console ibudo ti awọn ẹrọ pẹlu kọmputa rẹ nipasẹ awọn Iru-C USB (ko pese) bi awọn nọmba wọnyi fihan.

olusin 3-4

Nsopọ Port Console (USB).

Note: RJ45 console port and Type-C console port cannot be used concurrently. Type-C Console port takes
priority over the RJ45 console port. The Type-C console port is hot-pluggable while the RJ45 console port is not. Keep the device power
off when plugging the console cable into the RJ45 console port. Do not connect the console port with other ports by RJ45 cable.
3.4 Ṣayẹwo Fifi sori ẹrọ
Lẹhin ipari fifi sori ẹrọ, ṣayẹwo awọn nkan wọnyi: 5 si 10 cm ti imukuro yẹ ki o wa ni ayika ẹrọ fun fentilesonu ati rii daju pe ṣiṣan afẹfẹ
jẹ deedee. Awọn voltage ti awọn ipese agbara pàdé awọn ibeere ti awọn input voltage ti ẹrọ. Soketi agbara, ẹrọ ati agbeko ti wa ni ipilẹ daradara. Ẹrọ naa ti sopọ ni deede si awọn ẹrọ nẹtiwọki miiran.
Asopọmọra 23

Omada Campus Stackable L3 Managed Switch

3.5 Agbara Lori

Pulọọgi asopo obinrin ti okun agbara ti a pese sinu iho agbara ti ẹrọ naa ki o pulọọgi asopo rere sinu iṣan agbara bi nọmba atẹle ti fihan. Rii daju wipe voltage ti awọn ipese agbara pàdé awọn ibeere ti awọn input voltage (100-240 V ~ 50/60 Hz).

olusin 3-5

Nsopọ si Ipese Agbara

Note: The figure is to illustrate the application and principle. The provided plug and module in your region
may differ from the figures above. Generally PWR1 takes priority over PWR2.

3.6 Ibẹrẹ
Lẹhin ti ẹrọ naa ti ni agbara lori, o bẹrẹ Igbeyewo Ara-Lori Agbara-Lori. Lẹsẹẹsẹ awọn idanwo ṣiṣe laifọwọyi lati rii daju pe awọn iṣẹ ẹrọ naa daradara. Ni akoko yii, awọn olufihan LED rẹ yoo dahun ni aṣẹ atẹle:
1. Awọn itanna Atọka LED PWR lori gbogbo akoko. Awọn LED SYS ati awọn afihan LED ti gbogbo awọn ibudo pa.
2. Lẹhin nipa ọkan iseju, SYS LED ati LED ifi ti gbogbo awọn ibudo yoo filasi momentarily ati ki o si pa.
3. Awọn iṣeju aaya pupọ lẹhinna, itọka LED SYS yoo tan, eyiti o duro fun ipilẹṣẹ aṣeyọri.
3.7 akopọ Topology
With stackable design, the switches can be stacked into one stack topology for higher reliability, larger bandwidth, and simpler networking. To build the stack topology, you need to prepare 2-12 switches and enough 10G SFP+/25G SFP28/100G QSFP28 modules/cables. For more details, see the table below:

Yipada

Awoṣe (awọn) ibaramu

Opoiye

S6500-24G4XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-48G6XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-24GP4XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-48GP6XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-24M4Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y S6500-24MPP4Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y

2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode)

24 Asopọmọra

Omada Campus Stackable L3 Managed Switch

S6500-48M6Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y

S6500-48MPP6Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y

S7500-26XF6Y S7500-26XF6Y

S7500-48XF4C S7500-48XF4C

S7500-24Y4C S7500-24Y4C

S7500-48Y8C S7500-48Y8C

S7500-32C

Awọn ẹya topology akopọ mẹta wa fun awọn oju iṣẹlẹ oriṣiriṣi, jọwọ kọ topology to dara ni ibamu si awọn iwulo rẹ:

1. Pq Topology: Pq topology jẹ jo o rọrun ati ki o ko beere USB asopọ laarin awọn akọkọ ati ki o kẹhin kuro. O dara fun iṣakojọpọ ijinna pipẹ, ṣugbọn igbẹkẹle rẹ jẹ kekere.

