Weihai Printer Mainboard Module Owner’s Manual

Weihai Printer Mainboard Module

Specific Operating Conditions

1. This product is a high-performance printer mainboard (Mainboard Module), specifically designed for printer equipment. The module integrates wireless communication functionality (Wi-Fi) and is intended to serve as a core component installed inside the printer, enabling data transmission and device control with a host computer. It supports communication with the host via USB, Ethernet, or Wi-Fi interfaces to receive print data and execute printing tasks.
2.  Professional Use Limitation: This module has professional user condition restrictions. The host product manufacturer must clearly state the warning “This product is intended for professional users only” in the product manual.
3.  Awọn ilana fifi sori ẹrọ ati ṣiṣe:
   1. Antenna installation: Remove the nut from the antenna, insert the metal end of the antenna through the mounting hole on the main control board bracket, and then reinstall the nut onto the antenna.
   2. Route the antenna through the designated hole as shown in the diagram and plug it into the main control board.
   3. Mount the main board onto the bracket and secure it using an electric screwdriver to install the following four screws (torque setting: 7 ± 0.5 kgf·cm).
   4. Attach the wireless communication module onto the metal end of the antenna.
   5. Plug the printhead harness connector into the main board, and gently bend the adapter cable at the connection end..
   6. Connect the printhead cable as illustrated.
4. Mainboard Usage Instructions
   After completing the above installation steps, toggle the rocker switch on the mainboard—the printer’s indicator light will illuminate brightly.
   The printer will automatically search for the pre-configured end-customer Wi-Fi SSID and connect to it. End users may also use the printer’s accompanying web-based utility tool to modify the Wi-Fi SSID to which the printer should automatically connect.
   Print jobs are sent to the printer via the Wi-Fi interface, and the printer executes the printing tasks accordingly.
5. Operating temperature: 5-45 ℃

Host Product Integration Labeling Instructions

1.  If the FCC Identifier (FCC ID) cannot be clearly seen after the module is installed inside the equipment, a label indicating the contained module must be affixed to the exterior of the equipment. The label format must follow “Contains FCC ID: 2BTZASRN” , complying with FCC KDB guidance 784748 labeling specifications.
2. End-user equipment must comply with the labeling requirements of §15.19. For special equipment labeling rules, please refer to §2.925, §15.19(a)(5), and related KDB documents; electronic labels must comply with §2.935 requirements.

Additional Test Requirements

Test Mode and Additional Test Requirements

1. The Original Equipment Manufacturer (OEM) integrator must ensure there are no instructions for end-users to manually remove or install this module.
2. This module is limited to installation in mobile applications. All other operating configurations (including portable configurations compliant with §2.1093 and different antenna configurations) require separate approval.
3. The host product manufacturer is ultimately responsible for performing additional compliance testing on the end product after installation of this module, including but not limited to tests related to digital device emissions, PC peripheral requirements, and other transmitters within the host.

Test Mode Software Access: Supports Wifi Test . Test items, frequency, transmit power, modulation type, and other parameters can be selected within the test script instructions.

Ogun Ọja

Host Product Manufacturer FCC Other Parts and Part 15B Compliance Requirements

1. This modular transmitter is only certified for the specific rule parts listed in the FCC grant. The host product manufacturer must ensure the host complies with other applicable FCC rules not covered by the modular transmitter certification.
2. Under all circumstances, the host product manufacturer must ensure that the host product with this module installed and operating complies with Part 15B requirements.
3. If the end product is a Class B or Class A digital device or peripheral, its user manual must prominently include the user notice statement specified in §15.105 or a similar statement:

(I) Class B Device Notice:

Akiyesi: Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni nọmba Kilasi B, ni ibamu si apakan 15 ti Awọn ofin FCC. Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to tọ si kikọlu ipalara ni fifi sori ibugbe kan. Ẹrọ yii n ṣe ipilẹṣẹ, nlo ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato. Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:

• Reorient tabi tun eriali gbigba pada.
• Mu iyatọ pọ si laarin ẹrọ ati olugba.
• So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ.
• Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.

 Class A Device Notice:

Akiyesi: Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni-nọmba Kilasi A, ni ibamu si apakan 15 ti Awọn ofin FCC. Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to bojumu lodi si kikọlu ipalara nigbati ohun elo ba ṣiṣẹ ni agbegbe iṣowo kan. Ẹrọ yii n ṣe ipilẹṣẹ, nlo, ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu itọnisọna itọnisọna, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Ṣiṣẹ ohun elo yii ni agbegbe ibugbe le fa kikọlu ipalara ninu eyiti olumulo yoo nilo lati ṣe atunṣe kikọlu naa ni inawo tirẹ.

