XP-8v
Advanced Control Processor
Itọsọna itọkasi
XP-8v Advanced Control Processor
The XP-8v is a high-end remote control processor for automating the operation of electronic systems in homes and office buildings. The combination of a blazing fast MPU, real-time/multitasking operating system, and tremendous expansion capability, make the XP-8v the perfect solution for large-scale and complex projects.
The XP-8v provides superior quality and reliability as well as these features:
- Powerful 1GHz internal processor.
- 1GB of RAM memory and 512MB of non-volatile flash memory built in.
- SD/MM card slot allows memory expansion.
- Eight multi-purpose I/O ports.
- Eight programmable relay outputs.
- Eight two-way RS-232 ports.
- Eight sense inputs.
- Multi-purpose I/O ports are compatible with industry-standard IR emitters, blasters and repeater systems.
- Multi-purpose I/O ports support all optional RTI power sensing and communications modules.
- All output ports incorporate both short-circuit and overload protection.
- Ayipada IR o wu lori gbogbo awọn ibudo.
- Front panel controls/display (11 Buttons for front panel control).
- Non-volatile Flash memory stores your system configuration even when power is not present.
- Field upgradeable firmware.
- USB and Ethernet programming.
- Compatible with RTI 433MHz and 2.4GHz Zigbee RF modules.
- Astronomical clock built in for time-based event programming.
- Designed for rack mount or free standing installations.
Fifi sori & isẹ
PROGRAMMING THE XP-8v
The XP-8v must be programmed to operate. All programming is done using RTI’s Integration Designer software and is downloaded using the USB ® Programming Port located on front of XP-8v or via Ethernet.
FIRMWARE NIPA
O ṣe iṣeduro gaan pe eyi ati gbogbo awọn ọja RTI ni famuwia tuntun ti fi sori ẹrọ. Famuwia naa le rii ni apakan Oluṣowo ti RTI webAaye (www.rticontrol.com). Install the firmware using the USB Programming Port located on the front of XP-8v.
MPIO PORTS – Control via Infrared, Sensing and RS-232 (One-way)
INFRARED EMITTERS
The multi-purpose I/O ports on the XP-8v are compatible with industry standard infrared emitters and infrared repeating systems. Each output port is capable of driving up to four infrared emitters directly. The use of more than four infrared emitters requires the addition of an amplified connecting block. A connecting block can be wired up to 1000 feet away from the XP-8v using #22 AWG (minimum) wire.
INFRARED OUTPUT GAIN ADJUSTMENT
The IR output gain can be separately adjusted for each of the eight output ports. The XP-8v is shipped with the IR gain set to the optimum level for most equipment, and it should only need to be adjusted if the attached equipment is not responding reliably. If adjustment is needed, rotate the IR output controls on the front of the XP-8v clockwise for higher output power, or counter-clockwise for lower output power.
AKIYESI: The IR output feedback LEDs located on the front of the XP-8v will illuminate when any IR code is delivered out of a port. This includes IR codes “passing through” from another source, such as an IR receiver.
VPS-1 SENSOR MODULE
The multi-purpose I/O ports on the XP-8v are compatible with RTI power sensing modules (e.g. VPS-1). Follow the guide included with the modules for installation instructions, and follow the instructions in the Integration Designers software for programming details.
RS-232 COMMUNICATION MODULES (CM-232)
The multi-purpose I/O ports on the XP-8v are compatible with RTI RS-232 communication modules (e.g. CM-232). Follow the guide included with the modules for installation instructions, and follow the instructions in the Integration Designer software for programming details.
RS-232 ibudo
The XP-8v is capable of two-way control using RS-232 communication via eight RJ-45 output ports using standard Cat-5/6 cable with RJ-45 termination (568B). The XP-8v ships with eight RJ-45 (female) to DB-9 (male) adapters.
IMPORTANT NOTE: RS-232 communication cabling should be limited to 50 feet (16m) depending on baud rate.
DB-9-RJ45 ADAPTOR PINOUT
RJ-45 (XP-8v RS-232 Output)
| Pin | Orukọ ifihan agbara | Apejuwe ifihan agbara |
| 1 | DSR | Data Ṣetan |
| 2 | DCD | Awari ti ngbe |
| 3 | DTR | Data ebute Ṣetan |
| 4 | GND | Signal Ground/Common |
| 5 | RXD | Gba Data |
| 6 | TXD | Gbigbe Data |
| 7 | CTS | Ko o Lati Firanṣẹ |
| 8 | RTS | Ibere Lati Firanṣẹ |
DB-9
| Pin | Orukọ ifihan agbara | Apejuwe ifihan agbara |
| 1 | DCD | Awari ti ngbe |
| 2 | RXD | Gba Data |
| 3 | TXD | Gbigbe Data |
| 4 | DTR | Data ebute Ṣetan |
| 5 | GND | Ilẹ ifihan agbara |
| 6 | DSR | Data Ṣetan |
| 7 | RTS | Ibere Lati Firanṣẹ |
| 8 | CTS | Ko o Lati Firanṣẹ |
| 9 | NC | Ko Sopọ |
SENSE INPUTS / RELAY-TRIGGER OUTPUTS
Sense inputs and relay-trigger modes are configured within Integration Designer ® .
