ZigBee 3.0 Wireless Push Button Smart Scene Switch Controller User Manual

ZigBee 3.0 Wireless Push Button Smart Scene Switch Controller

ọja Alaye

Awọn ẹya ara ẹrọ

• Le ti wa ni dari nipasẹ iOS foonu / Android foonu
• Ṣe atilẹyin fun APP “Smart Life” ati “Tuya Smart”
• Voice control: Compatible with Alexa and Google home T mall Genie or Xiaodu speakers
• Iṣẹ akoko: Tan/pa a laifọwọyi pẹlu iṣẹ akoko
• Aabo apọju fun rirọpo irọrun ti awọn iyipada ẹrọ ibile rẹ (nilo eedu)
• Smart si nmu
• Ẹgbẹ ẹrọ

Aabo Alaye

Risk of electric shock: Electricity can cause personal injury and properly damage if not handled properly. If you are unsure of any part of these instructions, seek professional help from a qualified electrician.

Fi sori ẹrọ

Akiyesi:

• Rii daju pe agbara lori ẹrọ fifọ Circuit ti wa ni pipa ṣaaju wiwa.
• Neutral wire is required. Verify that the wall box contains a neutral wire (usually white). If the wall box does not have a neutral wire, try another location in the home or call a professional electrician to install the switch.
• Awọn awọ waya ti a tọka si ninu iwe afọwọkọ yii jẹ awọn awọ deede ati pe o le yatọ ni diẹ ninu awọn ile.
• Make sure the wire conductors are securely attached to each screw.
• Rii daju pe ifihan Wi-Fi jẹ iduroṣinṣin ati ṣiṣẹ daradara ṣaaju wiwa.
• Ti o ko ba ni iriri eyikeyi onirin, jọwọ pe oniṣẹ ẹrọ ina mọnamọna.

Igbesẹ akọkọ:

• Pa ẹrọ fifọ Circuit ki o ṣe idanwo agbara pẹlu oluyẹwo itanna kan.
• Rii daju pe iyipada ti wa ni pipa ṣaaju wiwa.

Igbesẹ Keji:

• Remove existing wall panels; turn on power at breaker and use electrical tester to check which wire is the line; the tester will beep when near the line.
• Turn off the power at the circuit breaker; if there is a power outage, use an electrical tester, pull the existing switch out; mark the wiring and other wires; disconnect the power with pliers and remove the wires from the existing switch.
• Connect the switch wires to the wall box with the wire conductors according to the wiring diagram below.
• Igbesẹ kẹta: Install the switch using the screws provided and snap the wall plate onto it.
• Igbesẹ kẹrin: Tan-an agbara pada si ẹrọ fifọ, lẹhinna tan awọn ina.

Aworan onirin

The Live wire is connected to the “L” terminal, The Neutral wire is connected to the “N” terminal, Lighting wire is connected to “L1, L2, L3” terminals.

1. Gang switch lighting wire connection: “L1” terminal
2. Gang switch lighting wire connection: “L1,L2” terminals
3. Gang switch lighting wire connection: “L1,L2,L3” terminals

Fi ẹrọ kun

Add device to “Smart Life” or “Tuya Smart” APP

1. Step 1: Download and install the “Smart Life” or “Tuya Smart” APP: Scan the QR code below
   
2. Step 2: Enter the phone settings option, turn on the Bluetooth and WiFi functions, and turn on the product at the same time
3. Igbesẹ 3: Ṣi ohun elo Smart Life, forukọsilẹ ki o wọle sinu akọọlẹ rẹ, ti o ba ni akọọlẹ Smart Life kan, kan wọle.
4. Step 4: Power on after the wiring is completed, the device is powered on by default, press and hold the touch wall switch button for about 8, until the WiFi blue LED flashes quickly, enter the network configuration mode
5. Step 5: Enter the App, click the “+” at the top right of the page to enter the network connection page.
6. Step 6: Make sure your device’s light is blinking quickly(2 times per second) tap to proceed to the next steр.
7. Step 7: Enter your WiFi and password
8. Igbese 8: Sọ orukọ ẹrọ rẹ fun orukọ rẹ.
9. Step 9: When the WiFi LED is on, the device is online.
   Gba iṣakoso ni bayi!

How to use smart speakers to control devices, such as Amazon Alexa, Google Assistant or T mall Genie?
Ṣí àpù Smart Life láti tẹ “Èmi” wọlé view and find the user Quide for “Me” view and find the user guide the corresponding smart speaker

【Note: Before using the smart speaker, please log in to your account on Amazon Alexa Google Assistant, or T mall Genie.]

Ifihan iṣẹ iṣakoso latọna jijin RF

Packaged products are paired at the factory and do this wirelessly. If you need to add or replace the remote control switch, please refer to the following steps

Ọna asopọ pọ
Press and hold the touch wall switch button for about 3 seconds. The red LED indicator lights up to enter the RF433 pairing mode. At this time, press the RF433 remote control switch a few times and the indicator light flashes off. The switch is controlled and paired successfully.

Ọna imukuro koodu

Long press the touch wall switch button for 5 seconds until the red LED indicator flashes 3 times, the code is cleared successfully.