olusin 3-6

Pq Topology

Stacking Port Group 2
Stacking Port Group 1

…

2. Topology oruka: Iwọn topology ni igbẹkẹle ti o ga julọ ni akawe pẹlu topology pq. Nigbati ọkan ninu awọn ẹwọn inu topology oruka ba ti ge asopọ, topology oruka di topology pq, ṣugbọn gbogbo eto akopọ le tun ṣiṣẹ ni deede. Topology oruka nilo asopọ okun laarin ẹyọ akọkọ ati ti o kẹhin, nitorinaa ko dara fun iṣakojọpọ jijin.

olusin 3-7

Topology oruka

Stacking Port Group 2

Stacking Port Group 1

…

Asopọmọra 25

Omada Campus Stackable L3 Managed Switch

3. Star Topology: Star topology so awọn yipada si a aringbungbun yipada akọkọ, Nitorina, o le significantly mu data firanšẹ siwaju oṣuwọn laarin omo egbe yipada nigba ti pese iṣọkan isakoso.

olusin 3-8

Star Topology

Stacking Port Group 2

Stacking Port Group 3

Stacking Port Group 1

…

Note: The stacking port is not allowed to connect to non-stacking port, as it may affect the operation of the
device. Stacking ports with the same group ID are not allowed to connect to stacking ports with different
group IDs, neither to different devices. A stacking port group is a logical port dedicated to stacking and needs to be bound to a stacking port.
A stacking port group can be bound to one or more stacking ports to improve bandwidth and reliability.

26 Asopọmọra

Omada Campus Stackable L3 Managed Switch

Chapter 4 iṣeto ni

4.1 Iṣeto ni Loriview
Yipada ṣe atilẹyin awọn aṣayan iṣeto meji:
Ipo Iduroṣinṣin: Tunto ati ṣakoso iyipada ni ẹyọkan. Ipo Alakoso: Tunto ati ṣakoso awọn ẹrọ nẹtiwọọki ni aarin. O ti wa ni niyanju ninu awọn
nẹtiwọọki iwọn-nla, eyiti o ni awọn ẹrọ lọpọlọpọ gẹgẹbi awọn aaye iwọle, awọn iyipada, ati awọn ẹnu-ọna.
Akiyesi: Nigbati yipada ba yipada lati Ipo Standalone si Ipo Iṣakoso, awọn atunto ti yipada yoo sọnu. Fun awọn alaye, tọka si awọn iwe aṣẹ ti o ni ibatan lori ile -iṣẹ igbasilẹ ti oṣiṣẹ wa webojula: https://support.omadanetworks.com/product/.

4.2 Ipo imurasilẹ

Ni Ipo Iduroṣinṣin, lo kọnputa kan lati tunto ati ṣakoso iyipada nipa lilo GUI (Aṣaro wiwo olumulo ayaworan) tabi CLI (ni wiwo laini aṣẹ).

olusin 4-1

Topology fun Iduroṣinṣin Ipo

Yipada

Lilo GUI
1. Lati wọle si oju-iwe iṣakoso ti iyipada, rii daju pe iyipada ati kọnputa wa ni subnet kanna. Ṣii ẹrọ lilọ kiri ayelujara kan ki o tẹ adirẹsi IP yipada ni aaye adirẹsi, lẹhinna tẹ bọtini Tẹ.
Ti o ba ti yipada gba adiresi IP lati DHCP server (ojo melo kan ẹnu), ri awọn yipada ká IP adirẹsi lori DHCP server.
Ti kii ba ṣe bẹ, lo adiresi IP aiyipada 192.168.0.1 lati ṣe ifilọlẹ oju -iwe iṣakoso oluyipada naa.

2. Ni igba akọkọ ti o wọle, ṣeto orukọ olumulo ati ọrọigbaniwọle lati daabobo nẹtiwọki rẹ ati awọn ẹrọ daradara. Lẹhin iyẹn, eto naa yoo ṣe atunṣe ọ laifọwọyi pada si wiwo iwọle lati jẹrisi pẹlu awọn iwe-ẹri tuntun ti a ṣẹda.