SENSE INPUT
Upon sensing contact closure or a voltage (2-24VDC), events can be automatically triggered such as a macro or command.
Sense contact closure: Connect conductors from the source device to each side of a sense input (A and B).
Ayé voltage okunfa: Connect positive lead from voltage source to Side A of sense input and ground lead to Side B.
RELAYS/TRIGGER OUTPUTS
Relays may be configured as a dry contact closure or a voltage trigger output (12VDC @100mA). All relays are Normally Open when not energized, and may be programmed to behave Normally Closed (as long as power is applied to the XP-8v).
Kan si bíbo: Connect the A and B contact terminals of a relay to the device.
Voltage trigger: Connect contact A to the positive lead and connect Contact B to the ground lead of the device.
O wa Labẹ Iṣakoso ®
SIGNAL IN/HIGH OUT/POWER TERMINALS
TERMINAL: +12VDC
Positive power supply connection. It is internally tied to the Power jack. This can be used to power external IR or RF receivers.
TERMINAL: GROUND
Common ground connection. Use this ground reference for any device that is connected to the +12VDC, SIGNAL IN, OR HIGH OUT terminals.
TERMINAL: INPUT
Input connection for system trigger codes. This should be connected to an RTI RM433 RF receiver
or industry standard IR repeater system. The signal voltage can be from 3VDC – 12VDC.
TERMINAL: HIGH OUT
High current (200mA) IR output connection. This can be used to power up to 10 infrared mini-emitters, an IR blaster, or extending IR control over a long distance (1000 ft. max).
ETHERNET, USB, RTI COM, EXPANSION PORT
IYAWO
This RJ-45 port allows connection to a 10/100 Base-T Ethernet network (LAN).
Network settings such as the IP address are configurable within Integration Designer®.
Ethernet may also be used to download system files to the XP-8v.
USB PORTS (REAR)
These host ports for external devices are intended for future use.
RTI COM
This RJ-45 port allows connection to a ZM-24 Zigbee transceiver module for two-way communication with compatible RTI handheld controllers. Refer to the ZM-24 Zigbee transceiver module operation guide for installation instructions.
IGBAGBO PORT
This RJ-45 port provides a convenient connection for receiving IR signals and two-way RS-485 communication from RTI in-wall controls through a CB-8 connecting block. NOTE: In-wall controllers may be connected directly to the XP-8v Expansion Port, however, they should be powered with a separate power supply.
AGBARA
IBI TI INA ELEKITIRIKI TI NWA
To power the XP-8v, use the supplied 12VDC/1Amp ibi ti ina elekitiriki ti nwa.
XP-8v Front
ÀWỌN ỌJỌRỌ AṢỌRỌ
The display on the XP-8v is designed to give the installer feedback on the current status of the XP-8v, change settings such as the time/date and offer some basic diagnostic tools for troubleshooting. See XP-8v Display Technical Bulletin for detailed display menu options.
AKIYESI
Any configuration changes made through the XP-8v display settings will be overwritten after the XP-8v is rebooted or an RTI system file is downloaded into the XP-8v memory.
FRONT PANEL LOCKOUT
It is possible to set a passcode that will block access to the menu system on the XP-8v. This can be set in the properties of the XP-8v within the RTI Integration Designer® programming software and downloaded as part of the system file. Use the cursor buttons on the XP-8v to enter the correct passcode to open the menu display.
Igbesoke
The XP-8v ships with four removable feet that allow the unit to be placed on a flat surface. The XP-8v can also be mounted in a component rack as part of a comprehensive control system. Remove feet before mounting in a rack.
Ọja Awọn akoonu
- One (1) XP-8v Advanced Control Processor
- One (1) Power supply (12V, 1A)
- Eight (8) RJ45 to DB9 serial adaptors
- Two (2) Rack ears (2) with screws (8)
- Three (3) Terminal blocks (2 x 16-position, 1 x 4-position)
- One (1) Reference guide
- One (1) MAC address card
Awọn imọran Aabo
Read and Follow Instructions. Read all safety and operating instructions before operating the unit.
