xylem FlexNet CommandLink II Wireless Interface User Guide

Awọn ọna Itọsọna
AQG-10087-05
FlexNet CommandLink II

FlexNet CommandLink II Wireless Interface

The CommandLink® II wireless interface provides access to a complete suite of functional controls within a gas, water, or electric SmartPoint® transceiver. This Bluetooth® enabled device, coupled with a handheld, can perform activations, deactivation, meter read, on-demand reads, and audits of the SmartPoint module.

Ikilọ: Risk of hot surface. Do not hold the device longer than one (1) minute when operating in an ambient temperature above 40°C (104°F).

Igbesẹ 1: Gba agbara si CommandLink II
You must charge the CommandLink II completely before first use.

1. Plug the charging adapter into a power outlet and connect to the Charging Port located next to the Mag Loop on top of the Command Link II.
   Akiyesi: Make sure you have rechargeable batteries installed before using a power outlet.
   Awọn iwọn ti o ni awọn batiri ti kii ṣe gbigba agbara ko yẹ ki o ṣafọ sinu iṣan agbara fun gbigba agbara.
2. Atọka LED pupa n tan imọlẹ, nfihan pe ẹyọ naa n gba agbara.
3. Unplug the unit when the red LED is no longer illuminated, indicating the CommandLink II is fully charged.
   Akiyesi: To power down the CommandLink II immediately, press and hold the power button located on the side of the CommandLink II until the PWR LED turns off.

Igbesẹ 2: Tan Ọna asopọ Aṣẹ II

1. Tẹ bọtini agbara.
2. Ina LED alawọ ewe tan imọlẹ nigbati CommandLink II ti ni agbara ni aṣeyọri.

Igbesẹ 3: Ṣẹda Ajọṣepọ Bluetooth kan
To use the CommandLink II, you must first establish a Bluetooth partnership with a Windows Mobile, Android, or iOS-equipped handheld device (HHD) or PC.

Package Awọn akoonu

• FlexNet CommandLink II
• Awọn okun Bungee (2)
• Adapter Gbigba agbara (AC/DC)
• Adapter Gbigba agbara ọkọ (DC/DC)
• Ọran

Ti o ba nlo Ẹrọ Imudani Alagbeka Windows kan:

1. Yan Bẹrẹ, lẹhinna Eto.
2. Select Connections, then select Bluetooth COM.
   Power on the CommandLink II if it is off.
3. Yan Awọn ẹrọ Iwari.
   A list of all the Bluetooth-enabled devices in range is generated and displayed.
   If your CommandLink II does not appear in the list, make sure that it is powered on. If it is powered on, power cycle it and select Discover Devices again, and repeat this step.
4. Yan tirẹ
   CommandLink II from the list and select Connect.
5. If you are prompted toSet the Bluetooth PIN, enter 0000 and select OK.
6. Yan O DARA lati jade.
7. Yan X ni igun apa ọtun isalẹ lati jade.
8. Yan Awọn irin-iṣẹ FieldLogic lati Ibẹrẹ akojọ.
9. From the FieldLogic Tools main screen, select Menu, and select Options.
10. Yan taabu FlexNet ko si yan CommandLink lati inu atokọ iru ẹrọ iru ẹrọ. Maṣe yan CLxxxxxxxx_BLE.
11. Yan Gba Ipo. Awọn irinṣẹ FieldLogic sopọ pẹlu CommandLink II ati ṣafihan ifiranṣẹ aṣeyọri kan.
12. Yan O DARA.
13. Yan O dara lẹẹkansi lati pada si iboju Sopọ.

Ti o ba lo ẹrọ Android kan:

1. Yan aami Eto.
2. Select Options, then select FlexNet. FieldLogic displays a list of available devices.
3. Yan + si view iboju sisopọ eto.AQG – 10007 – 05
4. Yan CommandLink II rẹ (CLxxxxxxxx) lati inu atokọ ti awọn ẹrọ Bluetooth ti o wa.
5. Yan Sopọ. CommandLink II rẹ yoo han ni atokọ Awọn ẹrọ ti a so pọ.
6. Pada si Awọn irinṣẹ FieldLogic.
7. Select the newly-paired CommandLink II in the list and select the information symbol.FieldLogic sopọ si CommandLink II ati ṣafihan ifiranṣẹ aṣeyọri kan.
8. Yan Pade.
9. Yan itọka ẹhin lati pada si iboju akọkọ FieldLogic.

Ti o ba nlo Ẹrọ Imudani iOS:

1. Yan aami Eto.
2. Yan Awọn aṣayan, lẹhinna yan FlexNet. FieldLogic ṣe ayẹwo fun ẹrọ ati lẹhinna ṣafihan awọn ẹrọ to wa. Atokọ naa n sọdọtun laifọwọyi.
3. Awọn ifihan window agbejade igbanilaaye. Yan O DARA.
4. Yan CommandLink II rẹ (CLxxxxxxxx) lati inu atokọ ti awọn ẹrọ Bluetooth ti o wa.
   
5. Select your CommandLink II and then select the information symbol.
6. FieldLogic sopọ si CommandLink II ati ṣafihan ifiranṣẹ aṣeyọri kan.
7. Yan Sunmọ lati pada si iboju Awọn aṣayan.
8. Yan itọka ẹhin lati pada si iboju akọkọ FieldLogic.

