Fi Itọsọna sori ẹrọ
CSEN1
CSEN1 Combo Sensor Controller
Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)
Apejuwe
The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.
AWỌN NIPA
- Igbohunsafẹfẹ Redio: 2.4 GHz (IEEE 802.15.4)
- Agbara Ijade Gbigbe RF: +20dBM
- Iwọn otutu ti nṣiṣẹ: -40 ° si + 70 ° C
- Ọriniinitutu ti nṣiṣẹ: 10 si 95%, ti kii-condensing
- IP66 won won apade
- Awọn iwọn: 3.1" D x 1.6" H (80mm D x 42mm H)
- Input Power: 12-24VDC, 35mA max, 840mW
- Idi ti iṣakoso: Ṣiṣẹ
- Environmental: Indoor/Outdoor
- Ipele Idoti: 3
- Won won Ipa Voltage:330V
AWỌN ỌRỌ Apẹrẹ
Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltage ti 10V DC.
- Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
- Pa awọn onirin dimming kuro ni awọn laini AC ti o ba ṣeeṣe.
- O pọju ti 4 DALI-2/D4i Awọn awakọ LED fun oludari, kan si Atilẹyin Synapse ti o ba nilo ipin ti o tobi julọ.
- Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
- Maṣe gbe soke si heatsink tabi si awakọ LED kan.
AKIYESI: Awakọ LED gbọdọ ṣe atilẹyin iṣẹ DIM si PA.
IKILO ATI ikilo
- TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
- Ikuna lati tẹle awọn ilana wọnyi ati awọn ikilọ le sọ atilẹyin ọja di ofo.
- This product must be installed in accordance with national, state, and local electrical codes and requirements.
- If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.
Awọn alaye WIRING IWE ZHAGA 18 SOCKET
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:
- 12-24VDC POWER: Brown
- Common Ground/DALI-: Pink with White Stripe
- DALI+/DIM+: Violet with White Stripe
- Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length
Aworan 1 
Awọn ilana fifi sori ẹrọ
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- Ti o ba wulo, yọọ fila idalẹnu tabi ẹrọ iṣakoso ina ti a fi sori ẹrọ lọwọlọwọ ni ibi ipamọ imuduro.
- Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
- After alignment, push until the CSEN1 is fully seated within the receptacle.
- While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)
Akiyesi: Lati ṣiṣẹ daradara, rii daju pe oludari ti fi sii patapata sinu iho ati yiyi si ipo titiipa.
Ikilọ: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
Aworan 2
Awọn LED ipo
| LED Agbara | Ipo |
| Buluu | On for 3 seconds at Startup, then Off |
| Ipo LED | Ipo |
| Pupa | No script on the device |
| Pupa ti n paju | Aṣiṣe ibaraẹnisọrọ |
| Bulu ti n paju | Communication, No Config |
| Awọ ewe ti n paju | Normal Operation with Motion |
| Paa | Normal Operation, no Motion |
ALAYE Ilana ati awọn iwe-ẹri
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Awọn iwe-ẹri Ile-iṣẹ Canada (IC): Ohun elo oni-nọmba yii ko kọja awọn opin Kilasi B fun awọn itujade ariwo redio lati ohun elo oni-nọmba ti a ṣeto sinu Awọn ilana kikọlu Redio ti Ẹka Awọn ibaraẹnisọrọ ti Ilu Kanada.
Awọn iwe-ẹri FCC ati alaye ilana (AMẸRIKA nikan)
FCC Apá 15 Kilasi B: Ẹrọ yii ni ibamu pẹlu apakan 15 ti awọn ofin FCC. Isẹ jẹ koko ọrọ si awọn ipo meji wọnyi: (1) Awọn ẹrọ wọnyi le ma fa kikọlu ipalara, ati (2) Awọn ẹrọ wọnyi gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa iṣẹ ipalara.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:
- Apakan 15, Ipin B, fun ohun elo Kilasi B
- FCC 96-208 bi o ṣe kan awọn kọnputa B ti ara ẹni ati awọn agbeegbe
- Ọja yii ti ni idanwo ni Ile-iṣẹ Idanwo Itade ti ifọwọsi fun awọn ofin FCC ati pe a ti rii lati pade FCC, Apá 15, Awọn opin Ijadejade. Iwe ti wa ni titan file ati pe o wa lati Synapse Wireless, Inc.
Ti ID FCC fun module inu apade ọja ko ba han nigbati o ba fi sori ẹrọ inu ẹrọ miiran, lẹhinna ita ti ẹrọ ti a fi sii ọja yii gbọdọ tun ṣe afihan aami ti o tọka si FCC ID module ti a fipade. Awọn iyipada (FCC 15.21):
Awọn iyipada tabi awọn iyipada si ohun elo yii ko fọwọsi ni kikun nipasẹ Synapse Wireless, Inc., le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ẹrọ yii.
Itọsi – foju siṣamisi ni https://www.synapsewireless.com/about/patents
Lati kọ ẹkọ diẹ sii ṣabẹwo: synapsewireless.com
Awọn iwe-ẹri
| Awoṣe | CSEN1-H-W-ZHA (white enclosure) or CSEN1-H-G-ZHA (gray enclosure) |
| Ni ID FCC wa | QOQ-GM240P |
| Ni IC | 5123A-GM240P |
| RoHS 3 | 2011/65/EU (2015/863) |
| EU DEDE | (EC) Bẹẹkọ 1907/2006 |
DALI-2 Ifọwọsi Ohun elo Adarí
Awọn iwe aṣẹ / Awọn orisun
 |
Synapse CSEN1 Combo Sensor Controller [pdf] Fifi sori Itọsọna CSEN1-H-W-ZHA, CSEN1-H-G-ZHA, CSEN1 Combo Sensor Controller, CSEN1, Combo Sensor Controller, Sensor Controller, Controller |