3. Lẹhin iwọle ti aṣeyọri, oju-iwe akọkọ yoo han. O le tẹ awọn akojọ aṣayan ni apa oke ati apa osi lati tunto awọn iṣẹ to baamu.
Fun awọn atunto alaye, tọka si Itọsọna olumulo ati Itọsọna CLI. Awọn itọsọna le ṣee ri lori aarin igbasilẹ ti oṣiṣẹ wa webojula: https://support.omadanetworks.com/product/.
Lilo CLI Ṣeto Telnet tabi asopọ SSH lati wọle si iyipada nipasẹ CLI.

Iṣeto ni 27

Omada Campus Stackable L3 Managed Switch

Lo ibudo console lati wọle si iyipada. Nigbati o ba nlo ibudo console, bẹrẹ eto imupese ebute (bii Hyper Terminal) lori PC ki o tunto eto imupese ebute bi atẹle:

Baud Oṣuwọn 38400 bps

Data Bits 8

Parity Kò

Duro Bits 1

Iṣakoso Sisan Ko si

Fun awọn atunto alaye, tọka si Itọsọna olumulo ati Itọsọna CLI. Awọn itọsọna le ṣee ri lori aarin igbasilẹ ti oṣiṣẹ wa webojula: https://support.omadanetworks.com/product/.
Note: You may need to change the password the first time you log in, which will better protect your network and devices.

4.3 Adarí Ipo
Controller Mode applies to the large scale network with mass devices. All devices can be centrally configured and monitored via Omada Pro Hardware Controller (C5300), Omada Pro Software Controller, or Omada Pro Cloud-Based Controller.
Note: Before the following configurations, make sure the switch can access the internet. When using Omada Pro Hardware/Software/Cloud-based Controller, make sure the switch and the controller are in the same subnet. Typically, the switch obtains IP address from the DHCP server. You can check the switch’s IP address on the DHCP server.

Via Omada Pro Hardware Controller (C5300)

Omada Pro Hardware Controller (C5300) is a good alternative if you have no spare PC to keep running Omada Pro Software Controller in the network. It needs to be purchased additionally. Follow the steps below to configure the Omada Pro Hardware Controller (C5300).

olusin 4-2

Manage the network via Omada Pro Hardware Controller (C5300)

Gateway Yipada

Omada Pro Hardware Controller (C5300) EAP
28 iṣeto ni

EAP

Awọn onibara

Omada Campus Stackable L3 Managed Switch

Note: Before you start, be sure to power up and connect your devices according to the topology figure. A DHCP server (typically a gateway with DHCP function enabled) is required to assign IP addresses to
the EAPs and clients in your local network. Omada Pro Controller must have network access to some Omada campus devices (the gateway,
switch, or APs) in order to find, adopt, and manage them.

1. Wa adiresi IP ti ẹnu-ọna. Ṣii laini aṣẹ lori PC rẹ ki o tẹ ipconfig sii. Ninu atokọ abajade, wa Ẹnu-ọna Aiyipada, eyiti o tun jẹ adiresi IP ti ẹnu-ọna.
2. Lọlẹ a web kiri ati ki o tẹ awọn IP adirẹsi ti ẹnu-ọna. Wọle si ẹnu-ọna ẹnu-ọna web oju-iwe. Lẹhinna lọ si Nẹtiwọọki> LAN> Akojọ Onibara DHCP lati wa adiresi IP ti oludari rẹ gẹgẹbi adirẹsi MAC rẹ.
3. Tẹ awọn IP adirẹsi ti awọn rẹ oludari ni awọn adirẹsi igi lati si awọn oniwe- web oju-iwe.
4. Lori Omada Pro Adarí web oju-iwe, tẹle oluṣeto lati pari iṣeto ni kiakia.
5. Lẹhin iṣeto ni kiakia, oju-iwe iwọle yoo han. Tẹ orukọ olumulo ati ọrọ igbaniwọle ti o ṣẹda ki o tẹ Wọle lẹhinna o le tunto oludari naa siwaju.
6. Ti o ba fẹ ṣakoso awọn ẹrọ latọna jijin, tẹle awọn igbesẹ atẹle:
a. Rii daju pe Wiwọle awọsanma ṣiṣẹ lori oludari rẹ. Nipa aiyipada, Wiwọle awọsanma ti ṣiṣẹ. Rii daju pe LED awọsanma n tan imọlẹ laiyara.

b. Lọlẹ a web ẹrọ aṣawakiri ati tẹ https://omada.tplinkcloud.com sinu ọpa adirẹsi. Tẹ ID TP-Link rẹ ati ọrọ igbaniwọle sii lati wọle. Tẹ + Fi Adarí ko si yan Adarí Hardware lati ṣafikun oludari rẹ. Lẹhinna o le tunto oludari siwaju sii.