Ti o ba nlo PC:

1. Agbara soke CommandLink II.
2. Yan aami Bluetooth lori tabili kọmputa rẹ tabi lati Ibẹrẹ akojọ.
3. Lati inu PAN Awọn ẹrọ Bluetooth, yan Fi ẹrọ kan kun.
4. Kọmputa rẹ n wa awọn ẹrọ lati ṣafikun.
5. Select the icon containing the CommandLink II ID number (CLxxxxxxxx).
   Akiyesi: If two numbers appear, make sure you select CLxxxxxxxx. Do not select CLxxxxxxxx_BLE.
6. Yan Next.
7. Your computer confirms the successful addition of the CommandLink II.
8. Yan Sunmọ lati tẹsiwaju.
9. Bẹrẹ Awọn irinṣẹ FieldLogic. Lati iboju akọkọ, yan Awọn irin-iṣẹ ko si yan Aw.
10. Yan FlexNet Eto faagun ki o yan CommandLink lati inu atokọ jabọ-silẹ Ẹrọ Ibaraẹnisọrọ. Yan ẹrọ rẹ lati inu atokọ jabọ-silẹ orukọ ẹrọ.
11. Select Get Status.
    FieldLogic Tools connects with the CommandLink II and displays a success message.
12. Yan O DARA lati pada si iboju Awọn aṣayan.
13. Yan O DARA lati pada si iboju Sopọ.

Attach a Strap to the CommandLink II

To attach a strap, slide it in between the slots on the sides of the unit.

AQG – 10007 – 05

Awọn Gbólóhùn Ibamu

AKIYESI
Any modifications made to this device that are not approved by Sensus may void the authority granted to the user by the FCC to operate equipment.

AKIYESI
Fun Kilasi B – Awọn Radiators airotẹlẹ:
This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

AKIYESI
ICES-003 Kilasi B Akiyesi-Avis NMB-003, Kilasi B
Ohun elo oni-nọmba Kilasi B yii ni ibamu pẹlu ICES-003 ti Ilu Kanada.

AKIYESI
Akiyesi: Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni-nọmba Kilasi B kan, ni ibamu si Apá 15 ti Awọn ofin FCC.
Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to tọ si kikọlu ipalara ni fifi sori ibugbe kan. Ẹrọ yii n ṣe ipilẹṣẹ, nlo, ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato. Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:

• Reorient tabi tun eriali gbigba pada
• Mu iyatọ pọ si laarin ẹrọ ati olugba
• So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ
• Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ

AKIYESI
Ẹrọ yii ni ibamu pẹlu iwe-aṣẹ ile-iṣẹ Canada-alayokuro(awọn) RSS. Isẹ jẹ koko-ọrọ si awọn ipo meji wọnyi: (1) Ẹrọ yii le ma fa kikọlu, ati (2) ẹrọ yii gbọdọ gba kikọlu eyikeyi, pẹlu kikọlu ti o le fa iṣẹ ti a ko fẹ fun ẹrọ naa.

AKIYESI
This radio transmitter, the Sensus CL201, has been approved by Industry Canada to operate with the antenna types listed below, with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

AKIYESI
Labẹ awọn ilana ile-iṣẹ Canada, atagba redio le ṣiṣẹ nikan ni lilo eriali ti iru ati ere ti o pọju (tabi kere si) ti a fọwọsi fun atagba nipasẹ Ile-iṣẹ Canada. Lati dinku kikọlu redio ti o pọju si awọn olumulo miiran, iru eriali ati ere yẹ ki o yan bẹ pe agbara isotropic radiated deede (eirp) ko ju iyẹn ṣe pataki fun ibaraẹnisọrọ aṣeyọri.

IKILO
There is a danger of explosion if batteries are mishandled or incorrectly replaced. On systems with replaceable batteries, replace only with the same manufacturer and type or equivalent type recommended per the instructions provided in the product service manual.
Maṣe ṣajọ awọn batiri tabi gbiyanju lati saji wọn ni ita ẹrọ naa. Ma ṣe sọ awọn batiri nù sinu ina.
Sọ awọn batiri sọnu daradara ni ibamu pẹlu awọn ilana olupese ati awọn ilana agbegbe.

IKILO
MAA ṢE sun tabi tẹ awọn sẹẹli batiri si awọn iwọn otutu ti o kọja 212°F. Iru itọju bẹẹ le fa rupture sẹẹli.

IKILO
EXPLOSION HAZARD – BATTERIES MUST ONLY BE CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS.

xylem.com
SENSUS | 637 Davis Drive | Morrisville, NC 27560 | 800.638.3748 | sensus.com

©2026 Sensus. All products purchased and services performed are subject to Sensus’ terms of sale, available at either sensus.com/TC or 1-800-638-3748. Sensus reserves the right to modify these terms and conditions in its own discretion without notice to the customer. The Sensus logo is a registered trademark of Sensus.
This document is for informational purposes only, and SENSUS MAKES NO EXPRESS WARRANTIES IN THIS DOCUMENT. FURTHERMORE, THERE ARE NO IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES AS TO FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. ANY USE OF THE PRODUCTS THAT IS NOT SPECIFICALLY PERMITTED HEREIN IS PROHIBITED.