Retain Instructions. Keep the safety and operating instructions for future reference.
Heed Warnings. Adhere to all warnings on the unit and in the operating instructions.
Heat. Keep the unit away from heat sources such as radiators, heat registers, stoves, etc., including amplifiers ti o gbe awọn ooru.
Power Sources. Connect the unit only to a power supply of the type described in the operating instructions, or as marked on the unit.
Power Cord Protection. Route power supply cords so that they are not likely to be walked on or pinched by items placed on or against them, paying particular attention to the cord plugs at power receptacles and at the point at which they exit from the unit.
Water and Moisture. Do not use the unit near water—for example, nitosi ibi iwẹ, ni ipilẹ ile tutu, nitosi adagun odo, nitosi ferese ṣiṣi, ati bẹbẹ lọ.
Object and Liquid Entry. Do not allow objects to fall or liquids to be spilled into the enclosure through openings.
Servicing. Do not attempt any service beyond that described in the operating instructions. Refer all other service needs to qualified service personnel.
Damage Requiring Service. The unit should be serviced by qualified service personnel when:
- Okun ipese agbara tabi plug ti bajẹ.
- Awọn nkan ti ṣubu tabi omi ti ta sinu ẹrọ naa.
- Awọn kuro ti a ti fara si ojo.
- Kuro ko han lati ṣiṣẹ ni deede tabi ṣafihan iyipada ti o samisi ninu iṣẹ.
- Ẹka naa ti lọ silẹ tabi ibi-ipamọ ti bajẹ.
Ninu
To clean your XP8v, lightly dampyo aṣọ ti ko ni lint pẹlu omi itele tabi ohun ọṣẹ kekere kan ki o nu awọn aaye ita.
AKIYESI: Maṣe lo awọn kẹmika lile nitori ibajẹ si ẹyọkan le ṣẹlẹ.
Federal Communications Commission akiyesi
Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni-nọmba Kilasi B kan, ni ibamu si Apá 15 ti Awọn ofin FCC. Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to tọ si kikọlu ipalara ni fifi sori ibugbe kan. Eyikeyi iyipada tabi awọn iyipada ti ko fọwọsi ni pato nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ẹrọ naa.
Ẹrọ yii n ṣe ipilẹṣẹ, nlo, ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato.
Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:
- Reorient tabi tun eriali gbigba pada.
- Mu iyatọ pọ si laarin ẹrọ ati olugba.
- So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ.
- Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.
Ẹrọ yii ni ibamu pẹlu Apá 15 ti Awọn ofin FCC. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:
- Ẹrọ yii le ma fa kikọlu ipalara.
- Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba pẹlu kikọlu ti o le fa iṣẹ ti ko fẹ.
Industry Canada ibamu Gbólóhùn
Ẹrọ yii ni ibamu pẹlu iwe-aṣẹ ile-iṣẹ Canada-alayokuro(awọn) RSS. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:
- Ẹrọ yii le ma fa kikọlu ipalara.
- Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba pẹlu kikọlu ti o le fa iṣẹ ti ko fẹ.
Olubasọrọ RTI
Fun awọn iroyin nipa awọn imudojuiwọn titun, alaye ọja titun, ati awọn ẹya ẹrọ titun, jọwọ ṣabẹwo si wa web ojula ni: www.rticontrol.com
Fun alaye gbogbogbo, o le kan si RTI ni:
Latọna Imọ Incorporated
5775 12th Ave. E Suite 180
Shakopee, MN 55379
Tẹli. 952-253-3100
info@rticontrol.com
Iṣẹ & Atilẹyin
Ti o ba ni awọn iṣoro eyikeyi tabi ni ibeere kan nipa ọja RTI rẹ, jọwọ kan si Atilẹyin Imọ-ẹrọ RTI fun iranlọwọ (wo Abala Kan RTI ti itọsọna yii fun awọn alaye olubasọrọ).
RTI n pese atilẹyin imọ-ẹrọ nipasẹ tẹlifoonu tabi imeeli. Fun iṣẹ ti o ga julọ, jọwọ pese alaye atẹle:
- Orukọ rẹ
- Orukọ Ile-iṣẹ
- Nọmba foonu
- Adirẹsi imeeli
- Awoṣe ọja ati nọmba ni tẹlentẹle (ti o ba wulo)
Ti o ba ni iṣoro pẹlu ohun elo, jọwọ ṣe akiyesi ohun elo inu ẹrọ rẹ, apejuwe iṣoro naa, ati eyikeyi laasigbotitusita ti o ti gbiyanju tẹlẹ.