For more details, refer to the Installation Guide of C5300.

Nipasẹ Omada Pro Software Adarí

Download the Omada Pro Software Controller on a PC with Windows OS or Linux OS. Then run the file and follow the wizard to install the Omada Pro Software Controller. Follow the steps below to configure the Controller.

olusin 4-3

Ṣakoso nẹtiwọki nipasẹ Omada Pro Software Adarí

Ẹnu-ọna

Yipada

Adarí

Omada Pro Software Adarí AP

nṣiṣẹ lori Gbalejo PC

Awọn onibara

Iṣeto ni 29

Omada Campus Stackable L3 Managed Switch

1. Launch the Omada Pro Software Controller on your PC. After the initiation process, the controller automatically opens its web oju-iwe. Ti kii ba ṣe bẹ, tẹ Lọlẹ ẹrọ aṣawakiri kan lati Ṣakoso Nẹtiwọọki naa.
2. Lori Omada Pro Adarí web oju-iwe, tẹle oluṣeto lati pari iṣeto ni kiakia.
3. Lẹhin iṣeto ni kiakia, oju-iwe iwọle yoo han. Tẹ orukọ olumulo ati ọrọ igbaniwọle ti o ṣẹda ki o tẹ Wọle lẹhinna o le tunto oludari naa siwaju.
4. Ti o ba fẹ ṣakoso awọn ẹrọ latọna jijin, tẹle awọn igbesẹ atẹle:
a. Make sure that Cloud Access is enabled on your controller and your controller has been bound with your TP-Link ID. On the Omada Pro Controller’s web oju-iwe, lọ si Eto> Wiwọle Awọsanma lati mu Wiwọle Awọsanma ṣiṣẹ ati di ID TP-Link rẹ. Ti o ba ti ṣeto rẹ ni iṣeto ni iyara, fo igbesẹ yii.
b. Lọlẹ a web ẹrọ aṣawakiri ati tẹ https://omada.tplinkcloud.com sinu ọpa adirẹsi. Tẹ ID TP-Link rẹ ati ọrọ igbaniwọle sii lati wọle. Atokọ awọn oludari ti a ti dè pẹlu ID TP-Link rẹ yoo han. Lẹhinna o le tẹ ifilọlẹ lati tunto oludari siwaju sii.

Note: To manage your devices, Omada Pro Software Controller needs to keep running on your computer.

Nipasẹ Omada Pro Awọsanma-orisun Adarí

Omada Pro Awọsanma-orisun Adarí jẹ yiyan ti o dara laisi iwulo lati fi sori ẹrọ oludari sọfitiwia lori PC kan.

Awọn iwe-aṣẹ nilo lati ra ni afikun.

olusin 4-4

Ṣakoso nẹtiwọọki nipasẹ Omada Pro Awọsanma-orisun Adarí

Omada awọsanma

Ẹnu-ọna

Yipada

Awọn onibara
1. Contact the sales staff to grant the Omada Pro Cloud-Based Controller permission. 2. Launch a web ẹrọ aṣawakiri ati tẹ https://omada.tplinkcloud.com sinu ọpa adirẹsi. Wọle pẹlu
your TP-Link ID.
30 iṣeto ni

Omada Campus Stackable L3 Managed Switch 3. Click + Add Controller and choose Cloud-Based Controller to add an Omada Pro Controller. Then
o le ṣe ifilọlẹ oludari lati gba ati ṣakoso awọn ẹrọ. * Ohun elo Omada Pẹlu ohun elo Omada, o tun le ṣakoso oludari rẹ ni aaye agbegbe tabi aaye jijin nipasẹ ẹrọ alagbeka rẹ. Fun awọn atunto alaye, tọka si Itọsọna olumulo ti oludari. Itọsọna naa le wa lori aaye igbasilẹ ti osise wa webojula: https://support.omadanetworks.com/product/.
Iṣeto ni 31

