RTX 8930 Wireless Dect Headset
LORIVIEW
This manual explains how to operate the RTX SME VoIP DECT Headset (RTX8930) in generic mode, including power on/off, registration, basic call handling, volume control, and microphone muting.
Awọn pato
- Awoṣe: RTX8930 headset
- Iṣakoso iwọn didun: Six volume steps (beeps indicate adjustments and limits)
- LED behavior (power/registration status): Blue LED blinks fast during initial signal detection/registration mode; after subscription it blinks with a 2-second interval
- Power-off key combination: Long-press AUX + VOL+ + VOL- for five seconds
Quick Setup & Use
- Tan-an: Tẹ awọn AUX key. Wait for the blue LED to blink fast until a signal is detected; once subscribed, the voice prompt “Headset subscribed” plays and the blue LED changes to a 2-second interval.
- Initial registration: For first-time setup, switch the headset on; it enters registration mode automatically (blue LED blinking fast).
- Subsequent (re-)registration: Tẹ mọlẹ HOOK OFF pọ pẹlu VOL+ ati VOL- until the blue LED starts blinking fast. (Note: the blue LED will not enter registration mode if the unit is cradled and charging.)
- Dahun ipe kan: Tẹ HOOK OFF.
- Pari ipe kan: Tẹ HOOK OFF lẹẹkansi.
- Adjust volume during a call: Tẹ VOL+ lati mu ati ki o VOL- lati dinku.
- Mu gbohungbohun dakẹ/mu ẹnu rẹ: Tẹ IKU to toggle mute on and off.Headset Operations Manual
Nipa Iwe-ipamọ yii
This document describes the features and functionalities available in the RTX SME VoIP DECT Headset. We describe how to operate the headset without going into details about its mechanical features. The reference for features and operation in this manual is RTX generic mode.
OlugboItọsọna yii jẹ ipinnu fun awọn olumulo lojoojumọ bii awọn alabojuto eto.
Awọn kukuruFun idi iwe yii, awọn kuru wọnyi di:
- DECT: Awọn Ibaraẹnisọrọ Alailowaya Digital Imudara
- IPEI: International Portable Equipment Identity
- MAC: Media Access Iṣakoso
- PBX: Paṣipaarọ Ẹka Aladani
Awọn itọkasi/Awọn iwe ti o jọmọ
- [1]: How_To_Deploy_SME_Network_V1.3
- [2]: SME VoIP System Guide, Version 2.5
Iwe Itan
| Àtúnyẹwò | Onkọwe | Ọjọ itẹjade | Comments |
|---|---|---|---|
| 0.1 | TMS | 26-Jul-2016 | Ibẹrẹ ẹya. |
Aami-iṣowo
| Orukọ Onibara | RTX | Wildix | SNOM | Strongbyte |
|---|---|---|---|---|
| Awoṣe No. | RTX8930headset | WAIR-Headset | A190 | VCV2840 headset |
| HVIN | 8930V10 | WAIRV10 | 190V10 | 2840V10 |
| Aami-iṣowo |
Isẹ ipilẹ
This section describes how to switch on and off the RTX8930 headset and how to register the unit on an RTX 8660 SME VoIP system.
How to Switch the Headset On/Off:
Yipada si pa agbekariTo switch the headset off, long-press the AUX bọtini paapọ pẹlu awọn VOL+ ati VOL- keys (press and hold the three keys for five seconds). The blue LED will give a short blink before switching off.
Registration Initial Registration
Awọn iforukọsilẹ ti o tẹleIf the RTX8930 headset has already been registered on the same or another base system and needs to be re-registered, the required action is to press and hold the HOOK OFF bọtini paapọ pẹlu awọn VOL+ ati VOL- keys until the blue LED starts blinking fast.
AKIYESI: The blue LED will not start blinking in registration mode if the unit is cradled and charging. Please check the additional document via [2] for more information about terminal registration on a base system.
Awọn iṣẹ ipe
- Ipe ti nwọle As the headset receives an incoming call, a ringtone will be played back
- Ndahun ipe ti nwọle Lati dahun ipe ti nwọle, tẹ HOOK OFF bọtini
- Kọ ipe ti nwọle It is not currently possible to reject an incoming call
- Pari ipe kan To end an ongoing call, press the HOOK OFF bọtini
- Iwọn didun ati Muting It is possible to adjust the earpiece volume up or down during calls by pressing the VOL+ ati VOL- keys, respectively. There are six volume steps. A beep is played back to indicate that the volume is adjusted. A higher frequency beep is played back when the volume cannot be adjusted further up or down.
- Dinku gbohungbohun It is possible to mute the microphone during calls by pressing the IKU key. The microphone is unmuted by pressing the IKU key again. A voice prompt announcing “Mute on” is played back when mute is activated. A voice prompt announcing “Mute off” is played back when mute is deactivated.
Laasigbotitusita
- Headset doesn’t enter registration mode when re-registering: If you are cradled and charging, the blue LED will not start blinking fast in registration mode. Remove it from the cradle/charging and try again.
- No confirmation after switching on: Lẹhin titẹ AUX, the blue LED should blink fast until a signal is detected. Once the headset locks onto a base, the voice prompt “Headset subscribed” should play and the LED should switch to blinking with a 2-second interval.
- Volume can’t be increased/decreased: The headset provides higher frequency beeps when the volume cannot be adjusted further up or down.
Awọn iwe aṣẹ / Awọn orisun
 | 8930 Wireless Dect Headset |
Awọn itọkasi
- Itọsọna olumulomanual.tools