ATOMSTACK L2 Smart Z-Axis Module
Ilana fifi sori ẹrọ oluyipada giga Z-axis L2-5W/L2-10W/L2-20W/L2-40W
Akiyesi: Awọn aworan wa fun itọkasi nikan, jọwọ tọka si ọja gangan. Fun alaye diẹ sii, jọwọ ṣayẹwo koodu QR naa.
akojọ
Z axis fifi sori ọna
A5 PRO V2 / A10 PRO V2
Yọ awọn pcs 4 M4*6 lọna aago lati yọ esun naa kuro
Fi sori ẹrọ A5 Pro V2/A10 Pro V2 asopo igbẹhin
Di 4 PC M4 * 6
A20 PRO V2 / A40 PRO V2
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO / A48 Ultra ko si iwulo lati tun awọn iyipada opin si
Igbesẹ 1
- Isipade lori engraver
- Yọ 2 skru pa iye yipada ọkọ
- Gbe siwaju ọkọ lati mö 2 ihò
- Titiipa awọn skru 2 pada si ọkọ
- Pari
- Isipade lori engraver
Ọna fifi sori ẹrọ iṣọkan lesa
Igbesẹ:1 Yọ 4 PC M3 ati lesa esun
Igbesẹ:2 Fi sori ẹrọ esun laser pẹlu awọn skru 4 M3 kuro ni igbesẹ 1
Akiyesi: Yọ Nkan ti n ṣatunṣe pẹlu screwdriver agbelebu ni ohun elo irinṣẹ ni akọkọ, lẹhinna fi ẹrọ yiyọ laser si A48 lesa
Ọna asopọ okun
Lesa fifi sori ọna
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2
Akiyesi: Nigbati agbara ba wa lati lo oluṣatunṣe adaṣe giga giga Z-axis, o nilo nikan lati tẹ” idojukọ aifọwọyi “bọtini lori apoti iṣakoso si idojukọ aifọwọyi lesa
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral
Akiyesi: Iboju naa nilo nigba lilo oluṣatunṣe adaṣe giga Z-axis, o nilo lati ṣakoso rẹ lati opin ifihan
- Iṣẹ onibara: Fun eto imulo atilẹyin ọja, jọwọ ṣabẹwo si osise wa webojula: www.atomstack.com Fun atilẹyin imọ-ẹrọ ati iṣẹ, jọwọ fi imeeli ranṣẹ: support@atomstack.com
- Olupese: Shenzhen AtomStack Technologies Co., Ltd
- Adirẹsi: Ilẹ 17th, Ilé 3A, Ipele II, Egan Imọye, No.. 76, Baohe Avenue, Bip code: tret, Longgang District, Shenzhen, Guangdong, China
- Ṣayẹwo koodu QR: TABI oluka koodu / ọlọjẹ koodu tabi eyikeyi ohun elo pẹlu ọlọjẹ kan
Awọn iwe aṣẹ / Awọn orisun
 | L2 Smart Z-Axis Module |
Awọn itọkasi
- Itọsọna olumulomanual.tools
I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?
Lati so awọn ATOMSTACK L2 Smart Z-Axis Module si tirẹ A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.
Ni ibamu si awọn Section 05 — Cable connection method for the A20 PRO V2:
If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small ohun ti nmu badọgba ọkọ tabi a Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.
I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .
Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?
Based on the installation manual for the ATOMSTACK L2 Smart Z-Axis Module, the components you are looking for are part of the cable connection setup (Section 05):
Akiyesi: If you do not see extra ports, ensure you are looking at the pada of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series versus the Pro/Ultra series.
I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?
Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:
Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.
Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact support@atomstack.com fun ijerisi.
Now what do I do ?
What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?
Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:
If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.
>