Omada Campus Stackable L3 Managed Switch
Afikun A Laasigbotitusita
Q1. Kini MO le ṣe ti Mo gbagbe orukọ olumulo ati ọrọ igbaniwọle ti iyipada naa?
1. So console ibudo ti awọn PC si awọn console ibudo ti awọn yipada ki o si ṣi a ebute emulation eto.
2. Pa agbara ki o tun yipada. Ṣe iṣe ti itọkasi nipasẹ eto imupese ebute lati de akojọ aṣayan bootUtil. Iṣe naa yatọ lati ọja si ọja. Awọn iṣe to ṣee ṣe akojọ si isalẹ: · Tẹ bọtini eyikeyi lati da autoboot duro. Tẹ CTRL-B lati de akojọ aṣayan bootUtil.
3. Awọn akojọ aṣayan bootUtil yoo han. Tẹ nọmba 6 sii lati yan aṣayan “imupadabọ Ọrọigbaniwọle” ki o tẹ Y lati pa gbogbo awọn olumulo ati awọn ọrọ igbaniwọle rẹ. Lẹhinna o le tun orukọ olumulo ati ọrọ igbaniwọle pada.
Q2. Kini idi ti PWR LED ṣiṣẹ aiṣedeede? PWR / Power LED yẹ ki o tan soke nigbati eto agbara ṣiṣẹ deede. Ti PWR/Power LED ba ṣiṣẹ laiṣe deede, ṣe awọn igbesẹ wọnyi:
1. Rii daju wipe okun agbara ti wa ni ti sopọ daradara, ati awọn olubasọrọ agbara jẹ deede. 2. Rii daju pe voltage ti awọn ipese agbara pàdé awọn ibeere ti awọn input voltage ti awọn
yipada.
Q3. Kini MO le ṣe ti Emi ko ba le wọle si web oju-iwe iṣakoso? Gbiyanju awọn wọnyi:
1. Ṣayẹwo gbogbo LED ibudo lori iyipada ati rii daju pe okun Ethernet ti sopọ daradara. 2. Gbiyanju ibudo miiran lori iyipada ati rii daju pe okun Ethernet dara ati pe o ṣiṣẹ deede. 3. Fi agbara pa a yipada ati, lẹhin igba diẹ, fi agbara mu lẹẹkansi. 4. Rii daju pe adiresi IP ti PC rẹ ti ṣeto laarin subnet ti yipada. 5. Ti o ko ba le wọle si oju-iwe iṣeto, tun yipada si awọn aṣiṣe ile-iṣẹ rẹ. Lẹhinna
adiresi IP ti PC rẹ yẹ ki o ṣeto bi 192.168.0.x ("x" jẹ nọmba eyikeyi lati 2 si 254) ati iboju-boju subnet bi 255.255.255.0.
Q4. Kini idi ti eto imupese ebute ko han ni deede? Gbiyanju awọn wọnyi:
1. Rii daju pe ipese agbara jẹ deede ati okun console ti sopọ mọ daradara. 2. Ṣayẹwo ti o ba ti console USB ni ọtun iru. 3. Rii daju pe awọn paramita ti eto emulation ebute jẹ deede: tunto Bits fun iṣẹju-aaya
bi 38400, Data die-die bi 8, Parity bi Kò, Duro die-die bi 1, ati Sisan Iṣakoso bi Kò.
32 Àfikún A Laasigbotitusita

Omada Campus Stackable L3 Managed Switch

Àfikún B ni pato

Specifications for S6500 Series Switches

Nkan

Akoonu

IEEE 802.3, IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3ae, IEEE 802.3x

Awọn ajohunše

IEEE 802.3af/at (For S6500-24GP4XF, S6500-48GP6XF) IEEE 802.3af/at/bt (For S6500-24MPP4Y, S6500-48MPP6Y)

IEEE 802.3bz, IEEE 802.3by, IEEE 802.3cc (For S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y)