Awọn Gbólóhùn Ibamu Ilana Ilana FCC

§15.19 Gbólóhùn
Ẹrọ yii ni ibamu pẹlu Apá 15 ti Awọn ofin FCC. Isẹ jẹ koko ọrọ si awọn ipo meji wọnyi: (1) Ẹrọ yii le ma fa kikọlu ipalara, ati (2) ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa iṣẹ ti ko fẹ.
Ohun elo yii ni ibamu pẹlu awọn opin ifihan itankalẹ FCC ti a ṣeto fun agbegbe ti a ko ṣakoso. Ohun elo yii yẹ ki o fi sori ẹrọ ati ṣiṣẹ pẹlu aaye to kere ju 20cm laarin imooru & ara rẹ.

§15.21 Alaye si olumulo

Ikilọ: awọn iyipada tabi awọn iyipada ti ko fọwọsi ni pato nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ohun elo naa.

Gbólóhùn ibamu Ifihan Ifihan RF
This module complies with FCC radiation exposure limits set forth for an uncontrolled environment.. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Alaye ibamu ISED
Ẹrọ yii ni awọn atagba (awọn)/awọn olugba(awọn) ti ko ni iwe-aṣẹ ti o ni ibamu pẹlu Innovation, Imọ ati Idagbasoke Iṣowo Awọn RSS(s) laisi iwe-aṣẹ ti Canada. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:

1. Ẹrọ yii le ma fa kikọlu.
2.  Ẹrọ yii gbọdọ gba kikọlu eyikeyi, pẹlu kikọlu ti o le fa iṣẹ ti a ko fẹ fun ẹrọ naa.

Ohun elo yii ni ibamu pẹlu awọn opin ifihan itankalẹ IC RSS-102 ti a ṣeto siwaju fun agbegbe ti a ko ṣakoso. Ohun elo yii yẹ ki o fi sori ẹrọ ati ṣiṣẹ pẹlu aaye to kere ju 20cm laarin imooru & ara rẹ.

ISED Radiation Ifihan alaye
Ohun elo yii ni ibamu pẹlu awọn opin ifihan itankalẹ IC RSS-102 ti a ṣeto siwaju fun agbegbe ti a ko ṣakoso.
Please notice that if the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 35008-SRN”” any similar wording that expresses the same meaning may be used.

This radio transmitter [IC: 35008-SRN”] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in IC ID (new application) procedure followed by a Class II permissive change application. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Applicable FCC Rules Statement

This modular transmitter complies with FCC Rules Part 15.247, 15.407.

• Restricted Module Statement
  This printer mainboard module is not a restricted module and does not require additional compliance with restricted module-related procedures.
•  Antenna Design Statement
  The antenna supplied with this module is not a microstrip antenna. Therefore, information related to microstrip antenna design layout, Bill of Materials (BOM), and isolation requirements is not required.

1. This module complies with the radiation exposure limits set by the FCC for uncontrolled environments.
2.  When this module coexists with other simultaneously operating transmitters, compliance evaluation must be conducted in accordance with the FCC multiple transmitter procedures.

Antenna Usage Instructions and Compliance Statement

Antenna Specifications and Restrictions:

This device is authorized for use only with the antenna types listed in the table below. Use of uncertified antennas or antennas with gain exceeding the specified limits is strictly prohibited..

RSS-247 Clause  7.3.7 Compliance Statement

Pursuant to Clause 7.3.7 of Innovation, Science and Economic Development Canada (ISED) standard RSS-247, the following declarations are made:
Antenna Replacement Restriction:

1. This device is equipped with a removable antenna connector. Users must not arbitrarily replace the antenna type or use an antenna with gain exceeding the authorized limit.
2. Liability Statement: Any unauthorized antenna replacement or modification may cause the device to exceed permissible radiation emission limits and could result in the user losing legal authorization to operate the device. Should an antenna change be required, the manufacturer must submit a Permissive Change Application.
3. Ìkìlọ̀ Ìdènà:
   1. Ẹrọ fun išišẹ ni ẹgbẹ 5150-5250 MHz jẹ nikan fun lilo inu ile lati dinku agbara fun kikọlu ipalara si awọn ọna ẹrọ satẹlaiti alagbeka-ikanni;
   2. Ere eriali ti o pọju ti a gba laaye fun awọn ẹrọ ninu awọn ẹgbẹ 5250-5350 MHz ati 5470-5725 MHz yoo ni ibamu pẹlu opin eirp; ati
   3. Ere eriali ti o pọju ti a gba laaye fun awọn ẹrọ ti o wa ninu ẹgbẹ 5725-5825 MHz yoo ni ibamu pẹlu awọn opin eirp ti a sọ fun aaye-si-ojuami ati iṣẹ ti kii ṣe aaye-si-ojuami bi o ṣe yẹ.

A akojọ ti gbogbo awọn eriali orisi

FAQ