USAutomatic Low Current Receiver Installation Guide

USAutomatic Low Current Receiver

O ṣeun fun yiyan ọja yii.
Jọwọ ka iwe afọwọkọ yii ni pẹkipẹki ṣaaju fifi ọja yii sori ẹrọ.

Ọrọ Iṣaaju

• Nkan olugba lọwọlọwọ kekere 030205 jẹ olugba ti o wujade 2 kan, ti n ṣiṣẹ ni 433,92 Mhz ni awose AM/ASK.
• O jẹ apẹrẹ fun awọn eto pipade aifọwọyi ati awọn eto egboogi-burglar pẹlu agbara isinmi kekere pupọ.
• The operating frequency is among the European harmonised frequencies. The antenna is connected with a F- type connector.
• Awọn abajade yiyi jẹ nikan pẹlu KO olubasọrọ pẹlu olubasọrọ to wọpọ kuru si Ilẹ.
• Ipo iṣẹ ti K1 jẹ Pulse ati ti K2 le jẹ Pulse tabi Latch. Ipese agbara jẹ 12 Vdc.
• Ipele IP ti 2X ngbanilaaye awọn fifi sori ẹrọ inu ile nikan.
• Ọja naa ni kikun ni ibamu pẹlu Awọn ilana EMC European (CE) ati Awọn ilana FCC Apá 15.

Ohun elo Atagba

• 2-button transmitter – Part # 030210
• 4-button transmitter – Part # 030212

Imọ ni pato

• Iru olugba: Superheterodyne.
• Demodulation: AM/BERE.
• Igbohunsafẹfẹ ṣiṣẹ: 433,92 MHz.
• Igbohunsafẹfẹ agbegbe oscillator: 6,6128 MHz.
• Agbedemeji igbohunsafẹfẹ: 10,7 MHz.
• Ifamọ (fun ifihan agbara to dara): -115 dBm.
• Input impedance: 75 Ohm.
• Ipese voltage: 12 dc ( ± 10% ).

Gbigba lọwọlọwọ:

• ni isinmi: 1.5 mA
• pẹlu 1 yii yiya: 7 mA
• Nọmba ti relays: 2 (1NO, 1NO).
• Yiyi ipo iṣẹ Pulse / Latch
• Commutable max power: 24W or 24VA.
• Agbara iranti (awọn bọtini tx): 42.
• Operating temperature: -4 ÷ +158 °F.
• Awọn iwọn: 4.13 x 1.77 x 1.1 ni
• Iwọn: 2.29 iwon
• IP Idaabobo ite: 2X

Olugba ti pariview

• P1: Bọtini P1
• P2: Bọtini P2
• LD: Green Led
• CON: I/O Connector
• K1: Relay 1 Ijade
• F: F-Iru asopo
• K2: Relay 2 Ijade

Aworan onirin

Awọn ẹya akọkọ

• Agbara isinmi ti o kere pupọ
• 42 awọn bọtini atagba ipamọ
• Bọtini atagba ẹyọkan tabi piparẹ iranti ni kikun
• Ipo iṣiṣẹ siseto ti 2 relays: asiko, latching
• Eto atagba rọrun

AGBEGBE ETO ATI GBA

• The Transmitter and Receiver operate at 433 MHz. The receiver can store up to 22 unique transmitter codes.

Eto Atagba:
(A ṣe iṣeduro pe ki awọn dipswitches yipada lati eto aiyipada)

1. Ṣii ilẹkun iyẹwu batiri ki o wa awọn dipswitches.
2. Yi awọn dipswitches pada si awọn eto ti o fẹ. Gba silẹ fun itọkasi ojo iwaju.

Bọtini osi Atagba si Eto Olugba:
(Iṣẹ Ṣiṣii/Duro/Pari iṣẹ deede)

1. Press and hold the left transmitter button down. Red light on the transmitter should be on.
2. Lori olugba, Titari bọtini titari P1 titi ti ina LD alawọ ewe yoo wa ni titan.
3. Tu awọn bọtini mejeeji silẹ. Bọtini osi atagba si siseto olugba ti pari.

Bọtini Ọtun Atagba si Eto Olugba:
(Hold-Gate-Open) (Nikan ti aago isunmọ aifọwọyi ṣiṣẹ)
The 2-channel receiver allows for programming the P2 relay from momentary mode (default) to latching mode. The transmitter right button can then be programmed to hold the gate open, overriding the auto-close feature, if activated.

1. Press and hold the right transmitter button down. Red light on the transmitter should be on.
2. Lori olugba, Titari bọtini titari P2 titi ti ina LD alawọ ewe yoo wa ni titan.
3. Tu awọn bọtini mejeeji silẹ.
4. Bọtini ọtun atagba si siseto olugba ti pari.
5. Bayi o gbọdọ ṣeto P2 olugba si ipo latch ni awọn igbesẹ isalẹ.

Eto olugba:
Yiyi P2 siseto lati igba diẹ si ipo idaduro (lati mu ẹnu-ọna ṣii)

1. Lori olugba, tẹ bọtini-titari P2 titi ti ina LD alawọ ewe yoo wa, lẹhinna tu silẹ. Ina LD alawọ ewe yẹ ki o duro.
2. Lakoko ti ina LD alawọ ewe wa ni titan, Titari bọtini titari P1 si isalẹ ki o tu silẹ. Imọlẹ LD alawọ ewe yẹ ki o tan imọlẹ. Ipo latch ti ṣeto.