10BASE-T: 2-pair UTP/STP of Cat. 3,4,5 (maximum 100 m) 100BASE-TX: 2-pair UTP/STP of Cat. 5 or above (maximum 100 m) 1000BASE-T: 4-pair UTP/STP of Cat. 5e or above (maximum 100 m) 2.5GBASE-T: 4-pair UTP/STP of Cat. 5e or above (maximum 100 m) Transmission Medium 1000BASE-SX/LX/LX10/BX10: MMF, SMF 10GBASE-SR/LR: MMF, SMF 10G SFP+ Direct Attach Cable (SM5220-1M, SM5220-3M) 25GBASE-SR/LR: MMF, SMF (SM6110-SR, SM6110-LR) 25G SFP28 Direct Attach Cable (SM6220-1M)

S6500-24G4XF/S6500-24M4Y: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, Port 1-24, Port 25-28 S6500-24GP4XF/S6500-24MPP4Y: PWR1, PWR2, SYS, FAN, PoE Max, MGMT, MST, SPEED, STK, PoE, Port 1-24, Port 25-28 LED S6500-48G6XF/S6500-48M6Y: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, Port 1-48, Port 49-54 S6500-48GP6XF/S6500-48MPP6Y: PWR1, PWR2, SYS, FAN, PoE Max, MGMT, MST, SPEED, STK, PoE, Port 1-48, Port 49-54

Àfikún B Awọn pato 33

Omada Campus Stackable L3 Managed Switch

PoE Isuna

For S6500-24GP4XF: 402W (with 1*PSM500-AC, by default) 720W (with 1*PSM900-AC) 720W (with 2*PSM500-AC) 720W (with 1*PSM500-AC and 1*PSM900-AC) 720W (with 2*PSM900-AC) For S6500-48GP6XF: 764W (with 1*PSM900-AC, by default) 384W (with 1*PSM500-AC) 812W (with 2*PSM500-AC) 1176W (with 1*PSM500-AC and 1*PSM900-AC) 1440W (with 2*PSM900-AC) For S6500-24MPP4Y: 751W (with 1*PSM900-AC, by default) 378W (with 1*PSM500-AC) 802W (with 2*PSM500-AC) 1168W (with 1*PSM500-AC and 1*PSM900-AC) 1534W (with 2*PSM900-AC) For S6500-48MPP6Y: 701W (with 1*PSM900-AC, by default) 328W (with 1*PSM500-AC) 752W (with 2*PSM500-AC) 1118W (with 1*PSM500-AC and 1*PSM900-AC) 1484W (with 2*PSM900-AC)

Awọn iwọn otutu ti nṣiṣẹ & Giga

For S6500-24G4XF/S6500-48G6XF/S6500-24M4Y/S6500-48M6Y: -5 °C to 50 °C (23 °F to 122 °F) @ 300 meters -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters For S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y: -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters

Ibi ipamọ otutu -40 °C si 70 °C (-40 °F si 158 °F)

Ọriniinitutu ti nṣiṣẹ 10% si 90% RH Ti kii-condensing

Ọriniinitutu ipamọ

5% to 90% RH ti kii-condensing

34 Àfikún B ni pato

Omada Campus Stackable L3 Managed Switch

Specifications for S7500 Series Switches

Nkan

Akoonu

Awọn ajohunše

IEEE 802.3, IEEE 802.3x IEEE 802.3z, IEEE 802.3ae (For S7500-26XF6Y, S7500-48XF4C, S7500-24Y4C, S7500-48Y8C IEEE 802.3by, IEEE 802.3cc (For S7500-26XF6Y, S7500-24Y4C, S7500-48Y8C) IEEE 802.3 ba, IEEE 802.3bm (For S7500-48XF4C , S7500-24Y4C, S7500-48Y8C, S7500-32C)

1000BASE-SX/LX/LX10/BX10: MMF, SMF 10GBASE-SR/LR: MMF, SMF 10G SFP+ Direct Attach Cable (SM5220-1M, SM5220-3M) 25GBASE-SR/LR: MMF, SMF (SM6110-SR, SM6110-LR) 25G SFP28 Direct Attach Cable (SM6220-1M) 40GBASE-SR4/LR4: MMF, SMF (For S7500-48XF4C, S7500-24Y4C, Transmission Medium S7500-48Y8C, S7500-32C) 40G QSFP+ Direct Attach Cable (For S7500-48XF4C, S7500-24Y4C, S7500-48Y8C, S7500-32C) 100GBASE-SR4/LR4: MMF, SMF (SM9110-SR4 for S7500-48XF4C, S7500-24Y4C, S7500-48Y8C, S7500-32C) 100G QSFP28 Direct Attach Cable (SM9220-1M for S7500-48XF4C, S7500-24Y4C, S7500-48Y8C, S7500-32C)