* Jọwọ maṣe da awọn ọja pada si RTI laisi aṣẹ ipadabọ.
Atilẹyin ọja to lopin
RTI ṣe iṣeduro awọn ọja tuntun fun akoko ti ọdun mẹta (laisi awọn ohun elo bii awọn batiri gbigba agbara eyiti o jẹ atilẹyin ọja fun ọdun kan) lati ọjọ rira nipasẹ olura atilẹba (olumulo ipari) taara lati Iṣakoso RTI / Pro ( ninu eyi tọka si bi “RTI”), tabi oniṣowo RTI ti a fun ni aṣẹ.
Warranty claims may be initiated by an authorized RTI dealer using the original dated sales receipt or other proof of warranty coverage. In the absence of the receipt of purchase from the original dealer, RTI will provide warranty coverage extension of six (6) months from the date code of the product.
Akiyesi: RTI warranty is limited to the provisions set forth in this policy and does not preclude any other warranties offered by third parties who are solely responsible for those other warranties.
Ayafi bi a ti sọ ni isalẹ, atilẹyin ọja ni wiwa awọn abawọn ninu ohun elo ọja ati iṣẹ-ṣiṣe. Awọn atẹle ko ni aabo nipasẹ atilẹyin ọja:
- Ọja ti o ra nipasẹ awọn ti o ntaa laigba aṣẹ tabi awọn aaye intanẹẹti kii yoo ṣe iṣẹ- laibikita ọjọ rira.
- Awọn ibajẹ ti o ṣẹlẹ nipasẹ ijamba, ilokulo, ilokulo, aibikita tabi awọn iṣe Ọlọrun.
- Ibajẹ ohun ikunra, pẹlu, ṣugbọn kii ṣe opin si, awọn idọti, dents ati yiya ati yiya deede.
- Ikuna lati tẹle awọn ilana ti o wa ninu Itọsọna fifi sori ọja.
- Awọn ibajẹ nitori awọn ọja ti a lo ninu ohun elo tabi agbegbe miiran yatọ si eyiti a pinnu fun, awọn ilana fifi sori ẹrọ ti ko tọ tabi awọn ifosiwewe ayika ti ko dara gẹgẹbi laini ti ko tọ vol.tages, aibojumu onirin, tabi insufficient fentilesonu.
- Tunṣe tabi igbiyanju atunṣe nipasẹ ẹnikẹni miiran yatọ si RTI ati Iṣakoso Pro tabi awọn alabaṣiṣẹpọ iṣẹ ti a fun ni aṣẹ.
- Ikuna lati ṣe iṣeduro itọju igbakọọkan.
- Awọn idi miiran ju awọn abawọn ọja lọ, pẹlu aini ọgbọn, ijafafa tabi iriri olumulo.
- Bibajẹ nitori gbigbe ọja yi (awọn ẹtọ gbọdọ ṣe si ti ngbe).
- Ẹyọ ti a yipada tabi nọmba ni tẹlentẹle ti a yipada: ti bajẹ, ti yipada tabi yọkuro.
Iṣakoso RTI ko tun ṣe oniduro fun:
- Awọn ibajẹ ti o ṣẹlẹ nipasẹ awọn ọja rẹ tabi fun ikuna ti awọn ọja rẹ lati ṣe, pẹlu eyikeyi idiyele iṣẹ, awọn ere ti o sọnu, awọn ifowopamọ ti o sọnu, awọn bibajẹ lairotẹlẹ, tabi awọn bibajẹ to wulo.
- Awọn ibajẹ ti o da lori airọrun, isonu ti lilo ọja, isonu ti akoko, iṣẹ idalọwọduro, ipadanu iṣowo, eyikeyi ẹtọ ti ẹnikẹta ṣe tabi ti a ṣe ni ipo ẹnikẹta.
- Pipadanu, tabi ibaje si, data, awọn ọna ṣiṣe kọnputa tabi awọn eto kọnputa.
RTI’s liability for any defective product is limited to repair or replacement of the product, at the sole discretion of RTI.
In cases where the warranty policy conflicts with local laws, the local laws will be adopted.
Ìkéde ÌWÉ (DOC)
Ikede Ibamu fun ọja yii ni a le rii lori RTI webojula ni: www.rticontrol.com/declaration-of-conformity
Aṣẹ-lori-ara 2025
Latọna Imọ Incorporated
Gbogbo awọn ẹtọ wa ni ipamọ.
Awọn iwe aṣẹ / Awọn orisun
 |
RTI XP-8v Advanced Control Processor [pdf] Itọsọna olumulo XP-8v Advanced Control Processor, XP-8v, Advanced Control Processor, Control Processor, Processor |