Ijẹrisi iṣipopada Olugba P2 ti ṣe eto si ipo mimu:

1. Lori olugba, Titari bọtini titari P2 titi ti ina LD alawọ ewe yoo wa, lẹhinna tu silẹ.
2. Imọlẹ LD alawọ ewe yẹ ki o tan imọlẹ. Ti ina LD alawọ ewe ba duro, tun ṣe apakan siseto olugba loke.

Ṣiṣe atunṣe P2 olugba pada si ipo asiko:

1. Lori olugba, Titari bọtini titari P2 titi ti ina LD alawọ ewe yoo wa, lẹhinna tu silẹ. Imọlẹ LD alawọ ewe yẹ ki o tan imọlẹ.
2. Lakoko ti ina LD alawọ ewe wa ni titan, tẹ bọtini-titari P1 si isalẹ ki o tu silẹ. Imọlẹ LD alawọ ewe yẹ ki o jẹ to lagbara. Ipo akoko ti ṣeto.

Erasing Single Transmitter from Receiver Memory:
Awọn eto dipswitch ti atagba lati paarẹ gbọdọ jẹ mimọ.
Ti o ba mọ tẹle awọn igbesẹ isalẹ.

1. Ṣeto awọn dipswitches sinu atagba kan lati baamu awọn eto iyipada ti koodu atagba lati paarẹ.
2. Tẹ mọlẹ bọtini atagba osi.
3. Lori awọn olugba Titari awọn P1 titari-bọtini titi ti alawọ ewe LD ina ba wa ni titan.
   Lẹhinna tu awọn mejeeji silẹ.
4. Tẹ mọlẹ bọtini atagba ọtun.
5. Lori awọn olugba Titari awọn P2 titari-bọtini titi ti alawọ ewe LD ina ba wa ni titan.
   Lẹhinna tu awọn mejeeji silẹ.
6. Atagba ti paarẹ bayi lati iranti olugba.

Erasing all Transmitters from Receiver Memory:

1. Tẹ bọtini P2 lori olugba titi ti ina LD alawọ ewe yoo wa ni titan. Lẹhinna tu bọtini P2 silẹ.
2. Lakoko ti ina LD wa ni titan tẹ awọn bọtini P1 ati P2 nigbakanna ki o dimu titi ina LD alawọ ewe yoo bẹrẹ lati seju laiyara.
3. O yẹ ki o seju awọn akoko 4 lẹhinna gbogbo awọn koodu atagba ti paarẹ.

Afihan NOMBA AGBEGBE

• O ṣee ṣe lati ṣafihan iye awọn bọtini atagba ti o fipamọ sinu iranti.
• Nọmba naa ti han, ni akọsilẹ alakomeji (0 tabi 1), nipasẹ ọna ti awọn filasi mu.
• Filaṣi kukuru (½ iṣẹju-aaya) ti LD funni ni alakomeji “0”.
• Filasi gigun ( 1 iṣẹju-aaya ) ti LD yoo fun alakomeji “1”.
• Ọkọọkan pipe jẹ kq nipasẹ awọn filasi 6 ati nipasẹ filasi to gun ipari kan (awọn aaya 2).
• Gẹgẹbi ipo rẹ, filasi kọọkan ni “iwuwo” ti o yatọ.

First flash: 2 = 1

1. Second flash: 2 = 2
2. Third flash: 2 = 4
3. Fourth flash: 2 = 8
4. Fifth flash: 2 = 16
5. Sixth flash: 2 = 32

Ilana

1. Jeki P1 tabi P2 tẹ mọlẹ titi LD yoo fi tan.
2. Tu bọtini naa silẹ lẹhinna Titari P2 fun igba diẹ ṣaaju ki LD yipada.

Ni aaye yi bẹrẹ awọn ọkọọkan ti seju.
Ṣe akọsilẹ lẹsẹsẹ lati ṣe iṣiro nọmba eleemewa ti o baamu, bi o ṣe han ninu examples.

Es. N° 1: Iranti sofo

• Awọn iwuwo 1 2 4 8 16 32 Ipari Ọkọọkan
• Tẹle: _ _ _ _ __ ____
• Final number : 0 + 0 + 0 + 0 + 0 + 0 = 0

Es. N° 2: 5 awọn bọtini atagba

• Awọn iwuwo 1 2 4 8 16 32 Ipari Ọkọọkan
• Ilana: _ __ __ _ __ ____
• Nọmba ipari: 1+ 0 + 4 + 0 + 0 + 0 = 5

Es. N° 3: 12 awọn bọtini atagba

• Awọn iwuwo 1 2 4 8 16 32 Ipari Ọkọọkan
• Ilana: _ __ __ __ __ ____
• Nọmba ipari: 0 + 0 + 4 + 8 + 0 + 0 = 12

ATILẸYIN ỌJA

• USAutomatic, LLC warrants this product to be free of defects in materials and workmanship for 1 YEAR. For a period of 1 YEAR following purchase, USAutomatic, LLC. will repair or replace the product free of charge, including parts, shop labor and return to customer shipping and handling.
• This 1-year warranty does not cover the plastic case from normal wear or damage due to misuse.
• To have the product sent for warranty consideration, it must be returned with the proof of purchase and a return authorization number. To obtain a return authorization number, please call 1-888-204-0174 for assistance. The return authorization number must be clearly marked on the outside of the return package or it may not be accepted.

Olubasọrọ

• www.usautomaticgateopeners.com
• (888)-378-1170
• sales@usautomaticgateopeners.com