LED
Awọn iwọn otutu ti nṣiṣẹ & Giga

S7500-26XF6Y: PWR1, PWR2, SYS, FAN, MGMT, MST, SPD, STK, SFP+, SFP28 S7500-48XF4C: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, SFP+, QSFP28 S7500-24Y4C: PWR1, PWR2, SYS, FAN, MGMT, MST, SPD, STK, SFP28, QSFP28 S7500-48Y8C: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, SFP28, QSFP28 S7500-32C: PWR1, PWR2, SYS, MGMT, FAN, MST, SPEED, STK, QSFP28 -5 °C to 45 °C (23 °F to 113 °F) @ 300 meters -5 °C to 40 °C (23 °F to 104 °F) @ 2,000 meters -5 °C to 35 °C (23 °F to 95 °F) @ 3,000 meters

Ibi ipamọ otutu -40 °C si 70 °C (-40 °F si 158 °F)

Ọriniinitutu ti nṣiṣẹ 10% si 90% RH Ti kii-condensing

Ọriniinitutu ipamọ

5% to 90% RH ti kii-condensing

For S7500-26XF6Y, S7500-48XF4C, and S7500-24Y4C, the maximum operating temperature supported can reach 50 °C (122 °F) @ 300 meters, 45 °C (113 °F) @ 2,000 meters, and 40 °C (104 °F) @ 3,000 meters.
Giga atilẹyin jẹ ipele okun si 5000 m. O yẹ ki o ṣe akiyesi pe nigbati giga ba ga ju 2000 m, fun gbogbo awọn mita 220 ti ilosoke giga, iwọn otutu ti o pọ julọ yoo lọ silẹ nipasẹ 1°C (1.8°F).

Àfikún B Awọn pato 35

Omada Campus Stackable L3 Managed Switch

Awọn pato fun Awọn modulu Ipese Agbara

PSM500-AC
(For S6500-24GP4XF/ S6500-48GP6XF/ S6500-24MPP4Y/ S6500-48MPP6Y)

PSM900-AC
(For S6500-24GP4XF/ S6500-48GP6XF/ S6500-24MPP4Y/ S6500-48MPP6Y)

PSM550-AC
(For S6500-24M4Y/ S6500-48M6Y/ S7500-26XF6Y/ S7500-48XF4C/ S7500-24Y4C/ S7500-48Y8C/ S7500-32C)

Agbara Input

100 V240 V~ 50/60 Hz 8A

100-120V (included)~ 50/60Hz 12A (for locations using low voltage, see specifications for specific countries/ regions)
120 (not included)240V~ 50/60Hz 10A (for other locations)

100 V240 V~ 50/60 Hz 7A

O wujade Voltage

Primary: 53.5 VDC Standby: 12 VDC

Primary: 12 VDC Standby: 12 VDC

Ijade lọwọlọwọ

9.35 A (O pọju)

16.5 A (O pọju)

45 A (O pọju)

Agbara Ijade

500 W (O pọju)

900 W (O pọju)

550 W (O pọju)

Giga iṣẹ

For PSM500-AC/PSM900-AC: Sea level to 3000 m For PSM550-AC: Sea level to 5000 m

36 Àfikún B ni pato

CE Mark Ikilọ
Eyi jẹ ọja kilasi A. Ni agbegbe ile, ọja yi le fa kikọlu redio, ninu ọran ti olumulo le nilo lati ṣe awọn igbese to peye.
EU Declaration of ibamu
TP-Link ni bayi n kede pe iyipada wa ni ibamu pẹlu awọn ibeere pataki ati awọn ipese miiran ti o yẹ ti awọn itọsọna 2014/30/EU, 2014/35/EU, 2011/65/EU ati (EU) 2015/863. Ikede EU atilẹba ti Ibamu ni a le rii ni https://www.tp-link.com/en/support/ce/
UK Declaration of ibamu
TP-Link ni bayi n kede pe iyipada naa wa ni ibamu pẹlu awọn ibeere pataki ati awọn ipese miiran ti o yẹ ti Awọn ilana Ibamu Itanna 2016 ati Awọn ilana Awọn ohun elo Itanna (Aabo) 2016. Ikede UK atilẹba ti Ibamu le ṣee rii ni https://www.tp-link.com/support/ukca/
, .
IKIRA:
Ọpa meji, didoju didoju. Ge asopọ akọkọ ṣaaju ṣiṣe.
Alaye Aabo
Jeki ẹrọ naa kuro ni omi, ina, ọriniinitutu tabi agbegbe gbona. Ma ṣe gbiyanju lati ṣajọpọ, tunše, tabi tun ẹrọ naa pada.Ti o ba nilo iṣẹ, jọwọ kan si wa. · Gbe awọn ẹrọ pẹlu awọn oniwe-isalẹ dada sisale. · Awọn plug lori okun ipese agbara ti wa ni lo bi awọn ẹrọ ge asopọ, awọn iho-iṣan yoo jẹ
awọn iṣọrọ wiwọle. · Pulọọgi ọja sinu awọn iṣan odi pẹlu asopọ ilẹ nipasẹ okun ipese agbara
or plug. · The socket-outlet shall be installed near the equipment and shall be easily accessible. · The PoE ports shall not be used to charge lithium batteries or devices supplied by lithium
awọn batiri.

· Operating temperature: For S6500-24G4XF/S6500-48G6XF/S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/ S7500-48XF4C/S7500-24Y4C: -5 °C to 50 °C (23 °F to 122 °F) @ 300 meters -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters For S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y: -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters S7500-48Y8C/S7500-32C: -5 °C to 45 °C (23 °F to 113 °F) @ 300 meters -5 °C to 40 °C (23 °F to 104 °F) @ 2,000 meters -5 °C to 35 °C (23 °F to 95 °F) @ 3,000 meters
· : S6500-24G4XF/S6500-48G6XF/S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/S7500-48XF4C/ S7500-24Y4C -5°C 50°C23°F 122°F@ 300 -5°C 45°C23°F 113°F@ 2,000 -5°C 40°C23°F 104°F@ 3,000 S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y -5°C 45°C23°F 113°F@ 2,000 -5°C 40°C23°F 104°F@ 3,000 S7500-48Y8C/S7500-32C -5°C 45°C23°F 113°F@ 300 -5°C 40°C23°F 104°F@ 2,000 -5°C 35°C23°F 95°F@ 3,000
This equipment is not suitable for use in locations
where children are likely to be present.

Jọwọ ka ati tẹle alaye aabo loke nigbati o nṣiṣẹ ẹrọ naa. A ko le ṣe iṣeduro pe ko si ijamba tabi ibajẹ ti yoo waye nitori lilo aibojumu ẹrọ naa. Jọwọ lo ọja yii pẹlu abojuto ki o ṣiṣẹ ni ewu tirẹ.

Fun atilẹyin imọ-ẹrọ, awọn itọsọna olumulo ati alaye miiran, jọwọ ṣabẹwo https://support.omadanetworks.com/, tabi nirọrun ṣe ọlọjẹ koodu QR naa.
© 2026 TP-Ọna asopọ 7100002759 REV2.0.1

Awọn iwe aṣẹ / Awọn orisun

Omada L3 Campus Stackable Managed Switch [pdf] Afowoyi olumulo
L3Campus Stackable Managed Switch, L3, Campus Stackable Managed Switch, Stackable Managed Switch, Managed Switch, Switch

Awọn itọkasi

Itọsọna olumulo

L3Campus Stackable Managed Switch

Awọn pato

Awọn ilana Lilo ọja

Chapter 2: fifi sori

Abala 3: Asopọ

Chapter 4: iṣeto ni

FAQ

Q: What should I do if the LED indications show an error?

Awọn iwe aṣẹ / Awọn orisun

Awọn itọkasi

Fi ọrọìwòye

Fagilee esi